Confirming your payment

Skip to content

Opening your dashboard

Class 10 Physics Chapter 11 Electricity: Competency-Based Questions (CBQ)

80 questions on Chapter 11, each worked through on its own page with the AI tutor. Class 10 Physics, CBSE 2026-27.

80 questions

1–5 marks · Mixed difficulty

  1. 1

    Question 1

    Two wires P and Q are made of the same metal. Q is twice as long as P and has three times its area of cross-section. The two wires are connected in parallel across the same cell.

    Which statement about the currents is correct?

    MCQMedium
    1 mark
  2. 2

    Question 2

    A 1.2 kW1.2\ \text{kW} electric iron is to be used on a 220 V220\ \text{V} supply. Fuses are available with ratings of 3 A3\ \text{A}, 5 A5\ \text{A}, 10 A10\ \text{A} and 15 A15\ \text{A}.

    Which fuse is the most suitable for the iron?

    MCQMedium
    1 mark
  3. 3

    Question 3

    The same resistor is used in four experiments. In which experiment is the most heat produced?

    MCQMedium
    1 mark
  4. 4

    Question 4

    Read the following and answer all the sub-questions.

    Every house has a distribution board. The supply is divided into separate circuits, and each circuit has its own miniature circuit breaker (MCB), which cuts the supply if the current becomes too large. The ratings are not all the same.

    a household distribution board

    Three of the circuits on this board are listed below.

    CircuitWhat it suppliesMCB rating
    1ceiling lights and fans6 A
    2wall sockets16 A
    3air conditioner20 A

    The mains supply is 220 V.

    (a) Calculate the maximum power that circuit 2 can carry before its MCB trips. [1]

    (b) Suggest why the lighting circuit is given a much lower rating than the air-conditioner circuit. [1]

    (c) Circuit 3's MCB keeps tripping. The householder asks the electrician to fit a 32 A one instead. The electrician refuses. Explain why, and state what he should do instead. [2]

    Medium
    4 marks
  5. 5

    Question 5

    A copper connecting wire is to be replaced by an aluminium wire of the same length and the same resistance. The resistivities in NCERT Table 11.2 are: copper 1.62×10−8 Ω1.62 \times 10^{-8}\ \Omega m, aluminium 2.63×10−8 Ω2.63 \times 10^{-8}\ \Omega m.

    How must the aluminium wire compare with the copper wire?

    MCQMedium
    1 mark
  6. 6

    Question 6

    A 100 W100\ \text{W} bulb and a 25 W25\ \text{W} bulb are both rated for 220 V220\ \text{V}. Their filaments are made of the same metal and have the same length.

    Which bulb has the thicker filament?

    MCQMedium
    1 mark
  7. 7

    Question 7

    A 5 Ω5\ \Omega resistor and an unknown resistor RR are connected in series across a 12 V12\ \text{V} battery. An ammeter in the circuit reads 0.8 A0.8\ \text{A}.

    What is the value of RR?

    MCQMedium
    1 mark
  8. 8

    Question 8

    A student has a number of identical resistors. By connecting them in different ways, she finds that the largest equivalent resistance she can obtain is exactly 25 times the smallest.

    How many resistors does she have?

    MCQMedium
    1 mark
  9. 9

    Question 9

    Cell X does 15 J15\ \text{J} of work in moving 3 C3\ \text{C} of charge round a circuit. Cell Y does 16 J16\ \text{J} of work in moving 4 C4\ \text{C} round another circuit.

    Which statement is correct?

    MCQMedium
    1 mark
  10. 10

    Question 10

    A 60 W60\ \text{W}, 220 V220\ \text{V} bulb is used on its rated voltage for one hour.

    About how much charge passes through its filament in that time?

    MCQMedium
    1 mark
  11. 11

    Question 11

    A shop sells two electric kettles. Both are tested by boiling the same 1 litre of water from the same starting temperature.

    KettlePower ratingTime taken to boil
    A1 kW6 minutes
    B2 kW3 minutes

    (a) Show by calculation that the two kettles use the same amount of electrical energy to do this job. [1]

    (b) Electricity costs ₹6 per unit. How much does one boil cost with each kettle? [1]

    (c) If the two cost the same to run, suggest why a family might still choose kettle B — and state what the power rating actually tells you. [1]

    Medium
    3 marks
  12. 12

    Question 12

    A student measures the resistance of different lengths cut from one reel of wire. (Hypothetical data.)

    Length (m)0.51.01.5
    Resistance (Ω\Omega)1.22.43.6

    (a) Show from the data how the resistance depends on the length. [1]

    (b) What length of this wire would have a resistance of 6.0 Ω6.0\ \Omega? [1]

    (c) Explain why the resistance per metre is the same for every piece. [1]

    Medium
    3 marks
  13. 13

    Question 13

    A bulb is rated "60 W, 220 V". It is taken abroad and connected to a 110 V supply instead.

    Assuming its resistance does not change, what power does it now consume?

    MCQEasy
    1 mark
  14. 14

    Question 14

    A family lists four appliances with their power ratings and how long each is used every day.

    AppliancePowerUsed for
    LED lamp10 W6 hours
    Ceiling fan75 W8 hours
    Television120 W4 hours
    Instant geyser2000 W15 minutes

    Which appliance consumes the most electrical energy in a day?

    MCQMedium
    1 mark
  15. 15

    Question 15

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): When a 2 Ω2\ \Omega resistor and a 4 Ω4\ \Omega resistor are connected in series to a 6 V6\ \text{V} battery, the potential difference across the 4 Ω4\ \Omega resistor is 4 V4\ \text{V}.

    Reason (R): In a series circuit, the potential difference across each resistor is proportional to its resistance.

    MCQEasy
    1 mark
  16. 16

    Question 16

    Read the following and answer all the sub-questions.

    The photograph shows a string of decorative lights. One bulb has failed — its filament is broken and it is dark — but the bulbs on either side of it are still glowing normally.

    a string of lights with one bulb failed

    (a) Are the bulbs in this string connected in series or in parallel? Justify your answer from the observation. [1]

    (b) A cheaper string behaves differently: when a single bulb fails, the whole string goes dark. How are its bulbs connected, and why does one failure stop them all? [1]

    (c) That cheaper string carries 20 identical bulbs and runs from the 220 V mains. Calculate the potential difference across each bulb when all 20 are working, and give two reasons why the lights in a house are wired the other way. [2]

    Medium
    4 marks
  17. 17

    Question 17

    Read the following and answer all the sub-questions.

    To save wire, an untrained helper connects a room heater rated 1100 W, 220 V and a bulb rated 100 W, 220 V in series across the 220 V220\,\text{V} mains, as shown in the figure. Treat the resistance of each appliance as constant.

    Class 10 Physics Electricity

    (a) Using the ratings, find the resistance of the heater and of the bulb. [1]

    (b) Find the current that flows when the series circuit is switched on. [1]

    (c) Find the power actually consumed by the heater in this circuit, and explain why the bulb glows almost normally while the heater hardly warms up. [1]

    (d) State how the two appliances should be connected to the mains, and give one reason why that arrangement lets each of them work properly. [1]

    Medium
    4 marks
  18. 18

    Question 18

    A household's electricity meter read 4512 units on 1 September and 4785 units on 30 September.

    (a) How many units were consumed during September? [1]

    (b) Electricity is charged at ₹6.50 per unit. Calculate the bill for the month. [1]

    (c) The family wants to cut next month's bill by 10%. Their 2 kW geyser currently runs for 1 hour every day. By how many minutes a day must they reduce its use to achieve this? Take the month as 30 days and assume everything else stays the same. [1]

    Medium
    3 marks
  19. 19

    Question 19

    The insulation on an old appliance cord has frayed, and the live and neutral wires inside it touch each other directly.

    (a) State what happens to the resistance of the path between live and neutral when this occurs, and why. [1]

    (b) Using Ohm's law, explain what then happens to the current in the circuit. [1]

    (c) Explain how a fuse prevents this from starting a fire, and state why the fuse must be rated lower than the safe current of the household wiring. [1]

    Medium
    3 marks
  20. 20

    Question 20

    Assertion: A 100 W100\,W bulb glows brighter than a 60 W60\,W bulb when connected to the same voltage source.
    Reason: The resistance of the 100 W100\,W bulb is lower than that of the 60 W60\,W bulb.

    MCQMedium
    1 mark
  21. 21

    Question 21

    A student records these readings for a resistor. (Hypothetical data.)

    Potential difference (V)1.02.03.04.0
    Current (A)0.250.500.701.00

    (a) Find the resistance of the resistor. [1]

    (b) One reading does not fit. Identify it, and state what the current should have been. [1]

    Medium
    2 marks
  22. 22

    Question 22

    A wire has resistance RR. A second wire is made of a metal with twice the resistivity, and has half the length and half the area of cross-section of the first.

    What is the resistance of the second wire?

    MCQMedium
    1 mark
  23. 23

    Question 23

    A 100 Ω100\ \Omega resistor and a 400 Ω400\ \Omega resistor are each rated at 1 W1\ \text{W}, the most power they can safely handle. They are connected in series to a variable supply.

    (a) Find the largest current each resistor can safely carry on its own. [1]

    (b) What is the largest current that may flow in the series circuit? Give a reason. [1]

    (c) Find the largest supply voltage that can be used. [1]

    Medium
    3 marks
  24. 24

    Question 24

    Assertion: In a parallel circuit, adding more resistors increases the total current drawn from the source.
    Reason: In a parallel circuit, the equivalent resistance decreases with the addition of more resistors.

    MCQMedium
    1 mark
  25. 25

    Question 25

    Three identical bulbs, each of resistance 12 Ω12\ \Omega, are connected in parallel. This group is connected in series with a 2 Ω2\ \Omega resistor to a battery. The current through each bulb is found to be 13 A\dfrac{1}{3}\ \text{A}.

    Class 10 Physics Electricity

    (a) Find the potential difference across the bulbs. [1]

    (b) Find the current drawn from the battery. [1]

    (c) Find the potential difference of the battery. [1]

    Medium
    3 marks
  26. 26

    Question 26

    A 2 kW room heater is currently used for 4 hours every day.

    Which of the following changes, on its own, would halve the electrical energy it consumes in a day?

    • P: running it at half the power, for the same 4 hours
    • Q: running it at the same power, for 2 hours instead of 4
    MCQMedium
    1 mark
  27. 27

    Question 27

    In one minute, 3×10203 \times 10^{20} electrons pass through a cross-section of a wire. The charge on an electron is 1.6×10−19 C1.6 \times 10^{-19}\ \text{C}.

    What is the current in the wire?

    MCQMedium
    1 mark
  28. 28

    Question 28

    A copper wire and an iron wire of the same length and the same area of cross-section are connected in series to a battery. The resistivities in NCERT Table 11.2 are: copper 1.62×10−8 Ω1.62 \times 10^{-8}\ \Omega m, iron 10.0×10−8 Ω10.0 \times 10^{-8}\ \Omega m.

    What is the ratio of the potential difference across the iron wire to that across the copper wire?

    MCQEasy
    1 mark
  29. 29

    Question 29

    A battery gives 18 J18\ \text{J} of energy to every 3 C3\ \text{C} of charge that passes through it. It drives a current of 0.5 A0.5\ \text{A} for 22 minutes.

    How much energy does it supply in this time?

    MCQMedium
    1 mark
  30. 30

    Question 30

    A resistor obeys Ohm's law. When the potential difference across it is increased by 3 V3\ \text{V}, the current through it increases by 0.25 A0.25\ \text{A}.

    (a) Find the resistance. [1]

    (b) The current was 0.5 A0.5\ \text{A} before the increase. Find the potential difference before and after the increase. [1]

    (c) Explain why the change in VV and the change in II are enough to find RR, without knowing the starting values. [1]

    Medium
    3 marks
  31. 31

    Question 31

    A torch bulb works normally at 3 V3\ \text{V} and 0.3 A0.3\ \text{A}. Two such bulbs are connected in series to the same 3 V3\ \text{V} cell. Treat the bulbs' resistance as constant.

    (a) Find the current in the circuit. [1]

    (b) Will the bulbs glow normally? Give a reason. [1]

    Easy
    2 marks
  32. 32

    Question 32

    Two lamps L1L_1 and L2L_2 are connected in parallel to a 6 V6\ \text{V} battery. Ammeter A1A_1 is in the main wire from the battery, ammeter A2A_2 is in the branch with L1L_1, and ammeter A3A_3 is in the branch with L2L_2. A2A_2 reads 0.4 A0.4\ \text{A} and A3A_3 reads 0.6 A0.6\ \text{A}.

    (a) What does A1A_1 read? [1]

    (b) Which lamp has the larger resistance, and by what factor? [1]

    (c) Find the resistance of each lamp. [1]

    Medium
    3 marks
  33. 33

    Question 33

    Points A, B and C lie in that order along a conducting path. Moving 2 C2\ \text{C} of charge from A to B takes 10 J10\ \text{J} of work, and moving 4 C4\ \text{C} from B to C takes 12 J12\ \text{J}.

    (a) Find the potential difference between A and B, and between B and C. [1]

    (b) Find the work needed to move 3 C3\ \text{C} from A to C. [1]

    Medium
    2 marks
  34. 34

    Question 34

    Lamp P is rated 60 W,220 V60\ \text{W}, 220\ \text{V} and lamp Q is rated 60 W,110 V60\ \text{W}, 110\ \text{V}. Which lamp has the larger resistance, and by what factor?

    Medium
    1 mark
  35. 35

    Question 35

    The rating plate on an electric heater reads "1500 W, 230 V".

    (a) State what the two numbers mean taken together. [1]

    (b) Calculate the current the heater draws and its resistance when it is working normally. [1]

    (c) The heater is taken to a country whose mains supply is 115 V. Will it deliver 1500 W there? Support your answer with a calculation. [1]

    Medium
    3 marks
  36. 36

    Question 36

    A student tests two components, X and Y. (Hypothetical data.)

    Potential difference (V)1.02.03.0
    Current in X (A)0.100.200.30
    Current in Y (A)0.100.150.18

    (a) Find VI\dfrac{V}{I} for each reading of X and of Y. [1]

    (b) Which component obeys Ohm's law? Give a reason. [1]

    (c) Predict the current in the component that obeys Ohm's law when the potential difference is 4.5 V4.5\ \text{V}. [1]

    Medium
    3 marks
  37. 37

    Question 37

    An appliance is marked "1100 W, 220 V" and is connected to a 220 V mains supply.

    Three of the following statements about it are correct. Which one is NOT?

    MCQMedium
    1 mark
  38. 38

    Question 38

    Study the following circuit and find:

    Class 10 Physics Electricity

    (i) Effective resistance of the circuit.

    (ii) Current drawn from the battery.

    (iii) Potential difference across the 5Ω5 \Omega resistor.

    Medium
    3 marks
  39. 39

    Question 39

    A man is deciding between buying electricity from the Main Board (at ₹3.50 per kWh) or using his own generator, which has a maximum power of 2.0 kW and runs at this power for 3 hours.

    (a) Calculate how much it would cost him to buy the same amount of energy the generator produced, from the Main Electricity Board.

    (b) A student boils water in an electric kettle for 20 minutes on the same mains supply and wants to reduce the boiling time. Should he increase or decrease the length of the heating element? Justify your answer.

    Medium
    3 marks
  40. 40

    Question 40

    A current of 5 A5\ \text{A} enters a junction and divides between a 4 Ω4\ \Omega resistor and a 6 Ω6\ \Omega resistor connected in parallel.

    (a) Find the potential difference across the pair. [1]

    (b) Find the current in each resistor. [1]

    (c) The 6 Ω6\ \Omega resistor is replaced by a 12 Ω12\ \Omega resistor, and the total current is kept at 5 A5\ \text{A}. Find the new current in the 4 Ω4\ \Omega resistor. [1]

    Medium
    3 marks
  41. 41

    Question 41

    A small workshop is supplied at 220 V220\,\text{V} and its circuit is protected by a fuse rated 5 A5\,\text{A}. The owner runs a 400 W400\,\text{W} drill and a 600 W600\,\text{W} bank of lamps at the same time, both connected in parallel across the supply.

    (a) Calculate the current drawn by each of the two, and the total current.

    (b) Will the fuse carry this load safely? Justify your answer.

    (c) He now switches on a 500 W500\,\text{W} heater as well. Show by calculation what happens.

    (d) State one thing he should do so that all three can run safely.

    Hard
    4 marks
  42. 42

    Question 42

    In the circuit shown, the ammeter reads 0.50 A0.50\ \text{A} while switch S is open. When S is closed, the reading rises to 0.75 A0.75\ \text{A}.

    Class 10 Physics Electricity

    (a) Find the resistance of R2R_2. [2]

    (b) R2R_2 is now taken out of the switch branch and connected in series with R1R_1 instead. Predict the new ammeter reading. [1]

    Medium
    3 marks
  43. 43

    Question 43

    Read the following and answer all the sub-questions.

    A 2200 W,220 V2200\ \text{W}, 220\ \text{V} room heater is used at the end of a long extension cable. The cable has two copper conductors, each 25 m25\ \text{m} long with an area of cross-section of 1.0 mm21.0\ \text{mm}^2, so the current travels through 50 m50\ \text{m} of copper in all. The resistivity of copper is 1.62×10−8 Ω m1.62 \times 10^{-8}\ \Omega\,\text{m}. The supply is 220 V220\ \text{V}. Treat the heater's resistance as constant.

    (a) Find the resistance of the cable and of the heater. [1]

    (b) Find the current that flows. [1]

    (c) Find the potential difference across the heater and the power it actually produces. [1]

    (d) Find the heat produced in the cable each second, and explain why a coiled-up extension cable can become dangerously hot. [1]

    (e) What is the smallest area of cross-section that would keep the drop in the cable to 2.2 V2.2\ \text{V} (1% of the supply) when a current of 10 A10\ \text{A} flows? [1]

    Hard
    5 marks
  44. 44

    Question 44

    An electric oven contains two identical heating coils, each of resistance 44 Ω44\ \Omega. A switch lets the user connect them either in series or in parallel across the same 220 V220\ \text{V} mains supply.

    (a) Calculate the total power of the oven in the series arrangement. [1]

    (b) Calculate the total power in the parallel arrangement. [1]

    (c) State which setting is "high" and which is "low", and by what factor they differ. Explain, in terms of resistance and current, why connecting the coils in parallel gives more heat rather than less. [2]

    Medium
    4 marks
  45. 45

    Question 45

    Read the following and answer all the sub-questions.

    An electric immersion rod marked "1500 W, 220 V" is used to heat water in a bucket. The heating element is a long coil of nichrome wire; the flexible cord that carries the current to it is thick copper.

    an immersion rod in a bucket of water

    (a) Calculate the current the rod draws and the resistance of its element in normal use. [1]

    (b) Exactly the same current flows through the copper cord and through the nichrome element, yet only the element becomes red hot. Explain why. [1]

    (c) To save money, a shopkeeper fits a cheaper, thinner cord whose total resistance is 0.5 Ω0.5\,\Omega. Taking the current to be unchanged, calculate the heat produced in this cord in one minute, and the power wasted in it. Explain why this cord is unsafe even though the rod still works. [1]

    (d) The rod is switched on by mistake while it is lying on the floor, out of the water, and it burns out within a minute. It still produces heat at the same rate as in water. Explain why it burns out. [2]

    Medium
    5 marks
  46. 46

    Question 46

    Electrical power is carried from a generating station to a village along a cable whose total resistance is 2 Ω2\ \Omega. In one arrangement the cable carries a current of 10 A10\ \text{A}.

    (a) Calculate the power wasted as heat in the cable itself. [1]

    (b) The same power is now delivered to the village at ten times the voltage, so that the current in the cable is only 1 A1\ \text{A}. Calculate the power now wasted in the cable. [1]

    (c) State the factor by which the waste has fallen, and explain why power is transmitted over long distances at very high voltage. [2]

    Medium
    4 marks
  47. 47

    Question 47

    A lamp is rated 6 V,3 W6\ \text{V}, 3\ \text{W}. It has to be run at its normal brightness from a 9 V9\ \text{V} battery.

    (a) Find the resistance that must be connected in series with the lamp. [2]

    (b) What fraction of the power drawn from the battery is wasted in this resistor? [1]

    Medium
    3 marks
  48. 48

    Question 48

    A rectangular copper block measures 1 cm×2 cm×4 cm1\ \text{cm} \times 2\ \text{cm} \times 4\ \text{cm}. Its resistance is measured between different pairs of opposite faces.

    (a) Between which pair of faces is the resistance greatest? [1]

    (b) By what factor is the greatest resistance larger than the smallest? [1]

    Medium
    2 marks
  49. 49

    Question 49

    Two resistors give an equivalent resistance of 9 Ω9\ \Omega when joined in series and 2 Ω2\ \Omega when joined in parallel. Find the two resistances. [2]

    Medium
    2 marks
  50. 50

    Question 50

    A household's 15 A circuit is protected by a 15 A fuse on the 220 V220\,\text{V} mains. A 2000 W heater, a 750 W iron and five 100 W bulbs are all connected in parallel on this circuit, as shown.

    Class 10 Physics Electricity

    (a) Calculate the total current drawn when all of them are switched on. [1]

    (b) Will the fuse allow this? Could even one more 100 W bulb be switched on without the fuse blowing? Show your working. [1]

    (c) The heater is now switched off. What is the largest number of 100 W bulbs that can be on together with the iron without the fuse blowing? [1]

    (d) The family wants to move the heater to a separate circuit protected by a 5 A fuse. Will the heater work on that circuit? Explain. [1]

    Hard
    4 marks
  51. 51

    Question 51

    A student tests two resistors on their own and then joined together, first in series and then in parallel. She plots all four sets of readings on one graph, with potential difference on the vertical axis.

    Class 10 Physics Electricity

    Lines Q and R belong to the two resistors on their own. At a current of 0.5 A0.5\ \text{A}, line Q reads 3 V3\ \text{V} and line R reads 1.5 V1.5\ \text{V}. What does the line for the parallel combination read at 0.5 A0.5\ \text{A}?

    MCQMedium
    1 mark
  52. 52

    Question 52

    A student measures the resistance RR of several wires made of the same metal and of the same length, but with different areas of cross-section AA and diameters dd. She wants a graph that is a straight line through the origin.

    What should she plot?

    MCQMedium
    1 mark
  53. 53

    Question 53

    A heater is to be made to work at 1100 W1100\ \text{W} on a 220 V220\ \text{V} supply, using a heating alloy wire of resistivity 1.0×10−6 Ω m1.0 \times 10^{-6}\ \Omega\,\text{m} and area of cross-section 1.0×10−7 m21.0 \times 10^{-7}\ \text{m}^2.

    (a) Find the resistance the element must have, and the length of wire needed. [2]

    (b) The element runs too hot. The designer keeps 1100 W1100\ \text{W} on 220 V220\ \text{V} but uses wire of the same alloy with twice the area of cross-section. What length is needed now, and why does the new element run cooler? [2]

    Medium
    4 marks
  54. 54

    Question 54

    An electrician installs a fuse rated for a 5 A heater, but it keeps burning out even under normal load. He suspects the fuse wire itself is unsuitable.

    What change should he make to the fuse wire's construction to fix this?

    MCQMedium
    1 mark
  55. 55

    Question 55

    Read the following and answer all the sub-questions.

    A wall socket used for a 2000 W room heater has become scorched and partly melted around one of its pin holes. An electrician finds that the terminal screw behind that hole had worked loose, so the metal contact area there was very small. A loose contact of this kind behaves as an extra resistance of roughly 0.5 Ω0.5\ \Omega in series at the joint.

    The mains supply is 220 V.

    Class 10 Physics Electricity

    (a) Calculate the current drawn by the heater. [1]

    (b) Calculate the power dissipated at the loose joint. [1]

    (c) The heater itself dissipates 2000 W and does not melt, while the joint dissipates far less and chars the plastic around it. Explain this apparent contradiction. [2]

    (d) State what should be done about the socket. [1]

    Medium
    5 marks
  56. 56

    Question 56

    A resistor is connected to a battery for a certain time. It is then replaced by a resistor of twice the resistance, connected to a battery of twice the potential difference, for half the time.

    Compared with the first case, the heat produced is:

    MCQMedium
    1 mark
  57. 57

    Question 57

    In a school laboratory a student uses an ammeter whose scale runs from 00 to 3 A3\,\text{A} over 3030 equal divisions, and a voltmeter whose scale runs from 00 to 15 V15\,\text{V} over 3030 equal divisions.

    (a) Find the least count of each meter.

    (b) With a resistor connected, the ammeter needle rests on the 18th18^{\text{th}} division and the voltmeter needle on the 20th20^{\text{th}}. Calculate the resistance of the resistor.

    Medium
    3 marks
  58. 58

    Question 58

    A student puts a resistance coil in a fixed amount of water and passes different currents through it for 55 minutes each time, starting from the same temperature. (Hypothetical data.)

    Current (A)1.02.03.0
    Rise in temperature (°C)2.08.018.0

    (a) Show from the data how the heat produced depends on the current. [2]

    (b) Predict the rise in temperature for a current of 2.5 A2.5\ \text{A} for 55 minutes. [1]

    (c) Predict the rise for 2.0 A2.0\ \text{A} passed for 1010 minutes. [1]

    Hard
    4 marks
  59. 59

    Question 59

    Three identical lamps L1L_1, L2L_2 and L3L_3, each of resistance 8 Ω8\ \Omega, are connected in series with an ammeter across a 12 V12\ \text{V} battery.

    Class 10 Physics Electricity

    (a) Find the ammeter reading and the voltmeter reading across each lamp when all is working. [1]

    (b) On one day, a voltmeter reads 0 V0\ \text{V} across L1L_1 and 6 V6\ \text{V} across each of L2L_2 and L3L_3. Identify the fault, and state what the ammeter now reads. [2]

    (c) On another day, the voltmeter reads 12 V12\ \text{V} across L1L_1 and 0 V0\ \text{V} across the others, and no lamp glows. Identify the fault. [1]

    Hard
    4 marks
  60. 60

    Question 60

    A uniform wire of resistance 16 Ω16\ \Omega is bent into a complete circle.

    (a) Find the resistance between two points at opposite ends of a diameter. [2]

    (b) Find the resistance between two points a quarter of the circle apart. [1]

    Hard
    3 marks
  61. 61

    Question 61

    A heater coil of resistance 40 Ω40\ \Omega works on a 220 V220\ \text{V} supply. After a fault, two neighbouring turns touch, so that one quarter of the coil's length is short-circuited.

    (a) Calculate the power of the heater before and after the fault. [2]

    (b) Explain why this fault is dangerous even though the heater still works. [1]

    Hard
    3 marks
  62. 62

    Question 62

    Read the following and answer all the sub-questions.

    A student is given a wire of an unknown alloy, 50.0 cm50.0\ \text{cm} long and 0.40 mm0.40\ \text{mm} in diameter. She connects it in a circuit and records these readings. (Hypothetical data.)

    Potential difference (V)3.57.010.5
    Current (A)0.0200.0400.060

    Resistivities of some alloys at 20 °C, as given in NCERT Table 11.2:

    AlloyResistivity (Ω\Omega m)
    Constantan49×10−649 \times 10^{-6}
    Manganin44×10−644 \times 10^{-6}
    Nichrome100×10−6100 \times 10^{-6}

    (a) Show that the wire obeys Ohm's law, and find its resistance. [1]

    (b) Find the area of cross-section of the wire. [1]

    (c) Find the resistivity of the alloy. [1]

    (d) Identify the alloy. [1]

    (e) Predict the resistance of a 1.0 m1.0\ \text{m} length of the same alloy with a diameter of 0.80 mm0.80\ \text{mm}. [1]

    Hard
    5 marks
  63. 63

    Question 63

    Two resistors P and Q are each tested, and the results are plotted as a graph. Both give straight lines through the origin. Potential difference is plotted on the vertical axis and current on the horizontal axis, and the line for P is the steeper of the two.

    (a) State which resistor has the greater resistance, and explain how the resistance is read from a graph drawn with these axes. [1]

    (b) A second student plots the same two sets of readings the other way round, with current on the vertical axis and potential difference on the horizontal axis. Whose line is steeper now, and what does the slope represent? [2]

    (c) From the original graph, resistor P carries a current of 0.2 A0.2\ \text{A} when the potential difference across it is 6 V6\ \text{V}. Calculate its resistance. [1]

    Hard
    4 marks
  64. 64

    Question 64

    Assertion (A): A fuse is always connected in series with the appliance it protects.

    Reason (R): A fuse must carry the whole of the circuit current so that it melts and breaks the circuit when that current becomes dangerously large.

    MCQMedium
    1 mark
  65. 65

    Question 65

    A family replaces a 60 W60\ \text{W} filament bulb with a 9 W9\ \text{W} LED lamp that gives the same light. The lamp is used for 6 hours a day, and electricity costs ₹7 per unit. The LED lamp costs ₹100 more than the filament bulb.

    (a) How much money does the change save each day? [2]

    (b) After how many days has the LED lamp paid for its extra cost? [1]

    Hard
    3 marks
  66. 66

    Question 66

    A 6 Ω6\ \Omega resistor and an unknown resistor RR are connected in parallel. This combination is connected in series with a 4 Ω4\ \Omega resistor across a 12 V12\ \text{V} battery. The current in the 6 Ω6\ \Omega resistor is 1 A1\ \text{A}.

    (a) Find the total current drawn from the battery. [2]

    (b) Find RR. [1]

    Hard
    3 marks
  67. 67

    Question 67

    Assertion (A): A bulb rated "100 W, 220 V" consumes the same electrical energy when it is connected to a 110 V supply, provided it is left on for twice as long.

    Reason (R): The power dissipated by a bulb of fixed resistance is proportional to the square of the voltage applied across it.

    MCQHard
    1 mark
  68. 68

    Question 68

    A homeowner notices that his table lamp's bulb almost always fuses out the instant he switches it on, rather than while it has been glowing steadily for a while.

    What is the most likely reason for this?

    MCQMedium
    1 mark
  69. 69

    Question 69

    A student uses two resistors as a potential divider to run a lamp rated 3 V,0.5 A3\ \text{V}, 0.5\ \text{A} from a 12 V12\ \text{V} battery, as shown. Treat the lamp's resistance as constant.

    Class 10 Physics Electricity

    (a) Show that the potential difference across R2R_2 is 3 V3\ \text{V} before the lamp is connected. [1]

    (b) Find the potential difference across the lamp once it is connected. [2]

    (c) Suggest a new value of R1R_1 that would give the lamp its full 3 V3\ \text{V}. [1]

    Hard
    4 marks
  70. 70

    Question 70

    Three identical lamps L1L_1, L2L_2 and L3L_3, each of resistance 6 Ω6\ \Omega, are connected in series across an 18 V18\ \text{V} supply. Treat the lamps' resistances as constant.

    (a) Find the power of each lamp. [1]

    (b) A fourth identical lamp L4L_4 is now connected in parallel with L3L_3. Find the new power of L1L_1 and of L3L_3, and state how the brightness of each changes. [2]

    Hard
    3 marks
  71. 71

    Question 71

    Two 10 kΩ10\ \text{k}\Omega resistors are connected in series across a 12 V12\ \text{V} battery. A student connects a voltmeter across one of them, expecting it to read 6 V6\ \text{V}. The voltmeter itself has a resistance of 10 kΩ10\ \text{k}\Omega.

    (a) What does the voltmeter actually read? [2]

    (b) What would it read if its resistance were 1000 kΩ1000\ \text{k}\Omega instead? [1]

    Hard
    3 marks
  72. 72

    Question 72

    Three resistors X (4 Ω4\ \Omega), Y (4 Ω4\ \Omega) and Z (12 Ω12\ \Omega) are connected to a 14 V14\ \text{V} battery as shown.

    Class 10 Physics Electricity

    (a) X and Y have the same resistance. Which of them produces more heat, and why? [1]

    (b) Calculate the power in each of X, Y and Z. [2]

    (c) Z burns out and breaks the circuit through it. State, with calculation, what happens to the power in X and in Y. [1]

    Medium
    4 marks
  73. 73

    Question 73

    A student measures the current through a 4 Ω4\ \Omega resistor connected to a 5 V5\ \text{V} supply. Her ammeter has a resistance of 1 Ω1\ \Omega.

    (a) What current would flow without the ammeter, and what does the ammeter actually read? [2]

    (b) By what percentage is the reading too low? [1]

    (c) What is the largest ammeter resistance that would keep the reading within 1%1\% of the true value? [1]

    Hard
    4 marks
  74. 74

    Question 74

    To find the power of an old room heater whose label has worn off, a family switches off everything else in the house and runs only the heater. The electricity meter reading rises by 1.5 units in 45 minutes. The supply is 220 V220\ \text{V}.

    (a) Find the power of the heater. [1]

    (b) Find the current it draws. [1]

    (c) The house has a 5 A5\ \text{A} lighting circuit and a 15 A15\ \text{A} power circuit. On which should the heater be used? Give a reason. [1]

    Hard
    3 marks
  75. 75

    Question 75

    A technician has a large supply of resistors, but every one of them is 6 Ω6\ \Omega. Using only these, she has to build the following values.

    (a) Show, with a calculation, how to obtain exactly 3 Ω3\ \Omega. [1]

    (b) Show how to obtain exactly 9 Ω9\ \Omega. [1]

    (c) Show how to obtain exactly 4 Ω4\ \Omega. [1]

    (d) State the largest and the smallest resistance she could make from nn of these resistors. [1]

    Hard
    4 marks
  76. 76

    Question 76

    A student wants to verify Ohm's law for a 5 Ω5\ \Omega resistor using a 6 V6\ \text{V} battery, an ammeter, a voltmeter and a rheostat in series with the resistor. She wants readings starting from a current of 0.2 A0.2\ \text{A}.

    (a) What is the least full-scale resistance the rheostat must have? [2]

    (b) The resistor must not dissipate more than 5 W5\ \text{W}. What is the lowest setting of the rheostat she may use? [1]

    Hard
    3 marks
  77. 77

    Question 77

    Two branches are connected in parallel across a 12 V12\ \text{V} battery. One branch has 2 Ω2\ \Omega above 4 Ω4\ \Omega, meeting at point P; the other has 4 Ω4\ \Omega above 2 Ω2\ \Omega, meeting at point Q. An ideal voltmeter is connected between P and Q.

    Class 10 Physics Electricity

    (a) Find the current in each branch. [1]

    (b) Find the voltmeter reading, and state which of P and Q is at the higher potential. [2]

    (c) The resistors in the right-hand branch are swapped, so that it also has 2 Ω2\ \Omega above 4 Ω4\ \Omega. What does the voltmeter read now? [1]

    Hard
    4 marks
  78. 78

    Question 78

    A 4 Ω4\ \Omega resistor and an unknown resistor RR are connected in series to a battery. A voltmeter reads 2 V2\ \text{V} across the 4 Ω4\ \Omega resistor and 5 V5\ \text{V} across RR.

    (a) Find RR and the battery's potential difference. [2]

    (b) What resistance must be connected in parallel with RR so that the two voltmeter readings become equal? [1]

    Medium
    3 marks
  79. 79

    Question 79

    A 4 Ω4\ \Omega resistor and a resistor RR are connected in parallel across a battery. In any given time the 4 Ω4\ \Omega resistor produces three times as much heat as RR.

    (a) Find RR. [2]

    (b) The two resistors are now connected in series across the same battery. Find the ratio of the heat produced in the 4 Ω4\ \Omega resistor to that in RR. [1]

    Hard
    3 marks
  80. 80

    Question 80

    Read the following and answer all the sub-questions.

    The circuit diagram shows a laboratory circuit set up to study how the current through a resistance coil varies with the potential difference across it. A battery, a key, a rheostat and the coil are joined in one loop, and two meters are connected — M1\mathrm{M_1} in the loop itself, and M2\mathrm{M_2} across the coil.

    circuit with meter M1 in the loop and meter M2 across the coil

    (a) Name meter M1\mathrm{M_1} and meter M2\mathrm{M_2}, and state what each one measures. [1]

    (b) An ammeter is built to have a very low resistance and a voltmeter a very high resistance. Explain the reason for each. [2]

    (c) A student accidentally connects the ammeter across the coil instead of in the loop. Describe what happens, and explain why this is dangerous for the instrument. [2]

    Hard
    5 marks