Confirming your payment

Skip to content

Opening your dashboard

Class 11 Physics Chapter 8 Mechanical Properties Of Solids: Competency-Based Questions (CBQ)

80 questions on Chapter 8, each worked through on its own page with the AI tutor. Class 11 Physics, CBSE 2026-27.

80 questions

1–5 marks · Mixed difficulty

  1. 1

    Question 1

    A 12 kg lamp hangs from the ceiling of a hall by a single aluminium wire of diameter 1.6 mm. The electrician wants to know whether the wire is working safely within its elastic range. Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2} and the yield strength of aluminium σy=95×106 N m−2\sigma_y = 95 \times 10^6\ \text{N m}^{-2} (Table 8.1). Which statement is correct?

    MCQMedium
    1 mark
  2. 2

    Question 2

    A materials lab tests three identical copper blocks. The first is pulled in tension, the second is sheared by forces parallel to its top and bottom faces, and the third is squeezed from all sides by a fluid. In each test the stress has the same magnitude, 2.0×107 N m−22.0 \times 10^7\ \text{N m}^{-2}. For copper, Young's modulus is 110 GPa110\ \text{GPa} (Table 8.1), the shear modulus 42 GPa42\ \text{GPa} (Table 8.2) and the bulk modulus 140 GPa140\ \text{GPa} (Table 8.3). What are the longitudinal strain, the shearing strain and the volume strain, in that order?

    MCQMedium
    1 mark
  3. 3

    Question 3

    A technician finds a coil of unlabelled metal wire. She clamps 3.0 m of it vertically, hangs a load of 100 N from it, and finds that it stretches by 1.5 mm. The cross-sectional area of the wire is 1.0 mm21.0\ \text{mm}^2. Using the Young's moduli in Table 8.1 (aluminium 70 GPa, copper 110 GPa, wrought iron 190 GPa, steel 200 GPa), what is the Young's modulus of the wire, and which metal is it most likely to be?

    MCQMedium
    1 mark
  4. 4

    Question 4

    Two guy-wires made of the same steel hold up a radio mast. Wire A has length LL and diameter dd; wire B has length 2L2L and diameter 2d2d. Both carry the same tension. What is the ratio of the extension of A to the extension of B?

    MCQMedium
    1 mark
  5. 5

    Question 5

    Identify the main type of stress in each of the following situations:

    (1) the rope from which a bucket of water hangs in a well;

    (2) a leg of a table on which a heavy television stands;

    (3) a sheet of paper at the point where it is being cut by a pair of scissors;

    (4) the layer of glue in a lap joint, where two overlapping strips of wood are glued face to face and then pulled apart along their length.

    MCQMedium
    1 mark
  6. 6

    Question 6

    A rigid steel pressure-test chamber is completely filled with 2.0 litres of water. The pressure of the water is then raised by 2.0×107 N m−22.0 \times 10^7\ \text{N m}^{-2}. Taking the bulk modulus of water as B=2.2×109 N m−2B = 2.2 \times 10^9\ \text{N m}^{-2} (Table 8.3), by how much does the 2.0 L of water shrink?

    MCQMedium
    1 mark
  7. 7

    Question 7

    A diver carries two thin, flexible plastic bags down a swimming pool. One holds 1.0 litre of air and the other 1.0 litre of water. He takes both bags 0.20 m deeper. Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}, the density of pool water 1000 kg m−31000\ \text{kg m}^{-3}, and the bulk moduli from Table 8.3: air 1.0×105 N m−21.0 \times 10^5\ \text{N m}^{-2} and water 2.2×109 N m−22.2 \times 10^9\ \text{N m}^{-2}. Which statement about the decrease in volume of the two bags is correct?

    MCQMedium
    1 mark
  8. 8

    Question 8

    In a tensile test, a metal specimen with a gauge length of 50 mm and a cross-sectional area of 25 mm225\ \text{mm}^2 gives the following readings of load and extension of the gauge length.

    StageLoadExtension
    End of the straight-line (proportional) part4.5 kN0.045 mm
    Largest load reached9.5 kN2.6 mm
    Specimen breaks8.0 kN7.0 mm

    What are Young's modulus and the ultimate tensile strength of the metal?

    MCQMedium
    1 mark
  9. 9

    Question 9

    An engineer tests two materials, P and Q, in tension and obtains the stress–strain curves shown (drawn to the same scale). The crosses mark the points where the specimens break.

    Class 11 Physics Mechanical Properties Of Solids

    Which of the two materials is brittle, and why?

    MCQMedium
    1 mark
  10. 10

    Question 10

    A student tests an elastic bungee cord. Unstretched, a marked length of the cord is 1.00 m and its diameter is 4.00 mm. When stretched, the marked length becomes 1.10 m and the diameter falls to 3.84 mm. What is the Poisson's ratio of the cord material?

    MCQMedium
    1 mark
  11. 11

    Question 11

    A student wants a steel wire whose extension is large enough to measure with a travelling microscope: at least 1.0 mm when a load of 50 N hangs from 2.0 m of wire. Young's modulus of steel is 2.0×1011 N m−22.0 \times 10^{11}\ \text{N m}^{-2} (Table 8.1). What condition must the diameter of the wire satisfy?

    MCQMedium
    1 mark
  12. 12

    Question 12

    A craftsman hangs weights from a copper wire of diameter 0.80 mm to find out how much it can hold. The ultimate tensile strength of copper is 400×106 N m−2400 \times 10^6\ \text{N m}^{-2} and its yield strength is 200×106 N m−2200 \times 10^6\ \text{N m}^{-2} (Table 8.1). Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}. What is the largest mass the wire can hold before it breaks?

    MCQMedium
    1 mark
  13. 13

    Question 13

    A student hangs loads from a steel wire 2.0 m long and 0.50 mm in diameter and records its extension.

    Load (N)01020304050
    Extension (mm)00.511.021.532.042.90

    Up to what load do the readings show that the wire obeys Hooke's law, and what extension would a load of 15 N produce?

    MCQMedium
    1 mark
  14. 14

    Question 14

    A surveyor uses a steel measuring tape 30 m long, whose cross-section is 12 mm wide and 0.20 mm thick. The tape is marked correctly when it lies slack, but in use it is pulled straight with a force of 50 N. Young's modulus of steel is 2.0×1011 N m−22.0 \times 10^{11}\ \text{N m}^{-2} (Table 8.1). By how much does the 30 m tape stretch, and what is the effect on a 30 m measurement?

    MCQMedium
    1 mark
  15. 15

    Question 15

    A copper wire of length 1.1 m and cross-sectional area 0.50 mm20.50\ \text{mm}^2 hangs vertically. For small loads it behaves exactly like a stiff spring, with its extension proportional to the load. Young's modulus of copper is 110 GPa110\ \text{GPa} (Table 8.1). What is the force constant (spring constant) of the wire?

    MCQMedium
    1 mark
  16. 16

    Question 16

    A steel wire and a brass wire of the same length and the same cross-sectional area are joined end to end. The combined wire hangs from a ceiling hook and carries a load at its lower end. Take Young's modulus of steel as 2.0×1011 N m−22.0 \times 10^{11}\ \text{N m}^{-2} and of brass as 1.0×1011 N m−21.0 \times 10^{11}\ \text{N m}^{-2}, and neglect the masses of the wires. Which statement about the two wires is correct?

    MCQMedium
    1 mark
  17. 17

    Question 17

    A cable maker tests two wires drawn from the same batch of steel. The diameter of wire 1 is half the diameter of wire 2. First, both wires carry the same load. Then each is loaded until it breaks. What are the ratio of the stresses (wire 1 : wire 2) under the same load, and the ratio of their breaking loads?

    MCQMedium
    1 mark
  18. 18

    Question 18

    A 5.0 kg instrument is hung from a steel wire 1.5 m long with a cross-sectional area of 0.80 mm20.80\ \text{mm}^2, first in a laboratory on the Earth (g=9.8 m s−2g = 9.8\ \text{m s}^{-2}) and later in a base on the Moon (g=1.62 m s−2g = 1.62\ \text{m s}^{-2}). Young's modulus of steel is 2.0×1011 N m−22.0 \times 10^{11}\ \text{N m}^{-2} (Table 8.1). What are the extensions of the wire in the two places?

    MCQMedium
    1 mark
  19. 19

    Question 19

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): A copper wire and a steel wire of the same length and the same cross-sectional area carry equal loads within their elastic limits. The copper wire stretches more than the steel wire.

    Reason (R): A wire with a larger Young's modulus stretches more under a given load, and copper has the larger Young's modulus of the two.

    MCQMedium
    1 mark
  20. 20

    Question 20

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): The bulk modulus of a gas is not a fixed constant; it depends on the pressure of the gas.

    Reason (R): Young's modulus is defined only for solids.

    MCQMedium
    1 mark
  21. 21

    Question 21

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): Hooke's law is valid only in the linear part of the stress–strain curve of a material.

    Reason (R): Between the proportional limit and the yield point, a wire still returns to its original length when the load is removed.

    MCQMedium
    1 mark
  22. 22

    Question 22

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): Stress is a vector quantity, because the force that produces it is a vector.

    Reason (R): For every material, stress remains proportional to strain right up to the point where the material breaks.

    MCQMedium
    1 mark
  23. 23

    Question 23

    Read the passage and answer the questions that follow.

    The cabin of a passenger lift has a mass of 1200 kg including its full load. It hangs from a steel cable that passes over a pulley at the top of the shaft to the motor. When the lift starts upwards, its acceleration can be as large as 1.5 m s−21.5\ \text{m s}^{-2}. The engineer uses steel with yield strength 250×106 N m−2250 \times 10^6\ \text{N m}^{-2} and Young's modulus 2.0×1011 N m−22.0 \times 10^{11}\ \text{N m}^{-2} (Table 8.1), with a safety factor of 5 on the largest tension. When the cabin is at the ground floor, 50 m of cable hangs between the pulley and the cabin. Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2} and neglect the mass of the cable.

    Class 11 Physics Mechanical Properties Of Solids

    (i) Find the largest tension in the cable.

    (ii) Find the minimum cross-sectional area of the cable, and the diameter of a single solid cable with this area.

    (iii) The cable is actually made by twisting together steel wires, each of diameter 1.0 mm. How many wires are needed at least?

    (iv) The cable has exactly the area found in (ii). By how much does the 50 m length stretch when the tension is at its largest value?

    (v) The empty cabin (mass 640 kg) is at rest at the ground floor, level with the floor of the lobby. Eight passengers of total mass 560 kg step in. By how much does the cabin sink below the lobby floor?

    Medium
    5 marks
  24. 24

    Question 24

    Read the passage and answer the questions that follow.

    A gymnast of mass 60 kg hangs at rest from a pair of rings. Each ring hangs from its own vertical steel cable, 3.0 m long and 2.0 mm in diameter, as shown. For steel take Young's modulus Y=2.0×1011 N m−2Y = 2.0 \times 10^{11}\ \text{N m}^{-2} and yield strength σy=250×106 N m−2\sigma_y = 250 \times 10^6\ \text{N m}^{-2} (Table 8.1). Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2} and neglect the masses of the rings and cables.

    Class 11 Physics Mechanical Properties Of Solids

    (i) Find the tension in each cable and the tensile stress in it.

    (ii) Find the strain in each cable and by how much each cable stretches.

    (iii) Find the total elastic potential energy stored in the two cables.

    (iv) During a move, the gymnast briefly hangs at rest from one ring only. Find the stress and the extension of that cable. Does the cable stay within its elastic region?

    (v) A cheaper set of rings uses aluminium cables of the same length and diameter (Young's modulus 70×109 N m−270 \times 10^9\ \text{N m}^{-2}, yield strength 95×106 N m−295 \times 10^6\ \text{N m}^{-2}, ultimate strength 110×106 N m−2110 \times 10^6\ \text{N m}^{-2}, Table 8.1). How much would each cable stretch when the gymnast hangs from both rings? Comment on whether aluminium is a sensible choice.

    Medium
    5 marks
  25. 25

    Question 25

    Read the passage and answer the questions that follow.

    The deck of a road bridge rests on its piers through rubber bearing pads. Each pad is a block 30 cm × 30 cm in face and 5.0 cm thick; its bottom face is fixed to the pier and its top face to the deck. When a heavy truck brakes on the bridge, a horizontal force of 9.0 kN is passed from the deck to one pad, along its top face, as shown. The shear modulus of the rubber is G=1.0×106 N m−2G = 1.0 \times 10^6\ \text{N m}^{-2}. The shear modulus of steel is 84×109 N m−284 \times 10^9\ \text{N m}^{-2} (Table 8.2).

    Class 11 Physics Mechanical Properties Of Solids

    (i) Find the shearing stress in the pad.

    (ii) Find the shearing strain, and the angle through which the vertical sides of the pad tilt.

    (iii) By how much does the top of the pad move relative to its bottom?

    (iv) If a steel block of the same size were used instead of the rubber pad, how far would its top move under the same force?

    (v) A designer proposes a rubber pad of the same face but twice the thickness. How far would its top move? Using your answers, explain why bridges use rubber pads rather than rigid steel blocks at this point.

    Medium
    5 marks
  26. 26

    Question 26

    Read the passage and answer the questions that follow.

    An ocean research team anchors an instrument line to the sea floor, 5000 m deep, with a solid steel sphere of volume 1.0 m31.0\ \text{m}^3. They wonder how much the deep-sea pressure squeezes it. Take the density of seawater as 1030 kg m−31030\ \text{kg m}^{-3} (assume it does not change with depth), g=9.8 m s−2g = 9.8\ \text{m s}^{-2}, and the bulk moduli from Table 8.3: steel 160×109 N m−2160 \times 10^9\ \text{N m}^{-2}, aluminium 72×109 N m−272 \times 10^9\ \text{N m}^{-2}. Neglect atmospheric pressure.

    (i) Find the pressure of the water on the sphere at the sea floor.

    (ii) Find the fractional change in the volume of the sphere, and the decrease in its volume in cm3\text{cm}^3.

    (iii) Show that for a small change the fractional change in the radius of a sphere is one-third of the fractional change in its volume. Hence find the decrease in the radius of the sphere.

    (iv) The team plans to use the same sphere in a deeper trench. At what depth would the sphere lose 0.05% of its volume?

    (v) If the sphere were made of aluminium instead of steel, how many times as much would its volume decrease at the same depth? Find its fractional change in volume at 5000 m.

    Medium
    5 marks
  27. 27

    Question 27

    A light rod 1.0 m long hangs from a ceiling by two vertical wires attached at its ends: a steel wire at one end and a brass wire at the other. Both wires are 2.0 m long and have a cross-sectional area of 2.0 mm22.0\ \text{mm}^2. A load of 300 N is hung from the rod at a distance xx from the steel wire, and it is found that the rod stays exactly horizontal. Take Young's modulus of steel as 2.0×1011 N m−22.0 \times 10^{11}\ \text{N m}^{-2} and of brass as 1.0×1011 N m−21.0 \times 10^{11}\ \text{N m}^{-2}. (The figure shows the arrangement; the load is not drawn at its actual position.)

    Class 11 Physics Mechanical Properties Of Solids

    (a) Explain why the rod staying horizontal means that the tensions in the two wires must be in the ratio of their Young's moduli.

    (b) Find the tension in each wire.

    (c) Find the distance xx.

    (d) Find the stress in each wire and the extension of the wires.

    Medium
    4 marks
  28. 28

    Question 28

    A climber of weight 800 N hangs at rest from a nylon rope of diameter 10 mm. The length of rope between the climber and the anchor above is 30 m. Take Young's modulus of nylon as 4.0×109 N m−24.0 \times 10^9\ \text{N m}^{-2} and neglect the weight of the rope.

    (a) Find the tensile stress in the rope.

    (b) Find by how much the rope stretches.

    (c) A second climber, of weight 600 N, now hangs at rest from the same rope 10 m below the first. By how much more does the upper 30 m of rope stretch, and by how much does the 10 m of rope between the two climbers stretch?

    Medium
    3 marks
  29. 29

    Question 29

    A car's suspension springs and its front "crumple zone" are both made of steel, but they are designed to behave very differently. The springs must return to their original shape after every bump. The crumple zone is designed to crush in a collision, so that the car comes to rest over a longer distance.

    (a) In terms of the stress–strain curve, in which region must the springs always work? What would happen to a spring that was loaded beyond this region?

    (b) Why should the crumple zone be made of a ductile material rather than a brittle one?

    (c) After a minor collision, the crumpled front of the car does not spring back and has to be replaced. Explain why.

    Medium
    3 marks
  30. 30

    Question 30

    A builder has a timber beam of rectangular cross-section 10 cm × 20 cm. It will span 3.0 m between two supports and carry a load of 2000 N at its centre. The sag of such a beam is δ=Wl34bd3Y\delta = \dfrac{Wl^3}{4bd^3Y}, where bb is the breadth and dd the depth of the beam. Take Young's modulus of wood as 13×109 N m−213 \times 10^9\ \text{N m}^{-2} (Table 8.1).

    (a) Find the sag when the beam is laid on its edge (depth 20 cm).

    (b) Find the sag when it is laid flat (depth 10 cm).

    (c) Find the ratio of the two sags, and explain which way the builder should lay the beam.

    Medium
    3 marks
  31. 31

    Question 31

    The textbook states that for most materials the shear modulus is roughly one-third of Young's modulus, G≈Y/3G \approx Y/3.

    (a) Use the following values from Tables 8.1 and 8.2 to find the ratio Y/GY/G for each metal: steel (Y=200Y = 200 GPa, G=84G = 84 GPa), aluminium (7070, 2525), copper (110110, 4242) and iron (190190, 7070).

    (b) Comment on how well the rule G≈Y/3G \approx Y/3 holds, and what the result tells you about the ease of shearing a metal compared with stretching it.

    (c) Table 8.1 does not list brass, but Table 8.2 gives its shear modulus as 36 GPa. Use the rule to estimate Young's modulus of brass.

    Medium
    3 marks
  32. 32

    Question 32

    A farmer tightens a steel fence wire, 10 m long between two posts and of cross-sectional area 4.0 mm24.0\ \text{mm}^2, until it has been stretched by 5.0 mm. Take Young's modulus of steel as 2.0×1011 N m−22.0 \times 10^{11}\ \text{N m}^{-2} and its yield strength as 250×106 N m−2250 \times 10^6\ \text{N m}^{-2} (Table 8.1).

    (a) Find the tension in the wire.

    (b) Find the elastic potential energy stored in the wire.

    (c) If the wire were stretched by 10 mm instead, how much energy would it store? Would it still be within its elastic region?

    Medium
    3 marks
  33. 33

    Question 33

    Table 8.1 gives the following yield strengths σy\sigma_y and ultimate tensile strengths σu\sigma_u (in units of 106 N m−210^6\ \text{N m}^{-2}): steel 250 and 400, copper 200 and 400, aluminium 95 and 110.

    (a) Find the ratio σy/σu\sigma_y / \sigma_u for each metal.

    (b) A part made of one of these metals is overloaded a little more each day. For which metal is the step from the first permanent stretching to breaking the smallest, so that it gives the least warning? Explain.

    (c) For a hook that should visibly bend well before it can snap, which of the three metals would you choose, and why?

    Medium
    3 marks
  34. 34

    Question 34

    A loaded truck drives over a patch of wet clay and then over a rubber speed-breaker. It leaves deep ruts in the clay, but the speed-breaker, though squashed as the wheels pass, regains its shape immediately afterwards. Explain the difference in terms of elasticity and plasticity.

    Medium
    2 marks
  35. 35

    Question 35

    A wire stretched by a length ll under a final load FF stores elastic potential energy 12Fl\frac{1}{2}Fl. A student argues that the work done should be FlFl, "force times distance". Explain why the energy stored is only 12Fl\frac{1}{2}Fl.

    Medium
    2 marks
  36. 36

    Question 36

    A hanging wire is made of one kind of steel in two parts joined end to end: 1.0 m of wire of diameter 1.0 mm and 1.0 m of wire of diameter 2.0 mm. It carries a load of 150 N. Take Young's modulus of steel as 2.0×1011 N m−22.0 \times 10^{11}\ \text{N m}^{-2} and its yield strength as 250×106 N m−2250 \times 10^6\ \text{N m}^{-2} (Table 8.1). Find the stress and the extension of each part and the total extension. Which part would yield first if the load were increased, and at what load?

    Medium
    2 marks
  37. 37

    Question 37

    A car of mass 1200 kg is towed along a level road by a steel cable 5.0 m long and 6.0 mm in diameter. The car accelerates at 0.50 m s−20.50\ \text{m s}^{-2} while the road and air exert a total resistance of 600 N on it. Take Young's modulus of steel as 2.0×1011 N m−22.0 \times 10^{11}\ \text{N m}^{-2} and assume the cable is horizontal. Find the tensile stress in the cable and by how much the cable stretches.

    Medium
    2 marks
  38. 38

    Question 38

    A diver takes a solid rubber ball deep under water. It becomes slightly smaller but stays perfectly round. Explain why its volume changes but its shape does not, and name the stress and the strain involved.

    Medium
    2 marks
  39. 39

    Question 39

    In old buildings, stone pillars often widen out at the top and bottom where they meet the roof and the floor. Explain why a pillar with such distributed ends can support a greater load than a pillar with rounded ends.

    Medium
    2 marks
  40. 40

    Question 40

    In a tensile test of a ductile metal, the stress is calculated as the applied force divided by the original cross-sectional area of the specimen. Beyond the ultimate point D, the recorded stress falls while the strain keeps growing, until the specimen breaks at E. Why does this happen? And why is the ultimate tensile strength quoted at D, not at the fracture point E?

    Medium
    2 marks
  41. 41

    Question 41

    A steel wire and an aluminium wire, each of length LL and cross-sectional area AA, are joined end to end to make a composite wire of length 2L2L. The composite wire is stretched by a force FF applied at its ends. Take Ysteel=200 GPaY_{\text{steel}} = 200\ \text{GPa} and YAl=70 GPaY_{\text{Al}} = 70\ \text{GPa} (Table 8.1).

    If the composite wire is to be replaced by a single uniform wire of length 2L2L and area AA that stretches by the same amount under the same force, what must the Young's modulus of that wire be?

    MCQHard
    1 mark
  42. 42

    Question 42

    A designer wants a wire that stores as much elastic energy as possible per kilogram of wire, without taking a permanent set. Two materials are considered (Table 8.1):

    MaterialYY (GPa)σy\sigma_y (MPa)ρ\rho (kg m−3\text{kg m}^{-3})
    Steel2002507860
    Aluminium70952710

    Assume each material obeys Hooke's law right up to its yield strength. Which statement is correct?

    MCQHard
    1 mark
  43. 43

    Question 43

    A uniform steel rod of length 2.0 m2.0\ \text{m} and cross-sectional area 1.0 cm21.0\ \text{cm}^2 lies on a smooth horizontal floor. A force of 6.0 kN6.0\ \text{kN} pulls one end along the rod, and a force of 1.0 kN1.0\ \text{kN} pulls the other end in the opposite direction, so the rod accelerates. Take Ysteel=2.0×1011 N m−2Y_{\text{steel}} = 2.0 \times 10^{11}\ \text{N m}^{-2}.

    What is the extension of the rod, and what is the tensile stress at its midpoint?

    MCQHard
    1 mark
  44. 44

    Question 44

    A traffic light of mass 40 kg40\ \text{kg} hangs from the junction of two identical steel cables, each 3.0 m3.0\ \text{m} long with a cross-sectional area of 4.0 mm24.0\ \text{mm}^2. The other ends of the cables are fixed to the tops of two poles at the same height, and the junction hangs 1.2 m1.2\ \text{m} below the level of the tops of the poles, at rest. Take Ysteel=2.0×1011 N m−2Y_{\text{steel}} = 2.0 \times 10^{11}\ \text{N m}^{-2} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}, and neglect the masses of the cables.

    By how much does each cable stretch?

    MCQHard
    1 mark
  45. 45

    Question 45

    A steel bar of natural length 1.0 m1.0\ \text{m} and cross-sectional area 2.0 cm22.0\ \text{cm}^2 is squeezed and forced into a gap between two rigid walls that is 0.15 mm0.15\ \text{mm} shorter than the bar, and it stays there under compression. Take Ysteel=2.0×1011 N m−2Y_{\text{steel}} = 2.0 \times 10^{11}\ \text{N m}^{-2}.

    What force does the bar exert on each wall, and how much elastic potential energy is stored in it?

    MCQHard
    1 mark
  46. 46

    Question 46

    A light rigid bar hangs level from two vertical steel wires, each of cross-sectional area 1.0 mm21.0\ \text{mm}^2. One wire is 2.0 m2.0\ \text{m} long; the other is 0.50 mm0.50\ \text{mm} longer, so it hangs slack until the shorter wire has stretched by 0.50 mm0.50\ \text{mm}. A load of 300 N300\ \text{N} is then hung from the bar, placed so that the bar stays level. Take Ysteel=2.0×1011 N m−2Y_{\text{steel}} = 2.0 \times 10^{11}\ \text{N m}^{-2} and treat both wires as 2.0 m2.0\ \text{m} long in calculating their stiffness.

    What are the tensions in the shorter and the longer wire?

    MCQHard
    1 mark
  47. 47

    Question 47

    Two wires P and Q are made of the same metal and have the same mass. Wire P has length LL and wire Q has length 2L2L. The same load is hung from each wire, and both remain within the elastic limit.

    What is the ratio of the extension of P to that of Q?

    MCQHard
    1 mark
  48. 48

    Question 48

    A steel beam of span 4.0 m4.0\ \text{m}, breadth 0.10 m0.10\ \text{m} and depth 0.20 m0.20\ \text{m} rests on supports at its ends and carries a load of 2.0×104 N2.0 \times 10^{4}\ \text{N} at its centre. The sag of such a beam is δ=Wl34bd3Y\delta = \dfrac{Wl^3}{4bd^3Y}; take Y=2.0×1011 N m−2Y = 2.0 \times 10^{11}\ \text{N m}^{-2} and ignore the beam's own weight.

    Find the sag. The beam is then cut into two separate 2.0 m2.0\ \text{m} beams, each resting on its own end supports, and one of them carries twice the original load at its centre. What is the sag of that beam?

    MCQHard
    1 mark
  49. 49

    Question 49

    A thick book, 4.0 cm4.0\ \text{cm} high with covers 20 cm×15 cm20\ \text{cm} \times 15\ \text{cm}, lies flat on a rough table. A horizontal force of 30 N30\ \text{N} applied to the top cover, parallel to it, shifts the top cover sideways by 2.0 mm2.0\ \text{mm} relative to the bottom cover. Treat the book as a uniform elastic block.

    The same book is then stood on its side, so that it is 15 cm15\ \text{cm} high and its top face measures 20 cm×4.0 cm20\ \text{cm} \times 4.0\ \text{cm}. A horizontal force of 6.0 N6.0\ \text{N} is applied to the top face, parallel to it, while the bottom face is held fixed. How far does the top face shift sideways?

    MCQHard
    1 mark
  50. 50

    Question 50

    The stress–strain curve of a metal tested in tension up to fracture is shown. It is a straight line up to 400 MPa400\ \text{MPa} at a strain of 2.0×10−32.0 \times 10^{-3}; the stress then stays constant while the strain grows until the specimen breaks at a strain of 12×10−312 \times 10^{-3}.

    Class 11 Physics Mechanical Properties Of Solids

    How much work must be done to break a bar of this metal 50 cm50\ \text{cm} long with a cross-sectional area of 2.0 cm22.0\ \text{cm}^2, if the whole bar deforms uniformly?

    MCQHard
    1 mark
  51. 51

    Question 51

    A steel wire of cross-sectional area 1.0 mm21.0\ \text{mm}^2 hangs vertically. When the tension in it is 60 N60\ \text{N} its length is 2500.75 mm2500.75\ \text{mm}; when the tension is 160 N160\ \text{N} its length is 2502.00 mm2502.00\ \text{mm}. The wire obeys Hooke's law throughout.

    What are the natural (unstretched) length of the wire and the Young's modulus of steel?

    MCQHard
    1 mark
  52. 52

    Question 52

    A steel rod of length 1.0 m1.0\ \text{m} is circular in cross-section and tapers uniformly, so that its radius increases steadily from 1.0 mm1.0\ \text{mm} at one end to 2.0 mm2.0\ \text{mm} at the other. It is pulled by a force of 500 N500\ \text{N} applied along its axis at the two ends. Take Ysteel=2.0×1011 N m−2Y_{\text{steel}} = 2.0 \times 10^{11}\ \text{N m}^{-2}.

    What is the extension of the rod?

    MCQHard
    1 mark
  53. 53

    Question 53

    Before a tensile test, two fine marks are scratched 50.0 mm50.0\ \text{mm} apart on a metal specimen. The specimen is pulled until it breaks, and the two broken pieces are fitted back together; the marks are now 62.0 mm62.0\ \text{mm} apart. The same test on a glass rod leaves its marks practically the same distance apart.

    What is the percentage elongation at fracture of the metal, and what does the comparison show?

    MCQHard
    1 mark
  54. 54

    Question 54

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): A single value of Young's modulus cannot describe the elastic tissue of the aorta over the whole range of strain in which it still returns to its original length.

    Reason (R): Aorta tissue returns to its original length only for very small strains, so its elastic region is tiny.

    MCQHard
    1 mark
  55. 55

    Question 55

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): A light wire hangs from a ceiling and carries a load of weight FF at its lower end. The tension at any cross-section of the wire is 2F2F, because the ceiling pulls up on the wire with a force FF and the load pulls down on it with a force FF.

    Reason (R): The stress in a stretched wire is its tension multiplied by its area of cross-section.

    MCQHard
    1 mark
  56. 56

    Question 56

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): When a wire is stretched, its diameter decreases even though no force acts on its curved surface.

    Reason (R): Poisson's ratio is the ratio of the lateral stress to the longitudinal stress in a stretched wire.

    MCQHard
    1 mark
  57. 57

    Question 57

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): A load-bearing steel rod may safely be designed so that its working stress is right up to the ultimate tensile strength of steel.

    Reason (R): When a rod is stressed beyond its yield point and then unloaded, it returns to its original length.

    MCQHard
    1 mark
  58. 58

    Question 58

    A thin steel ring (a hoop) of radius RR spins about an axis through its centre, perpendicular to its plane, so that every part of it moves with speed vv. The only forces on any small piece of the ring are the pulls of the neighbouring parts, so the tension in the ring must supply the centripetal force. Take the density of steel as 7860 kg m−37860\ \text{kg m}^{-3}, its ultimate tensile strength as 400 MPa400\ \text{MPa} and its yield strength as 250 MPa250\ \text{MPa} (Table 8.1).

    What is the greatest speed of the rim before the ring breaks?

    MCQHard
    1 mark
  59. 59

    Question 59

    Wires of the same length, 1.0 m1.0\ \text{m}, are made of four metals from Table 8.1:

    MetalYY (GPa)σy\sigma_y (MPa)
    Aluminium7095
    Copper110200
    Wrought iron190170
    Steel200250

    Each wire is stretched until the stress just reaches its yield strength. Assuming each metal obeys Hooke's law up to that point, which wire stretches the most, and by how much?

    MCQHard
    1 mark
  60. 60

    Question 60

    Two steel plates overlap and are joined by four identical rivets, each of diameter 6.0 mm6.0\ \text{mm}. When the plates are pulled apart along their length, each rivet is sheared across one cross-section (the plane where the plates meet). The rivet metal can withstand a shearing stress of 6.9×107 N m−26.9 \times 10^{7}\ \text{N m}^{-2}, and the design uses a safety factor of 2 on this stress. The load is shared equally by the rivets.

    What is the greatest pulling force the joint may be designed to carry?

    MCQHard
    1 mark
  61. 61

    Question 61

    Blocks of mass 3.0 kg3.0\ \text{kg} and 5.0 kg5.0\ \text{kg} hang from the two ends of a light steel wire that passes over a light, frictionless pulley, and are released. The wire has a cross-sectional area of 1.0 mm21.0\ \text{mm}^2. Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2} and Ysteel=2.0×1011 N m−2Y_{\text{steel}} = 2.0 \times 10^{11}\ \text{N m}^{-2}.

    While the blocks are moving, what are the tensile stress and the longitudinal strain in the wire?

    MCQHard
    1 mark
  62. 62

    Question 62

    An aluminium wire of length 1.5 m1.5\ \text{m} and diameter 2.0 mm2.0\ \text{mm} carries a tensile load of 150 N150\ \text{N}. Take YAl=70 GPaY_{\text{Al}} = 70\ \text{GPa} and Poisson's ratio for aluminium as 0.330.33.

    By how much does the diameter of the wire decrease, and by what fraction does its cross-sectional area decrease?

    MCQHard
    1 mark
  63. 63

    Question 63

    Sizing the cables of a suspension bridge. The deck of a suspension bridge hangs from two main steel cables, one on each side. The deck and its heaviest traffic together weigh 2.0×107 N2.0 \times 10^{7}\ \text{N}. In a first, simplified estimate the engineers assume that each cable carries half of this load and that the tension is the same all along the cable. Each main cable is 1000 m1000\ \text{m} long. For steel take Y=2.0×1011 N m−2Y = 2.0 \times 10^{11}\ \text{N m}^{-2}, ultimate strength σu=400 MPa\sigma_u = 400\ \text{MPa}, yield strength σy=250 MPa\sigma_y = 250\ \text{MPa} and density 7860 kg m−37860\ \text{kg m}^{-3} (Table 8.1). The design uses a safety factor of 3 on the ultimate strength.

    Class 11 Physics Mechanical Properties Of Solids

    (i) Find the cross-sectional area and the diameter of each main cable.

    (ii) Each cable is actually made of parallel steel wires of diameter 5.0 mm5.0\ \text{mm}. About how many wires does each cable need?

    (iii) Find the working stress in a cable, and show that the cable stays within its elastic limit.

    (iv) By how much does each 1000 m1000\ \text{m} cable stretch at the working load, and how much elastic energy does it then store?

    (v) An engineer suggests aluminium cables instead (σu=110 MPa\sigma_u = 110\ \text{MPa}, Y=70 GPaY = 70\ \text{GPa}, density 2710 kg m−32710\ \text{kg m}^{-3}), with the same safety factor. Find the area needed and compare the mass of one metre of cable with that of steel. Is aluminium the better choice?

    Hard
    5 marks
  64. 64

    Question 64

    Why concrete columns carry steel bars. A building column of height 3.0 m3.0\ \text{m} has a square cross-section 0.30 m×0.30 m0.30\ \text{m} \times 0.30\ \text{m}. Four steel bars, each of diameter 2.5 cm2.5\ \text{cm}, run along its full length, firmly bonded to the concrete, as shown. The column carries a compressive load of 1.0×106 N1.0 \times 10^{6}\ \text{N} spread evenly over its top. Take Yconcrete=30 GPaY_{\text{concrete}} = 30\ \text{GPa} and Ysteel=200 GPaY_{\text{steel}} = 200\ \text{GPa} (Table 8.1), and the ultimate compressive strength of concrete as 40 MPa40\ \text{MPa}.

    Class 11 Physics Mechanical Properties Of Solids

    (i) Find the cross-sectional area of the steel and of the concrete.

    (ii) Explain why the steel and the concrete have the same strain, and find this strain.

    (iii) Find the compressive stress in the concrete and in the steel.

    (iv) What percentage of the load do the steel bars carry, although they make up only a small part of the cross-section?

    (v) By how much does the column shorten? Compare the shortening and the safety factor of the concrete with those of a plain concrete column of the same size carrying the same load.

    Hard
    5 marks
  65. 65

    Question 65

    Reading a tensile test. A metal specimen is pulled in a testing machine and its stress–strain curve is recorded, as shown (part (b) enlarges the start of the curve). The straight part OB has a slope of Y=200 GPaY = 200\ \text{GPa} and ends at B (strain 0.001250.00125, stress 250 MPa250\ \text{MPa}). Between B and C (strain 0.0200.020, stress 300 MPa300\ \text{MPa}) the curve may be taken as a straight line. The highest point D is at a stress of 400 MPa400\ \text{MPa} (strain 0.120.12), and the specimen breaks at E (strain 0.180.18, stress 330 MPa330\ \text{MPa}). When the load is removed from any point beyond B, the specimen unloads along a straight line parallel to OB, and if it is loaded again it goes back up along that same line until it rejoins the original curve.

    Class 11 Physics Mechanical Properties Of Solids

    (i) State the yield strength and the ultimate tensile strength of the metal, and check that the slope of OB agrees with Y=200 GPaY = 200\ \text{GPa}.

    (ii) A second specimen is loaded only up to C and then unloaded completely. How much of its strain does it recover, and what permanent set is left?

    (iii) This second specimen is now loaded again. Up to what stress does it now behave elastically, and what is its Young's modulus during this reloading? Has the treatment made the metal stiffer, or only raised its elastic limit?

    (iv) A third specimen is loaded only to 200 MPa200\ \text{MPa} and unloaded. What strain does it recover, and what permanent set does it have?

    (v) Is the metal brittle or ductile? Give two pieces of evidence from the curve, and say why such a metal suits a car body panel better than glass would.

    Hard
    5 marks
  66. 66

    Question 66

    Choosing a floor beam. A timber beam of span 4.0 m4.0\ \text{m}, breadth b=0.10 mb = 0.10\ \text{m} and depth d=0.30 md = 0.30\ \text{m} rests on supports at its ends and carries a load of W=1.0×104 NW = 1.0 \times 10^{4}\ \text{N} at its centre, as shown. The sag of such a beam is δ=Wl34bd3Y\delta = \dfrac{Wl^3}{4bd^3Y}. For timber take Y=13 GPaY = 13\ \text{GPa} and density 525 kg m−3525\ \text{kg m}^{-3}; for steel Y=200 GPaY = 200\ \text{GPa} and density 7860 kg m−37860\ \text{kg m}^{-3} (Table 8.1). Ignore the weight of the beams themselves.

    Class 11 Physics Mechanical Properties Of Solids

    (i) Find the sag of the timber beam.

    (ii) A building code limits the sag of a floor beam to 1/3601/360 of its span. What is the largest central load the timber beam may carry?

    (iii) A solid rectangular steel beam of breadth 0.050 m0.050\ \text{m} is to replace the timber one and sag by the same amount under the same load. What depth must it have?

    (iv) Compare the masses of one metre of the two beams. Which beam is lighter for the same stiffness?

    (v) Steel beams are usually made with an I-shaped cross-section rather than as solid rectangles. Explain the advantage, and why the depth cannot simply be increased while the beam is made thinner and thinner.

    Hard
    5 marks
  67. 67

    Question 67

    A steel wire of length 3.0 m3.0\ \text{m} and cross-sectional area 2.0 mm22.0\ \text{mm}^2 hangs from a rigid support. Take Y=2.0×1011 N m−2Y = 2.0 \times 10^{11}\ \text{N m}^{-2}, yield strength σy=250 MPa\sigma_y = 250\ \text{MPa} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}. A 35 kg35\ \text{kg} block is attached to its lower end.

    (a) The block is lowered gently by hand until the wire supports it on its own. Find the extension and the stress in the wire.

    (b) Instead, the block is attached while the wire is just unstretched and is released suddenly. Using energy conservation, find the greatest extension, and hence the greatest stress, assuming Hooke's law. What will actually happen to the wire?

    (c) What is the largest mass that may be released suddenly in this way without the wire taking a permanent set? Compare it with the largest mass that may be lowered gently.

    (d) In the gentle lowering of part (a), compare the loss of gravitational potential energy of the block with the elastic energy stored in the wire, and explain the difference.

    Hard
    4 marks
  68. 68

    Question 68

    A steel wire is stretched so that the tensile stress in it is 2.0×108 N m−22.0 \times 10^{8}\ \text{N m}^{-2}. Take Y=2.0×1011 N m−2Y = 2.0 \times 10^{11}\ \text{N m}^{-2}, Poisson's ratio 0.300.30 and the density of unstretched steel 7860 kg m−37860\ \text{kg m}^{-3}.

    (a) Find the longitudinal strain and the lateral strain.

    (b) Show that the fractional change in the volume of the wire is ΔVV=ΔLL(1−2σP)\dfrac{\Delta V}{V} = \dfrac{\Delta L}{L}(1 - 2\sigma_P), where σP\sigma_P is Poisson's ratio, and evaluate it.

    (c) Find the density of the stretched steel. For what value of Poisson's ratio would stretching not change the density at all?

    Hard
    3 marks
  69. 69

    Question 69

    A person of mass 70 kg70\ \text{kg} jumps down from a wall and lands stiff-legged on both feet, hitting the ground at 3.0 m s−13.0\ \text{m s}^{-1} and coming to rest in 0.050 s0.050\ \text{s}. Assume the force from the ground is constant during this time and is shared equally by the two shin bones (tibias). Model each tibia as a solid cylinder of length 0.40 m0.40\ \text{m} and radius 1.5 cm1.5\ \text{cm}. For bone take Y=9.4×109 N m−2Y = 9.4 \times 10^{9}\ \text{N m}^{-2} and ultimate compressive strength 170 MPa170\ \text{MPa} (Table 8.1); g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    (a) Find the force exerted by the ground on the person during the landing.

    (b) Find the compressive stress and strain in each tibia, and its shortening.

    (c) What is the safety factor of the tibia against fracture in this landing? Why do people bend their knees on landing?

    Hard
    3 marks
  70. 70

    Question 70

    A syringe with its nozzle sealed contains 10.0 cm310.0\ \text{cm}^3 of liquid and no air. Its plunger has a cross-sectional area of 1.0 cm21.0\ \text{cm}^2. Treat the syringe walls and plunger as rigid, and use the bulk moduli of Table 8.3: glycerine 4.76 GPa4.76\ \text{GPa}, water 2.2 GPa2.2\ \text{GPa}, carbon disulphide 1.56 GPa1.56\ \text{GPa}.

    (a) The plunger is pushed in by 0.12 mm0.12\ \text{mm}. Find the change in volume and the volume strain of the liquid.

    (b) Find the force needed on the plunger to do this when the syringe holds glycerine, water and carbon disulphide in turn.

    (c) Use your results to explain why the brakes and jacks of hydraulic systems use liquids, and why an air bubble in a brake line is dangerous.

    Hard
    3 marks
  71. 71

    Question 71

    A solid steel rod of radius 1.0 cm1.0\ \text{cm} and a steel tube of outer radius 2.0 cm2.0\ \text{cm} have the same cross-sectional area of metal and the same length, 2.0 m2.0\ \text{m}. Take Ysteel=2.0×1011 N m−2Y_{\text{steel}} = 2.0 \times 10^{11}\ \text{N m}^{-2}.

    (a) Find the inner radius of the tube.

    (b) Each is pulled along its length by a force of 2.0×104 N2.0 \times 10^{4}\ \text{N}. Find the stress in each and the extension of each.

    (c) Used instead as a beam, supported at its ends and loaded at the middle, the tube sags much less than the rod. Explain why, although in part (b) the two behaved identically.

    Hard
    3 marks
  72. 72

    Question 72

    A punch press makes a circular hole of diameter 1.0 cm1.0\ \text{cm} in a steel plate 2.0 mm2.0\ \text{mm} thick by shearing out a disc. The steel fails in shear when the shearing stress reaches 3.0×108 N m−23.0 \times 10^{8}\ \text{N m}^{-2}.

    (a) Identify the surface over which the steel is sheared, and find its area.

    (b) Find the least force the punch must apply.

    (c) A student uses the area of the hole, πr2\pi r^2. What force does she get, and why is it wrong? How does the correct force change if the plate thickness is doubled?

    Hard
    3 marks
  73. 73

    Question 73

    A uniform wire hangs vertically from its top end, with nothing attached below. Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2} and, from Table 8.1, for steel σu=400 MPa\sigma_u = 400\ \text{MPa}, σy=250 MPa\sigma_y = 250\ \text{MPa} and ρ=7860 kg m−3\rho = 7860\ \text{kg m}^{-3}.

    (a) Where along the wire is the stress greatest? Find the greatest length of steel wire that can hang without breaking.

    (b) Find the greatest length of steel wire that can hang without taking a permanent set.

    (c) Would a thicker steel wire allow a greater length in (a) or (b)? Explain.

    Hard
    3 marks
  74. 74

    Question 74

    Two rods, P and Q, one of glass and one of copper, have lost their labels. Tests in a laboratory give the following data.

    RodStraight-line region ends atGreatest stressBreaks at
    Pstress 50 MPa50\ \text{MPa}, strain 7.7×10−47.7 \times 10^{-4}50 MPa50\ \text{MPa}stress 50 MPa50\ \text{MPa}, strain 7.7×10−47.7 \times 10^{-4}
    Qstress 200 MPa200\ \text{MPa}, strain 1.82×10−31.82 \times 10^{-3}400 MPa400\ \text{MPa} at strain 0.250.25stress 360 MPa360\ \text{MPa}, strain 0.450.45

    (a) Find the Young's modulus of each rod and use Table 8.1 (glass 65 GPa65\ \text{GPa}, copper 110 GPa110\ \text{GPa}) to identify them.

    (b) Classify each material as brittle or ductile, giving reasons from the data.

    (c) Which rod would be suitable for drawing into a thin wire, and why?

    Hard
    3 marks
  75. 75

    Question 75

    A wire of length LL and cross-sectional area AA stretches by ΔL\Delta L when a load WW hangs from it. The wire is now folded in half to make a double strand of length L/2L/2, and the same load WW hangs from the fold, shared equally by the two halves.

    (a) What is the new extension, in terms of ΔL\Delta L?

    (b) How do the stress in the wire and the largest load the arrangement can hold without breaking compare with the original?

    Hard
    2 marks
  76. 76

    Question 76

    A concrete beam rests on supports at its two ends and carries a load at its middle, so it sags slightly. Steel bars are cast into it to strengthen it.

    (a) Which face of the beam, top or bottom, is stretched as it sags, and which is squeezed?

    (b) Explain why the steel bars are placed near the lower face of the beam rather than along its middle or near its top.

    Hard
    2 marks
  77. 77

    Question 77

    In mechanics we often treat a steel bar as a "rigid body". A steel bar 1.0 m1.0\ \text{m} long with a cross-sectional area of 1.0 cm21.0\ \text{cm}^2 is squeezed between the jaws of a press with a force of 10 kN10\ \text{kN}. Take Ysteel=2.0×1011 N m−2Y_{\text{steel}} = 2.0 \times 10^{11}\ \text{N m}^{-2} and its yield strength as 250 MPa250\ \text{MPa}.

    (a) Find the stress in the bar and by how much the bar shortens.

    (b) Describe one situation in which this change in length can safely be ignored, so that the bar may be treated as rigid, and one in which it cannot.

    Hard
    2 marks
  78. 78

    Question 78

    Dry sand poured from a height always forms a conical heap whose sides make the same angle with the ground, however much sand is poured.

    (a) Explain why the angle of the sides does not depend on the size of the heap.

    (b) A second heap of the same sand is made twice as tall. How do its base radius, its volume and its weight compare with those of the first heap?

    Hard
    2 marks
  79. 79

    Question 79

    A railway rail, seen in cross-section, has a head at the top, a thin vertical web, and a wide flat foot at the bottom that rests on the sleepers.

    (a) How does the wide foot protect the sleepers under the heavy wheel loads?

    (b) Why would a rail with a foot only as wide as its web be unsafe, even if it were strong enough?

    Hard
    2 marks
  80. 80

    Question 80

    Table 8.1 shows that metals such as steel have Young's moduli of the order of 1011 N m−210^{11}\ \text{N m}^{-2}, while elastomers such as rubber can be stretched to several times their length by quite small stresses.

    (a) Explain the large Young's modulus of a metal in terms of what happens to its atoms when it is stretched.

    (b) Explain why an elastomer can take such large strains and still return to its original length.

    Hard
    2 marks