Confirming your payment

Skip to content

Opening your dashboard

Class 12 Physics Chapter 12 Semiconductor Electronics, Devices And Circuits: Competency-Based Questions (CBQ)

80 questions on Chapter 12, each worked through on its own page with the AI tutor. Class 12 Physics, CBSE 2026-27.

80 questions

1–5 marks · Mixed difficulty

  1. 1

    Question 1

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): At room temperature Ge has more thermally generated electron-hole pairs than Si.

    Reason (R): A Ge atom is heavier than a Si atom.

    MCQMedium
    1 mark
  2. 2

    Question 2

    A silicon crystal is doped with arsenic to a donor concentration ND=1×1021 m−3N_D = 1\times10^{21}\ \text{m}^{-3}. At room temperature all the donors are ionised. Consider these statements:

    I. The free-electron concentration is close to 1×1021 m−31\times10^{21}\ \text{m}^{-3}.

    II. The crystal carries a net negative charge, because it has far more free electrons than holes.

    III. The positive charge of the ionised donor cores balances the negative charge of the free electrons (together with the few holes), so the crystal is neutral.

    IV. The positive donor ions move through the crystal like holes and carry part of the current.

    Which statements are correct?

    MCQMedium
    1 mark
  3. 3

    Question 3

    A germanium p-n junction has a barrier potential V0=0.35V_0 = 0.35 V. It is first forward biased with 0.20 V and then reverse biased with 1.50 V. What are the effective barrier heights in the two cases?

    MCQMedium
    1 mark
  4. 4

    Question 4

    In the half-wave rectifier shown, the diode has been connected the other way round from the usual circuit: its anode is joined to the load RLR_L and its cathode to the upper end S of the transformer secondary. The output VoutV_{\text{out}} is the potential of the upper end Y of RLR_L relative to its lower end Z. The ac input across the secondary is also shown.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    Which statement correctly describes the output voltage? Take the diode to be ideal.

    MCQMedium
    1 mark
  5. 5

    Question 5

    In the circuit shown, a 12 V battery drives current through R1=4 kΩR_1 = 4\ \text{k}\Omega to the point X. Between X and ground are connected, in parallel, an ideal diode D and a resistor R2=8 kΩR_2 = 8\ \text{k}\Omega. The diode's anode is at X and its cathode is at ground.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    What are the voltage VR2V_{R_2} across R2R_2 and the current II drawn from the battery?

    MCQMedium
    1 mark
  6. 6

    Question 6

    An n-type semiconductor sample at a fixed temperature has an electron concentration ne=1×1022 m−3n_e = 1\times10^{22}\ \text{m}^{-3} and a hole concentration nh=1×1010 m−3n_h = 1\times10^{10}\ \text{m}^{-3}. A second sample of the same material, at the same temperature, has twice the donor concentration, with all donors ionised. What is the hole concentration in the second sample?

    MCQMedium
    1 mark
  7. 7

    Question 7

    A copper wire and a piece of pure (intrinsic) silicon, both at 300 K, are heated to 350 K. Which of the following correctly describes the change in their resistances and the reason?

    MCQMedium
    1 mark
  8. 8

    Question 8

    Silicon is doped with a small amount of boron to make it p-type. Consider these statements about the crystal at room temperature:

    I. The acceptor energy level EAE_A lies slightly above the top of the valence band EVE_V, about 0.01 to 0.05 eV above it.

    II. Most acceptor atoms have taken an electron from the valence band, leaving a hole in the valence band for each of them.

    III. Each ionised acceptor is a fixed negative ion in the lattice.

    IV. Each ionised acceptor also releases a free electron into the conduction band.

    Which statements are correct?

    MCQMedium
    1 mark
  9. 9

    Question 9

    A square-wave voltage that switches between +6 V and −6 V is applied to a resistor RR in series with a silicon diode, as shown. The output VoutV_{\text{out}} is taken across the diode, with the polarity marked. The diode has a forward drop of 0.7 V when conducting and negligible reverse current.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    What values does VoutV_{\text{out}} take?

    MCQMedium
    1 mark
  10. 10

    Question 10

    An ac source is connected across two branches in parallel. Branch 1 has diode D1D_1 in series with bulb B1B_1, and branch 2 has diode D2D_2 in series with bulb B2B_2. The diodes face opposite ways, as shown.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    Which statement about the bulbs is correct?

    MCQMedium
    1 mark
  11. 11

    Question 11

    In the circuit shown, a 15 V supply feeds two voltage dividers. In the first, 3 kΩ runs from the supply to node A and 6 kΩ from A to ground. In the second, 2 kΩ runs from the supply to node B and 2 kΩ from B to ground. An ideal diode D is connected between the two nodes, with its anode at A and its cathode at B.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    (a) Find the potentials of A and B if the diode were removed. Use them to decide whether the diode conducts.

    (b) Find the common potential of A and B with the diode in place, and the current through the diode.

    (c) The diode is turned round. Find the potentials of A and B, and the reverse voltage across the diode.

    Medium
    3 marks
  12. 12

    Question 12

    A silicon p-n junction has a barrier potential V0=0.7V_0 = 0.7 V across a depletion region 0.5 µm wide.

    (a) Estimate the average electric field in the depletion region and state its direction. Why does this direction sweep minority carriers across the junction?

    (b) Under a reverse bias of 5 V the depletion region widens to 1.5 µm. Estimate the new average field.

    Medium
    2 marks
  13. 13

    Question 13

    Read the passage and answer the questions that follow.

    Pure silicon has about 5×10285\times10^{28} atoms per cubic metre. At 300 K its intrinsic carrier concentration is ni=1.5×1016 m−3n_i = 1.5\times10^{16}\ \text{m}^{-3}. A manufacturer dopes a silicon wafer with arsenic at a level of 2 parts per million (2 ppm), so that 2 of every 10610^6 silicon atoms are replaced by arsenic atoms. At 300 K every arsenic atom is ionised. In equilibrium the electron and hole concentrations obey nenh=ni2n_e n_h = n_i^2.

    (a) Find the donor concentration NDN_D. (1 mark)

    (b) Find the hole concentration nhn_h at 300 K. (1 mark)

    (c) Find the ratio of majority carriers to minority carriers. (1 mark)

    (d) Thermal generation also produces free electrons in the doped wafer. Explain why the electron concentration can still be taken equal to NDN_D. (1 mark)

    (e) The temperature of the wafer rises a little above 300 K. State what happens to nen_e and to nhn_h, and why. (1 mark)

    Medium
    5 marks
  14. 14

    Question 14

    A student connects a silicon diode directly across a 3 V cell in forward bias, with no other component in the circuit. The diode conducts appreciably above about 0.7 V.

    (a) What happens to the diode, and why?

    (b) What must be added to the circuit? Explain why, once it is added, the current is fixed mainly by the added component and hardly at all by the diode.

    Medium
    2 marks
  15. 15

    Question 15

    Arsenic is a good dopant for silicon, and it is added only at a level of a few parts per million. Explain the two conditions an impurity atom must meet to be a suitable dopant for silicon, and why only a very small amount is added.

    Medium
    2 marks
  16. 16

    Question 16

    (a) Sketch how the electric potential varies with distance across an unbiased p-n junction, from deep in the p-region to deep in the n-region.

    (b) Which side is at the higher potential, and why? State the direction of the electric field in the depletion region.

    Medium
    2 marks
  17. 17

    Question 17

    A silicon diode is to be forward biased from a 24 V supply through a series resistor RR, as shown. The diode has a forward drop of 0.7 V when conducting and is rated for a maximum forward current of 40 mA.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    (a) Find the smallest value of RR that keeps the current within the rating.

    (b) A germanium diode with the same 40 mA rating but a forward drop of 0.3 V is fitted in place of the silicon diode, with RR unchanged. Find the current, and the smallest RR that would now be safe.

    (c) A standard resistor of 620 Ω is used. Show that it is safe with either diode.

    Medium
    3 marks
  18. 18

    Question 18

    In a piece of intrinsic silicon, electron-hole pairs are constantly being created and destroyed.

    (a) Explain why, at a fixed temperature, the number of free electrons per unit volume stays constant even though pairs are created all the time.

    (b) What happens to this number when the temperature is raised, and why?

    (c) Why is the number of free electrons always equal to the number of holes in an intrinsic semiconductor?

    Medium
    3 marks
  19. 19

    Question 19

    A rectifier for a small appliance is to give a peak output of 12 V from 220 V rms mains. Rectifier circuits are usually fed through a transformer.

    (a) Why is a transformer used, rather than joining the diode directly to the mains?

    (b) Taking the diode as ideal, find the rms voltage the secondary must give and the turns ratio (primary : secondary) of the transformer.

    Medium
    2 marks
  20. 20

    Question 20

    In the early days of radio, signals were detected using a crystal of galena (lead sulphide, PbS) touched by a fine metal wire, the "cat's whisker". The incoming radio signal is an alternating current.

    (a) Which property of the metal-galena point contact made it useful as a detector?

    (b) Explain why a contact that conducted equally well in both directions would give no signal in the earphone.

    Medium
    2 marks
  21. 21

    Question 21

    Carbon, silicon, germanium and tin are all in group IV and all have the same kind of outer electron arrangement. Their energy gaps are 5.4 eV, 1.1 eV, 0.7 eV and 0 eV respectively. Which statement correctly explains why tin behaves as a metal?

    MCQEasy
    1 mark
  22. 22

    Question 22

    A bar of intrinsic silicon is placed in a uniform electric field that points to the right. Consider these statements:

    I. The free electrons move to the left.

    II. The holes move to the right.

    III. The current carried by the electrons points to the right.

    IV. The total current is the sum of the electron current and the hole current, I=Ie+IhI = I_e + I_h.

    Which statements are correct?

    MCQEasy
    1 mark
  23. 23

    Question 23

    A small amount of each of the following elements is added, one at a time, to pure germanium: As, In, Sb, B, P, Al. Which set lists exactly those that make the germanium n-type?

    MCQEasy
    1 mark
  24. 24

    Question 24

    On an energy band diagram of silicon, lines are drawn for ECE_C and EVE_V, and the gap between them is labelled EgE_g. Which one of the following statements is NOT correct?

    MCQEasy
    1 mark
  25. 25

    Question 25

    Consider these statements about six semiconducting materials: anthracene, polypyrrole, GaAs, Ge, CdS and doped phthalocyanine.

    I. Ge is an elemental semiconductor, while GaAs and CdS are inorganic compound semiconductors.

    II. Anthracene and doped phthalocyanine are organic semiconductors, while polypyrrole is an organic polymer semiconductor.

    III. CdS is an organic semiconductor, because sulphur is found in many organic compounds.

    IV. Doped phthalocyanine is an organic polymer semiconductor of the same kind as polypyrrole.

    Which statements are correct?

    MCQEasy
    1 mark
  26. 26

    Question 26

    The graph shows the forward characteristic of a silicon diode. Two points on it are marked: (0.62 V, 2 mA) and (0.68 V, 14 mA).

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    What is the dynamic resistance of the diode between these two points?

    MCQEasy
    1 mark
  27. 27

    Question 27

    A half-wave rectifier with an ideal diode is fed from 220 V rms, 50 Hz mains through a step-down transformer with turns ratio 10 : 1. What are the peak voltage across the load and the frequency of the output pulses?

    MCQEasy
    1 mark
  28. 28

    Question 28

    Three materials have these resistivities at room temperature:

    X: 1.7×10−8 Ω1.7\times10^{-8}\ \Omega m

    Y: 2.3×103 Ω2.3\times10^{3}\ \Omega m

    Z: 1×1014 Ω1\times10^{14}\ \Omega m

    Using the usual ranges of resistivity for metals (10−210^{-2} to 10−8 Ω10^{-8}\ \Omega m), semiconductors (10−510^{-5} to 106 Ω10^{6}\ \Omega m) and insulators (101110^{11} to 1019 Ω10^{19}\ \Omega m), how are X, Y and Z classified?

    MCQEasy
    1 mark
  29. 29

    Question 29

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): Light whose photon energy is greater than EgE_g increases the conductivity of pure silicon.

    Reason (R): Each absorbed photon of energy ≥Eg\geq E_g lifts an electron from the valence band to the conduction band, creating an electron-hole pair.

    MCQEasy
    1 mark
  30. 30

    Question 30

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): In an intrinsic semiconductor the number of holes is greater than the number of free electrons.

    Reason (R): In an intrinsic semiconductor holes are created when electrons are excited from donor levels into the conduction band.

    MCQEasy
    1 mark
  31. 31

    Question 31

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): The depletion region of an unbiased p-n junction contains fixed ions but almost no free charge carriers.

    Reason (R): The ions in the depletion region drift out of it under the junction field.

    MCQEasy
    1 mark
  32. 32

    Question 32

    A full-wave rectifier uses two ideal diodes and a centre-tap transformer whose secondary is rated 15-0-15 V rms. The mains frequency is 50 Hz. The circuit is shown.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    What are the peak voltage across the load RLR_L and the frequency of the output?

    MCQEasy
    1 mark
  33. 33

    Question 33

    Read the passage and answer the questions that follow.

    A student measures the V-I characteristic of a silicon diode. For forward bias she uses a milliammeter and for reverse bias a microammeter. Her readings are:

    Voltage VV (V)0.600.700.750.80−5−15
    Current II1 mA8 mA24 mA64 mA−1.0 µA−1.2 µA

    (a) Sketch the forward characteristic from the readings and estimate the threshold voltage. (1 mark)

    (b) Find the dynamic resistance of the diode between 0.70 V and 0.75 V, and between 0.75 V and 0.80 V. What happens to it as the current increases? (2 marks)

    (c) Find the resistance of the diode at a reverse voltage of 15 V. (1 mark)

    (d) Compare the resistance of the diode at 0.80 V forward with your answer to (c), and use the comparison to explain why this diode can be used as a rectifier. (1 mark)

    Medium
    5 marks
  34. 34

    Question 34

    Read the passage and answer the questions that follow.

    Carbon (as diamond), silicon, germanium and tin all have the same kind of crystal structure, with four valence electrons per atom. Yet their electrical behaviour is very different. The energy gaps between their valence and conduction bands are: C 5.4 eV, Si 1.1 eV, Ge 0.7 eV and Sn 0 eV. The typical thermal energy is kTkT, with k=8.62×10−5k = 8.62\times10^{-5} eV K−1^{-1}, so kT=0.026kT = 0.026 eV at 300 K. The number of electrons that thermal energy can lift across a gap falls extremely rapidly as the ratio Eg/kTE_g/kT grows. A solid with Eg>3E_g > 3 eV is classed as an insulator and one with Eg<3E_g < 3 eV as a semiconductor.

    (a) Calculate Eg/kTE_g/kT at 300 K for C, Si and Ge. (2 marks)

    (b) Classify each of the four elements as an insulator, a semiconductor or a metal, giving your reason. (1 mark)

    (c) A new material has Eg=2.5E_g = 2.5 eV. Find Eg/kTE_g/kT at 300 K and classify it. How does its number of thermally generated carriers compare with that of Si? (1 mark)

    (d) A diamond window is heated to 1000 K. Find Eg/kTE_g/kT for diamond at this temperature, and state whether it will still behave as an insulator. (1 mark)

    Medium
    5 marks
  35. 35

    Question 35

    Gallium arsenide is a compound semiconductor in which Ga and As atoms are normally present in the ratio 1 : 1. A crystal grown with the composition Ga1.1As0.9\text{Ga}_{1.1}\text{As}_{0.9} behaves as an extrinsic semiconductor, even though no foreign atom has been added.

    (a) Explain how the departure from the 1 : 1 ratio can change the type of the semiconductor.

    (b) How does this differ from the way the type of silicon is controlled?

    Easy
    2 marks
  36. 36

    Question 36

    A germanium diode (forward drop 0.3 V) and a silicon diode (forward drop 0.7 V) are connected in series, both forward biased, with a 1.6 kΩ resistor across a 9 V battery, as shown. Take each diode to have negligible resistance once it conducts.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    (a) Find the current in the circuit.

    (b) Find the voltage across each diode and across the resistor.

    (c) The germanium diode is now turned round, the rest of the circuit being unchanged. Find the current and the voltage across the germanium diode.

    Easy
    4 marks
  37. 37

    Question 37

    A 12 V battery powers an electronic device that would be damaged if the battery were ever inserted the wrong way round. To protect it, a silicon diode (forward drop 0.7 V) is placed in series between the battery and the device. In normal use the device draws 200 mA.

    (a) Which way round must the diode be connected? Draw the circuit.

    (b) What happens if the battery is inserted the wrong way round?

    (c) What is the cost of this protection in normal use? Find the voltage reaching the device and the power dissipated in the diode.

    Easy
    3 marks
  38. 38

    Question 38

    Silicon has 5×10285\times10^{28} atoms per m³, and at 300 K its intrinsic carrier concentration is ni=1.5×1016 m−3n_i = 1.5\times10^{16}\ \text{m}^{-3}.

    (a) What fraction of the silicon atoms have lost an electron to the conduction band at 300 K?

    (b) The silicon is doped with 1 ppm of arsenic, all ionised. By roughly what factor does the number of free electrons increase?

    (c) Use these results to explain why a tiny amount of doping changes the conduction of silicon so greatly.

    Easy
    3 marks
  39. 39

    Question 39

    Read the passage and answer the questions that follow.

    A simple dc supply is built as a half-wave rectifier. The 220 V, 50 Hz mains is stepped down by a transformer whose secondary gives 18 V rms. The secondary is connected to a diode in series with a load resistor RLR_L, and the output is taken across RLR_L. Take the diode to be ideal.

    (a) Find the peak voltage across the load. (1 mark)

    (b) State the frequency of the output pulses. (1 mark)

    (c) During the half-cycle in which the diode does not conduct, what is the largest voltage across the diode? Why must the diode's reverse breakdown voltage be more than this? (1 mark)

    (d) Sketch the voltage across the secondary and the voltage across the load against time. (1 mark)

    (e) State in one line what a large capacitor connected across the load would do. (1 mark)

    Easy
    5 marks
  40. 40

    Question 40

    The figure shows part of a silicon lattice. At site 1 a covalent bond has lost an electron, leaving a hole. Site 2 is a neighbouring bond, still complete.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    (a) An electron from the bond at site 2 jumps into the vacancy at site 1. Where is the hole now? What has actually moved?

    (b) Explain why the hole behaves as a particle of charge +e+e.

    (c) A conduction electron wandering through the crystal now falls into the vacancy at site 2. What happens to the hole, and to the number of free carriers in the crystal?

    Easy
    3 marks
  41. 41

    Question 41

    An abrupt silicon p-n junction has acceptor concentration NA=3×1022N_A = 3\times10^{22} m⁻³ on the p-side and donor concentration ND=9×1020N_D = 9\times10^{20} m⁻³ on the n-side, all ionised; ni=1.5×1016n_i = 1.5\times10^{16} m⁻³. Far from the junction on each side, the minority carrier concentrations (electrons on the p-side, holes on the n-side), and the factor by which the hole concentration falls from the p-side to the n-side, are

    MCQMedium
    1 mark
  42. 42

    Question 42

    In silicon, a donor (arsenic) level lies 0.045 eV below the bottom of the conduction band, and the band gap is 1.1 eV. Take k=8.62×10−5k = 8.62\times10^{-5} eV K⁻¹. Consider the statements:

    (i) At 300 K, kT≈0.026kT \approx 0.026 eV, which is comparable to 0.045 eV, so nearly all the donors are ionised.

    (ii) At 30 K, kT≈0.0026kT \approx 0.0026 eV, about one-seventeenth of 0.045 eV, so most donors keep their fifth electron and the sample conducts poorly.

    (iii) Breaking a covalent bond needs the full 1.1 eV gap, more than twenty times the 0.045 eV that frees a donor electron, so in a doped sample at 300 K the conduction electrons come mainly from the donors rather than from broken covalent bonds.

    (iv) Cooling the sample from 300 K to 30 K increases the number of free electrons, because the lattice vibrates less.

    Which statements are correct?

    MCQMedium
    1 mark
  43. 43

    Question 43

    In germanium, consider three transitions: E1E_1, the energy to lift an electron from a donor level into the conduction band; E2E_2, the energy to lift an electron from the valence band into an acceptor level; and E3E_3, the energy to lift an electron from the valence band into the conduction band. Which statement about their sizes, and about the free carriers each transition creates, is correct?

    MCQMedium
    1 mark
  44. 44

    Question 44

    A germanium crystal contains 1×10221\times10^{22} atoms. The outer shell of each atom offers 8 states (in its s and p sub-shells) and holds 4 valence electrons. As the atoms come together to form the crystal, these states spread into a valence band and a conduction band, as described in NCERT for Si and Ge. Consider:

    (i) The crystal has 4×10224\times10^{22} valence electrons.

    (ii) There are 8×10228\times10^{22} states in all, shared equally between the valence band and the conduction band.

    (iii) At 0 K the valence band is completely filled and the conduction band is completely empty.

    (iv) The conduction band has 8×10228\times10^{22} states, since every electron needs two states to move between.

    Which statements are correct?

    MCQMedium
    1 mark
  45. 45

    Question 45

    A p-n junction diode carries a steady forward current II. Consider:

    (i) Deep inside the p-side, far from the junction, the current is carried almost entirely by holes.

    (ii) Deep inside the n-side, far from the junction, the current is carried almost entirely by electrons.

    (iii) Just beyond the junction on the n-side, part of the current is carried by holes injected from the p-side, and these holes recombine with electrons as they move further in.

    (iv) The total current is larger at the junction than deep inside either side, because both kinds of carrier cross the junction there.

    Which statements are correct?

    MCQMedium
    1 mark
  46. 46

    Question 46

    Infrared light of wavelength 1.5 µm falls on a slab of pure germanium (Eg=0.7E_g = 0.7 eV) and on a slab of pure silicon (Eg=1.1E_g = 1.1 eV). (hc=1240hc = 1240 eV nm.) Which statement is correct?

    MCQHard
    1 mark
  47. 47

    Question 47

    A silicon crystal and a germanium crystal are each doped with donors to ND=4×1021N_D = 4\times10^{21} m⁻³, all ionised, at 300 K. At this temperature ni=1.5×1016n_i = 1.5\times10^{16} m⁻³ for Si and ni=2.4×1019n_i = 2.4\times10^{19} m⁻³ for Ge. The hole concentrations in the Si and the Ge crystal, and how they compare, are

    MCQMedium
    1 mark
  48. 48

    Question 48

    Four silicon diodes (threshold voltage 0.7 V) are parts of larger circuits. The figure shows, for each diode, the potentials the rest of its circuit would put on its anode (p-side) and cathode (n-side) if the diode drew no current.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    Which of the diodes will conduct an appreciable current?

    MCQMedium
    1 mark
  49. 49

    Question 49

    The graph shows part of the forward characteristic of a silicon diode, with two points marked.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    Consider:

    (i) The dynamic resistance between the two marked points is 3.0 Ω.

    (ii) The static (dc) resistance V/IV/I at 0.76 V is about 30.4 Ω.

    (iii) The static resistance at 0.70 V is 140 Ω, larger than at 0.76 V.

    (iv) Since the dynamic resistance is only 3.0 Ω, a steady 0.76 V applied directly across the diode drives about 0.25 A through it.

    Which statements are correct?

    MCQHard
    1 mark
  50. 50

    Question 50

    In the circuit shown, the cell has emf 2.7 V and negligible internal resistance. The silicon diode is modelled as a constant 0.7 V drop in series with its dynamic resistance rd=5r_d = 5 Ω, once it conducts.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    The current in the circuit and the voltage across the diode are

    MCQMedium
    1 mark
  51. 51

    Question 51

    An n-type silicon sample has donor concentration ND=1×1021N_D = 1\times10^{21} m⁻³, all ionised at every temperature considered. The intrinsic carrier concentration of Si rises steeply with temperature: ni=1.5×1016n_i = 1.5\times10^{16} m⁻³ at 300 K, 1×10201\times10^{20} m⁻³ at 600 K and 5×10215\times10^{21} m⁻³ at 800 K.

    (a) Find the electron and hole concentrations at 300 K.

    (b) Find the electron and hole concentrations at 600 K. Is the sample still clearly n-type?

    (c) Find the electron and hole concentrations at 800 K, and describe how the sample now behaves.

    Medium
    3 marks
  52. 52

    Question 52

    In any semiconductor in thermal equilibrium, nenh=ni2n_e n_h = n_i^2.

    (a) Show that the total carrier concentration ne+nhn_e + n_h can never be less than 2ni2n_i, and that it equals 2ni2n_i only when ne=nhn_e = n_h.

    (b) A silicon sample (ni=1.5×1016n_i = 1.5\times10^{16} m⁻³) is lightly doped with donors so that ne=3×1016n_e = 3\times10^{16} m⁻³. Find nhn_h and ne+nhn_e + n_h, and compare the total with that of pure silicon.

    (c) A student claims: "Adding a small amount of acceptor impurity to pure silicon can reduce the total number of carriers, because the holes it adds recombine with the free electrons." Use (a) to decide whether the claim is right.

    Medium
    3 marks
  53. 53

    Question 53

    The graph shows the forward characteristics of two diodes, P and Q. One is made of germanium and the other of silicon. Two points are marked on each curve.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    (a) Which curve belongs to the germanium diode? Give a reason based on the graph.

    (b) Find the dynamic resistance of diode P between its two marked points.

    (c) Find the dynamic resistance of diode Q between its two marked points.

    (d) An ac signal of peak 0.4 V is applied to each diode in turn, in series with a load resistor. Which diode gives an output across the load? Explain.

    Medium
    4 marks
  54. 54

    Question 54

    In the battery-backup circuit shown, a 9 V adapter feeds node Y through silicon diode D₁, and a 6 V backup cell feeds Y through silicon diode D₂. The load is a 2 kΩ resistor from Y to the common line. Each diode conducts with a 0.7 V drop when forward biased. Both sources have negligible internal resistance.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    (a) With the adapter on, find the potential of Y and the load current. Show that the backup cell supplies nothing.

    (b) The adapter is switched off (its output falls to 0 V). Find the new potential of Y and the load current.

    Medium
    2 marks
  55. 55

    Question 55

    (a) In a crystal, the electrons of the valence band are not tied to particular atoms; they belong to the crystal as a whole. Explain why a completely filled valence band still cannot carry any current when an electric field is applied.

    (b) Explain how exciting a few electrons into the conduction band makes both bands able to carry current.

    Medium
    2 marks
  56. 56

    Question 56

    In the circuit shown, the input is applied through a 1 kΩ resistor, and two silicon diodes (drop 0.7 V each when conducting) are connected in series from the output terminal to the common wire.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    (a) Find voutv_{out} and the current in the 1 kΩ resistor when vin=+10v_{in} = +10 V (steady).

    (b) Find voutv_{out} and the current when vin=+0.9v_{in} = +0.9 V.

    (c) Find voutv_{out} when vin=−5v_{in} = -5 V. Hence describe what this circuit does to an input voltage.

    Medium
    3 marks
  57. 57

    Question 57

    A diode has a reverse current of about 1 µA at any reverse voltage up to its breakdown voltage of 50 V. It is rated to carry at most 10 mA.

    (a) Find the power developed in the diode when it is reverse biased at 40 V.

    (b) The diode is now connected in reverse across a 60 V supply through a 500 Ω resistor. It breaks down and keeps about 50 V across itself. Find the reverse current and the power developed in the diode, and explain why the diode is destroyed although it survived (a).

    Medium
    2 marks
  58. 58

    Question 58

    In a forward-biased p-n junction, holes cross from the p-side into the n-side, where they are minority carriers.

    (a) A student argues: "Holes keep diffusing into the n-side, so the hole concentration there will soon equal that on the p-side, and the diffusion current will stop." Explain why this does not happen.

    (b) Sketch how the hole concentration varies with distance into the n-side under forward bias, and compare it with the unbiased junction.

    (c) If the forward bias is increased, how do the hole concentration at the junction edge (on the n-side) and the current change? Explain using the barrier height V0−VV_0 - V.

    Medium
    3 marks
  59. 59

    Question 59

    A full-wave rectifier with two ideal diodes is built on a transformer whose centre tap was wound in the wrong place by mistake: the upper half of the secondary gives 9 V (rms) and the lower half 7 V (rms). The mains frequency is 50 Hz.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    (a) Find the peak voltages of the pulses across the load.

    (b) How many pulses reach the load each second? After how long does the output pattern repeat, and what is the frequency of that repetition? Which diode gives the taller pulses?

    Medium
    2 marks
  60. 60

    Question 60

    A full-wave rectifier with a centre-tapped transformer works from 50 Hz mains. One of its diodes, D₂, burns out and becomes an open circuit.

    (a) Sketch the output across the load before and after the fault, and state the output frequency in each case.

    (b) Does the peak output voltage change? Does the largest reverse voltage across the healthy diode D₁ change? Explain, taking the peak voltage of each half of the secondary as VmV_m and the diodes as ideal.

    Medium
    2 marks
  61. 61

    Question 61

    A sinusoidal voltage of peak value 1.0 V is applied to a silicon diode in series with a load RLR_L, as shown. Take the diode to conduct, with a constant drop of 0.7 V, only while the input exceeds 0.7 V.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    The peak voltage across RLR_L, and the fraction of each cycle during which current flows in RLR_L, are

    MCQMedium
    1 mark
  62. 62

    Question 62

    In the circuit shown, D is an ideal diode, and both cells have negligible internal resistance.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    The potential of node N (relative to the bottom wire) and the current through the diode are

    MCQMedium
    1 mark
  63. 63

    Question 63

    A germanium diode (drop 0.3 V) and a silicon diode (drop 0.7 V) are connected in parallel, both forward biased, and fed from a 5 V cell of negligible internal resistance through 1 kΩ, as shown.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    The currents in the Si diode and in the Ge diode are respectively

    MCQMedium
    1 mark
  64. 64

    Question 64

    The output of a rectifier working from 50 Hz mains is smoothed by a filter. Consider:

    (i) With a capacitor CC across the load, a half-wave rectifier recharges it once every 20 ms, and a full-wave rectifier once every 10 ms.

    (ii) Between recharges the capacitor discharges through the load RLR_L, and the voltage falls only a little if CRLCR_L is much larger than the time between recharges.

    (iii) An inductor in series with the load also smooths the output, because it opposes changes in the current.

    (iv) With a large CC, the diode conducts throughout each positive half-cycle.

    Which statements are correct?

    MCQMedium
    1 mark
  65. 65

    Question 65

    A half-wave rectifier uses a silicon diode (drop 0.7 V when conducting) and a resistive load. Its input is a sinusoidal voltage of peak 5 V at 50 Hz. Consider:

    (i) The peak voltage across the load is 4.3 V.

    (ii) Pulses appear across the load 50 times per second.

    (iii) During each negative half-cycle the diode must withstand a reverse voltage of up to 5 V.

    (iv) The largest reverse voltage across the diode is 5.7 V, since the 0.7 V drop adds to the input peak.

    Which statements are correct?

    MCQMedium
    1 mark
  66. 66

    Question 66

    A half-wave rectifier is connected directly to the 230 V (rms), 50 Hz mains, with no transformer. A large capacitor is connected across its load, so the output stays close to the peak mains voltage. The largest reverse voltage across the diode, and the reason, are

    MCQMedium
    1 mark
  67. 67

    Question 67

    In the loop shown, D is a silicon diode that conducts with a 0.7 V drop, and both cells have negligible internal resistance.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    The current in the 4 Ω resistor as drawn, and after the 2 V cell is turned round, are

    MCQMedium
    1 mark
  68. 68

    Question 68

    A square wave that switches between +10 V and −10 V is applied to the circuit shown. A silicon diode (drop 0.7 V) and a germanium diode (drop 0.3 V) are connected in anti-parallel, followed by 1 kΩ and 2 kΩ resistors in series.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    The output voltage across the 2 kΩ resistor switches between

    MCQHard
    1 mark
  69. 69

    Question 69

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): The reverse current of a p-n junction diode, below breakdown, increases markedly when the diode is heated.

    Reason (R): The reverse current is carried by minority carriers, and their number is set by the thermal generation of electron-hole pairs.

    MCQMedium
    1 mark
  70. 70

    Question 70

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): An n-type semiconductor has more free electrons than holes.

    Reason (R): A hole carries an effective charge of +e+e.

    MCQHard
    1 mark
  71. 71

    Question 71

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): In forward bias, the current in a silicon diode is negligible until the applied voltage reaches about 0.7 V.

    Reason (R): Below 0.7 V of forward bias, the depletion region contains no ions.

    MCQMedium
    1 mark
  72. 72

    Question 72

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): A capacitor connected across the load of a rectifier makes the output voltage exactly equal to the rms value of the ac input.

    Reason (R): A capacitor passes dc and blocks ac.

    MCQHard
    1 mark
  73. 73

    Question 73

    Read the passage and answer the questions that follow.

    A student builds the network below to test how silicon diodes share current between branches. Each Si diode is taken to conduct with a constant drop of 0.7 V when forward biased and to carry no current otherwise. The cell has emf 12 V and negligible internal resistance.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    (a) Find the potential of node A relative to the common (bottom) wire. (2 marks)

    (b) Find the currents in the 1 kΩ, 3.3 kΩ and 2 kΩ resistors. (1 mark)

    (c) D₂ is now reversed. Find the new potential of A and the current drawn from the cell. (1 mark)

    (d) D₂ is restored and D₁ is reversed instead. Find the currents in the network, with a reason. (1 mark)

    Hard
    5 marks
  74. 74

    Question 74

    Read the passage and answer the questions that follow.

    Light can create an electron-hole pair in a solid only if a single photon carries at least the band-gap energy EgE_g, enough to lift an electron from the valence band into the conduction band. Four materials have band gaps of 5.4 eV (diamond), 1.43 eV (GaAs), 1.74 eV (CdSe) and 2.42 eV (CdS). Visible light spans wavelengths from about 400 nm to 700 nm. (hc=1240hc = 1240 eV nm.)

    (a) Find the longest wavelength of light that can create electron-hole pairs in each of the four materials. (2 marks)

    (b) Which of the four materials gain pairs when red light of wavelength 650 nm falls on them? Show the comparison. (1 mark)

    (c) Which material is transparent to all visible light, and which passes only part of the visible range? State that part. (1 mark)

    (d) A very intense beam of 1000 nm infrared light falls on GaAs and creates no pairs, while a weak beam of 650 nm light does. Explain. (1 mark)

    Hard
    5 marks
  75. 75

    Question 75

    Read the passage and answer the questions that follow.

    A wafer of pure silicon (ni=1.5×1016n_i = 1.5\times10^{16} m⁻³ at 300 K) is first doped with arsenic to a donor concentration ND=5×1020N_D = 5\times10^{20} m⁻³. Later, one region of the same wafer is also doped with boron to an acceptor concentration NA=2×1021N_A = 2\times10^{21} m⁻³. All the impurity atoms are ionised at 300 K. Where both impurities are present, the electrons given by the donors fill vacant bonds of the acceptors, so the two impurities partly cancel.

    (a) Find the electron and hole concentrations in the wafer after the arsenic doping alone. (1 mark)

    (b) In the region doped with both, state the type of semiconductor and find the hole concentration. (1 mark)

    (c) Find the electron concentration in that region. (1 mark)

    (d) Show that the doubly doped region is electrically neutral. (1 mark)

    (e) Another wafer is doped with boron alone to NA=2×1021N_A = 2\times10^{21} m⁻³. Compare its hole concentration with that of the doubly doped region, and explain the difference. (1 mark)

    Hard
    5 marks
  76. 76

    Question 76

    In the circuit shown, each box D₁ and D₂ contains an ideal diode, but a student has connected them without noting which way round. The cell has emf 12 V and negligible internal resistance, and the ammeter has negligible resistance. The ammeter reads 4.0 A.

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    (a) Find the ammeter reading for each of the four possible ways of connecting the two diodes, and hence state how each diode must be connected.

    (b) For the arrangement in (a), find the current in each branch.

    (c) With the diodes as in (a), the cell is reversed. What does the ammeter read? Explain.

    Hard
    3 marks
  77. 77

    Question 77

    A half-wave rectifier works from 50 Hz mains and feeds a load RL=1R_L = 1 kΩ. A capacitor CC is connected across the load.

    (a) Find the time constant CRLCR_L for C=100C = 100 µF and for C=1C = 1 µF, and compare each with the time between successive charging pulses.

    (b) Sketch the output voltage in the two cases and explain the difference.

    (c) A designer wants CRLCR_L to be at least ten times the time between charging pulses. Find the smallest CC that meets this with RL=1R_L = 1 kΩ, and again if the load is changed to RL=250R_L = 250 Ω.

    Medium
    3 marks
  78. 78

    Question 78

    In a certain p-n junction diode, the drift current across the junction (minority carriers swept across by the junction field) is 5 µA, and it stays practically at this value whatever the bias, below breakdown. The net current through the diode, in the forward direction, equals the diffusion current minus the drift current.

    (a) Find the diffusion current when the diode is unbiased.

    (b) Find the diffusion current when the diode is forward biased and carries 2 mA.

    (c) Find the diffusion current when the diode is reverse biased and the net reverse current is 5 µA. Explain why the diffusion current changes enormously with bias while the drift current does not.

    Medium
    3 marks
  79. 79

    Question 79

    A silicon diode has a forward drop of 0.7 V when conducting, and a reverse current of about 1 µA at a reverse voltage of 20 V.

    (a) The diode is connected in series with a 5 kΩ resistor across a 20 V dc supply, first in forward bias and then in reverse bias. Find the current in each case and the ratio of the two currents.

    (b) The 5 kΩ resistor is replaced by a 5 MΩ resistor. Treating the reverse-biased diode as a resistance of 2×1072\times10^7 Ω, find the forward and reverse currents and their ratio.

    (c) Use your results to explain why the load of a rectifier must be much smaller than the diode's reverse resistance.

    Hard
    3 marks
  80. 80

    Question 80

    Read the passage and answer the questions that follow.

    A full-wave rectifier is built from a transformer with a centre-tapped secondary, two silicon diodes D₁ and D₂ (drop 0.7 V each when conducting) and a load RL=1R_L = 1 kΩ connected between the joined cathodes (X) and the centre tap. The primary is connected to the 220 V (rms), 50 Hz mains, and each half of the secondary gives 11 V (rms).

    Class 12 Physics Semiconductor Electronics, Devices And Circuits

    (a) Find the ratio of the number of turns in the primary to that in the whole secondary. (1 mark)

    (b) Find the peak voltage across the load and the peak current in it. (1 mark)

    (c) What is the frequency of the output? Which diode conducts while the upper end of the secondary is positive relative to the centre tap? (1 mark)

    (d) At the instant D₁ conducts at its peak, find the reverse voltage across D₂. Hence state the least reverse breakdown voltage the diodes must have. (1 mark)

    (e) The load is changed to 500 Ω. Which of your answers to (b), (c) and (d) change, and to what? (1 mark)

    Medium
    5 marks