Confirming your payment

Skip to content

Opening your dashboard

Class 11 Physics Chapter 9 Mechanical Properties Of Fluids: Competency-Based Questions (CBQ)

80 questions on Chapter 9, each worked through on its own page with the AI tutor. Class 11 Physics, CBSE 2026-27.

80 questions

1–5 marks · Mixed difficulty

  1. 1

    Question 1

    A storage tank in a workshop contains 1.0 m of water. A careless worker pours in waste oil of density 800 kg m−3800\ \text{kg m}^{-3}, which does not mix with the water and forms a layer 0.50 m thick on top of it, as shown in the figure. The tank is open to the atmosphere. Taking g=9.8 m s−2g = 9.8\ \text{m s}^{-2} and the density of water 1000 kg m−31000\ \text{kg m}^{-3}, what is the gauge pressure at the bottom of the tank?

    Class 11 Physics Mechanical Properties Of Fluids

    MCQMedium
    1 mark
  2. 2

    Question 2

    A kitchen table has a flat wooden top of area 1.5 m21.5\ \text{m}^2. Atmospheric pressure is 1.013×105 Pa1.013 \times 10^5\ \text{Pa}, so the air above the table pushes down on its top surface with a force of about 1.52×105 N1.52 \times 10^5\ \text{N}, roughly the weight of a 15-tonne lorry. Yet the thin table top does not break or even bend noticeably. Which statement best explains this?

    MCQMedium
    1 mark
  3. 3

    Question 3

    A patient in hospital is given saline through an intravenous (IV) drip. The fluid flows from a bag down a tube into a vein in the arm, where the gauge pressure of the blood is 18 mm Hg. For the fluid to enter the vein, the pressure of the fluid at the needle must be at least this large. The saline has density 1000 kg m−31000\ \text{kg m}^{-3} and the density of mercury is 13.6×103 kg m−313.6 \times 10^3\ \text{kg m}^{-3}. Ignoring flow losses, what is the least height of the fluid surface in the bag above the needle?

    MCQMedium
    1 mark
  4. 4

    Question 4

    A building is supplied with water from a tank on its roof. The water surface in the tank is 15 m above the ground. On a floor 3.0 m above the ground, a tap is closed, and the water presses on the tap's rubber washer over an area of 1.0 cm21.0\ \text{cm}^2. The water in the pipes is at rest. Taking g=9.8 m s−2g = 9.8\ \text{m s}^{-2} and the density of water as 1000 kg m−31000\ \text{kg m}^{-3}, what net force does the water exert on the washer, over and above the force of the atmosphere on its other side?

    MCQMedium
    1 mark
  5. 5

    Question 5

    Water flows through a garden hose of inner diameter 2.0 cm at 0.50 m s−10.50\ \text{m s}^{-1}. A boy fits a nozzle of inner diameter 0.50 cm to the end, and the water now shoots out at high speed. He uses the hose to fill a 10 litre bucket and believes the fast jet will fill it much sooner. Assuming the flow in the hose stays at 0.50 m s−10.50\ \text{m s}^{-1}, how long does the bucket take to fill with the nozzle fitted?

    MCQMedium
    1 mark
  6. 6

    Question 6

    Blood leaves the heart through the aorta, of radius 1.0 cm, at an average speed of 0.30 m s−10.30\ \text{m s}^{-1}. It eventually passes through a huge number of capillaries, each of radius 4.0 μm4.0\ \mu\text{m}, in which it moves at only about 0.50 mm s−10.50\ \text{mm s}^{-1}. Treating blood as incompressible and the flow as steady, about how many capillaries are carrying blood at any time?

    MCQMedium
    1 mark
  7. 7

    Question 7

    In a horizontal water main the pressure is 3.0×105 Pa3.0 \times 10^5\ \text{Pa} and the water flows at 2.0 m s−12.0\ \text{m s}^{-1}. The main is joined, at the same height, to a pipe of half its diameter. Treating water as an ideal fluid of density 1000 kg m−31000\ \text{kg m}^{-3} in steady flow, what are the speed and the pressure of the water in the narrower pipe?

    MCQMedium
    1 mark
  8. 8

    Question 8

    A narrow vertical plastic bottle, open at the top, is filled with water. A hole is made in its base, and the area of the hole is half the cross-sectional area of the bottle. At the moment when the water surface is 1.0 m above the hole, the surface itself is moving down noticeably. Treating water as an ideal fluid and taking g=9.8 m s−2g = 9.8\ \text{m s}^{-2}, with what speed does the water leave the hole at that moment?

    MCQMedium
    1 mark
  9. 9

    Question 9

    A large open water tank on a farm has a leak: a small hole of area 2.0 cm22.0\ \text{cm}^2 in its side, 1.25 m below the water surface. Taking g=9.8 m s−2g = 9.8\ \text{m s}^{-2} and treating water as an ideal fluid, about how much water is lost per minute while the level is still near this height?

    MCQMedium
    1 mark
  10. 10

    Question 10

    Two light table-tennis balls hang side by side from threads, about 3 cm apart. A student blows a steady stream of air horizontally through a straw into the gap between them, so that the stream passes between the balls without hitting either of them. What happens to the balls?

    MCQMedium
    1 mark
  11. 11

    Question 11

    A table-tennis player hits the ball with backspin. The ball moves to the right, and it spins so that its bottom surface moves forward (to the right) and its top surface moves backward relative to the centre of the ball, as shown in the figure. Compared with a ball hit at the same speed without spin, how does the air affect this ball?

    Class 11 Physics Mechanical Properties Of Fluids

    MCQMedium
    1 mark
  12. 12

    Question 12

    In a lab demonstration, glycerine (viscosity 0.83 Pa s0.83\ \text{Pa s}) fills the 2.5 mm gap between a fixed glass plate and a parallel glass plate above it. A straight vertical line of dye is drawn across the glycerine from one plate to the other. The top plate is then pulled sideways at a steady speed, and the dye line tilts: in 2.0 s its top end moves 4.0 cm while its bottom end stays where it was. The flow is laminar. What shearing stress is needed to keep the top plate moving?

    MCQMedium
    1 mark
  13. 13

    Question 13

    Two raindrops, of radii rr and 2r2r, are falling through still air, each at its own terminal velocity. Treat both as spheres obeying Stokes' law. What is the ratio of the viscous drag force on the smaller drop to that on the larger drop?

    MCQMedium
    1 mark
  14. 14

    Question 14

    A morning mist is made of tiny water droplets of radius 10 μm10\ \mu\text{m} settling slowly through still air. Taking the viscosity of air as 1.8×10−5 Pa s1.8 \times 10^{-5}\ \text{Pa s}, the density of water 1000 kg m−31000\ \text{kg m}^{-3}, g=9.8 m s−2g = 9.8\ \text{m s}^{-2}, and neglecting the density of air (and so its upthrust), what are the terminal velocity of a droplet and the viscous drag on it while it falls at that velocity?

    MCQMedium
    1 mark
  15. 15

    Question 15

    A child blows a soap bubble and enlarges it slowly, at constant temperature, from a radius of 1.0 cm to a radius of 2.0 cm. The surface tension of the soap solution is 0.025 N m−10.025\ \text{N m}^{-1}. How much work is done against surface tension?

    MCQMedium
    1 mark
  16. 16

    Question 16

    A student hangs a thin wire ring of radius 2.0 cm horizontally from a sensitive balance, lowers it until it touches clean water, and then slowly raises it. Just before the ring breaks free, a thin film of water clings to it all round. Taking the surface tension of water as 0.0727 N m−10.0727\ \text{N m}^{-1} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}, how much extra downward force does the water exert on the ring at that moment, and what extra mass does the balance show?

    MCQMedium
    1 mark
  17. 17

    Question 17

    A laboratory technician dips the same clean glass capillary tube first into water and then, after drying it, into ethyl alcohol. For both liquids the angle of contact with clean glass is close to zero. Using S=0.0727 N m−1S = 0.0727\ \text{N m}^{-1} and ρ=1000 kg m−3\rho = 1000\ \text{kg m}^{-3} for water, and S=0.0227 N m−1S = 0.0227\ \text{N m}^{-1} and ρ=806 kg m−3\rho = 806\ \text{kg m}^{-3} for ethyl alcohol (Tables 9.1 and 9.3), what is the ratio of the height to which water rises to the height to which ethyl alcohol rises?

    MCQMedium
    1 mark
  18. 18

    Question 18

    A glass tube of internal diameter 2.0 mm is dipped vertically into a dish of mercury. The surface tension of mercury is 0.4355 N m−10.4355\ \text{N m}^{-1}, its angle of contact with glass is 140∘140^\circ and its density is 13.6×103 kg m−313.6 \times 10^3\ \text{kg m}^{-3}. Taking g=9.8 m s−2g = 9.8\ \text{m s}^{-2}, what happens to the level of mercury inside the tube?

    MCQMedium
    1 mark
  19. 19

    Question 19

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): The air pressure inside a small air bubble just below the surface of water is greater than the pressure of the water just outside it.

    Reason (R): For a curved liquid surface, the pressure on the concave side is greater than on the convex side.

    MCQMedium
    1 mark
  20. 20

    Question 20

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): Water rises higher in a narrower glass capillary than in a wider one.

    Reason (R): The upward force of surface tension on the water column is the same in a narrow tube as in a wide one.

    MCQMedium
    1 mark
  21. 21

    Question 21

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): In steady flow, two streamlines never cross each other.

    Reason (R): In steady flow, the speed of a fluid particle stays the same all along its streamline.

    MCQMedium
    1 mark
  22. 22

    Question 22

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): When a liquid in a closed container is squeezed by a piston, the pressure increases by the same amount at the bottom of the container as at the top.

    Reason (R): In a liquid at rest, the pressure at the bottom of the container is greater than the pressure at the top.

    MCQMedium
    1 mark
  23. 23

    Question 23

    In a garage, a car of mass 1500 kg stands on the large piston of a hydraulic lift. The large piston has a radius of 12 cm and the small piston a radius of 2.0 cm. The small piston is pushed down by a hand lever that multiplies the hand's force by 5, and each stroke moves the small piston down by 10 cm (valves stop the oil from flowing back between strokes). Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}, treat the oil as incompressible, and neglect the masses of the pistons and friction.

    Class 11 Physics Mechanical Properties Of Fluids

    (a) Find the force that must be applied to the small piston to hold the car up, and the pressure of the oil.

    (b) What force must the mechanic apply to the end of the lever?

    (c) How far must the small piston travel in total to raise the car by 0.20 m, and how many strokes does this take?

    (d) Compare the work done on the small piston with the gain in potential energy of the car, and comment.

    Medium
    5 marks
  24. 24

    Question 24

    A vacuum pump is removing air from a sealed glass chamber. The chamber is connected to an open-tube mercury manometer, and the mercury in the open arm now stands 18.0 cm lower than the mercury in the arm joined to the chamber, as shown in the figure. A barometer in the lab reads 75.0 cm of mercury. Take the density of mercury as 13.6×103 kg m−313.6 \times 10^3\ \text{kg m}^{-3} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    Class 11 Physics Mechanical Properties Of Fluids

    (a) Find the absolute pressure in the chamber, in cm of mercury and in pascal.

    (b) Find the gauge pressure in the chamber. What does a negative gauge pressure mean?

    (c) The pump runs on and the pressure in the chamber falls by a further 6.0 cm of mercury. The two arms of the manometer have equal bores. By how much does the mercury level move in each arm, and in which direction? Find the new absolute and gauge pressures in pascal.

    (d) The pump is then switched off and a valve is opened that lets room air back into the chamber. What happens to the mercury levels, and why?

    Medium
    5 marks
  25. 25

    Question 25

    A large open water tank stands on a tower in a village. The water surface is 5.0 m above the level ground and the bottom of the tank is 1.0 m above the ground. A small hole develops in the side of the tank, 1.8 m below the water surface, and a horizontal jet of water comes out. Treat the water as an ideal fluid, neglect air resistance and take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}. The level in the tank falls so slowly that it may be taken as constant.

    Class 11 Physics Mechanical Properties Of Fluids

    (a) With what speed does the water leave the hole?

    (b) How far from the side of the tank does the jet hit the ground?

    (c) Show that a second hole, 3.2 m below the water surface, would send its jet to the same point on the ground.

    (d) At what angle below the horizontal does each jet (from the hole 1.8 m deep and from the hole 3.2 m deep) strike the ground? Explain how the two angles are related.

    Medium
    5 marks
  26. 26

    Question 26

    To measure the viscosity of an engine oil, a student drops a steel ball of radius 1.5 mm into a tall glass cylinder filled with the oil. Two rubber bands are placed round the cylinder 20 cm apart, the upper one well below the surface. The ball takes 4.0 s to fall from the upper band to the lower band, moving at a steady speed. The density of steel is 7.8×103 kg m−37.8 \times 10^3\ \text{kg m}^{-3}, the density of the oil is 950 kg m−3950\ \text{kg m}^{-3} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    Class 11 Physics Mechanical Properties Of Fluids

    (a) Find the terminal velocity of the ball and the viscosity of the oil.

    (b) Calculate the viscous drag on the ball at this speed, and check that it equals the weight of the ball minus the upthrust on it.

    (c) An aluminium ball (density 2.7×103 kg m−32.7 \times 10^3\ \text{kg m}^{-3}) of the same radius is dropped into the same oil. How long does it take to fall between the two bands at its terminal velocity?

    (d) Why is the upper band placed well below the surface of the oil, rather than at the surface?

    Medium
    5 marks
  27. 27

    Question 27

    A model wing of area 0.12 m20.12\ \text{m}^2 is tested in a wind tunnel. Small holes (pressure taps) in its upper and lower surfaces are connected by tubes to the two arms of a U-tube containing water, as shown in the figure. With the air flowing, the water levels in the two arms differ by 2.0 cm. The air flows past the lower surface at 30 m s−130\ \text{m s}^{-1} relative to the wing. Take the density of air 1.2 kg m−31.2\ \text{kg m}^{-3}, the density of water 1000 kg m−31000\ \text{kg m}^{-3} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}. Treat the air as an ideal fluid and assume the pressure difference is the same over the whole wing.

    Class 11 Physics Mechanical Properties Of Fluids

    (a) Find the pressure difference between the lower and upper surfaces, and the lift on the model wing.

    (b) Find the speed of the air over the upper surface.

    (c) By what percentage is the air over the wing faster than the air under it? What is it about the wing that produces this difference?

    Medium
    4 marks
  28. 28

    Question 28

    A teacher fills three glass vessels of very different shapes (one widening upwards, one straight-sided, one narrowing upwards) with water to the same depth of 20 cm. Each vessel has a flat base of area 50 cm250\ \text{cm}^2, as shown in the figure. The vessels hold very different amounts of water. Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    Class 11 Physics Mechanical Properties Of Fluids

    (a) Find the gauge pressure of the water on the base of each vessel.

    (b) Find the force exerted by the water on each base.

    (c) The widening vessel holds much more than the 9.8 N of water. Where does the rest of the weight of its water act?

    Medium
    3 marks
  29. 29

    Question 29

    A river 20 m wide and 2.0 m deep flows at an average speed of 1.5 m s−11.5\ \text{m s}^{-1}. Downstream it passes through a rocky gorge where it is only 8.0 m wide but 3.0 m deep. Treat the water as incompressible and the flow as steady.

    (a) Find the average speed of the water in the gorge.

    (b) How many cubic metres of water pass through the gorge in one hour?

    (c) Rafters notice the water in the gorge is fast and choppy. Is the narrower gorge necessarily where the water is fastest? Explain using the equation of continuity.

    Medium
    3 marks
  30. 30

    Question 30

    Water enters a building at ground level through a pipe of cross-sectional area 4.0 cm24.0\ \text{cm}^2, at a speed of 1.0 m s−11.0\ \text{m s}^{-1} and a pressure of 2.0×105 Pa2.0 \times 10^5\ \text{Pa}. The pipe that supplies a bathroom 5.0 m higher up has a cross-sectional area of 2.0 cm22.0\ \text{cm}^2. Treat water as an ideal fluid of density 1000 kg m−31000\ \text{kg m}^{-3} in steady flow, and take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    (a) Find the speed of the water in the bathroom pipe.

    (b) Find the pressure in the bathroom pipe.

    (c) Which of the two changes (the rise in height or the increase in speed) is mainly responsible for the drop in pressure?

    Medium
    3 marks
  31. 31

    Question 31

    Water exists in the air both as mist droplets of radius 1.0 μm1.0\ \mu\text{m} and as raindrops of radius 2.0 mm. Take the surface tension of water as 0.0727 N m−10.0727\ \text{N m}^{-1} and Pa=1.013×105 PaP_a = 1.013 \times 10^5\ \text{Pa}.

    (a) Calculate the excess pressure inside each drop, and compare the two.

    (b) Is the pressure higher inside or outside a drop? Explain using the shape of its surface.

    (c) Use your result to explain, qualitatively, why the very smallest droplets are the hardest to form and the most easily evaporated.

    Medium
    3 marks
  32. 32

    Question 32

    A clean glass capillary tube of inner diameter 0.40 mm is dipped vertically into water. Take the surface tension of water as 0.0727 N m−10.0727\ \text{N m}^{-1}, the angle of contact as zero, the density of water 1000 kg m−31000\ \text{kg m}^{-3} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    (a) Find the height to which water rises in the tube.

    (b) The tube is now tilted so that it makes an angle of 60∘60^\circ with the vertical, its lower end still in the water. What is the vertical height of the water column now, and how long is the column measured along the tube?

    Medium
    3 marks
  33. 33

    Question 33

    A student reads the following data from Table 9.2 of the textbook:

    FluidTemperature (°C)Viscosity (mPa s)
    Water201.0
    Water1000.3
    Machine oil16113
    Machine oil3834
    Air00.017
    Air400.019

    (a) How does the viscosity of liquids and of gases change as the temperature rises?

    (b) Give a reason for the opposite behaviour of liquids and gases.

    (c) Use the data to explain why a car engine is harder to start, and wears more, on a very cold morning.

    Medium
    3 marks
  34. 34

    Question 34

    A carpenter pushes a nail into a wooden board with a force of 50 N, pressing on the head of the nail with his thumb. The point of the nail has an area of 0.10 mm20.10\ \text{mm}^2 and its head an area of 1.0 cm21.0\ \text{cm}^2. Find the pressure at the point and at the head, and explain why the point goes into the wood while the head does not hurt the thumb.

    Medium
    2 marks
  35. 35

    Question 35

    A passenger fills her fountain pen at the airport before boarding. After the aircraft has climbed to its cruising height, she finds that ink has leaked out of the nib onto her fingers. Explain why.

    Medium
    2 marks
  36. 36

    Question 36

    In a still room, the smoke from an incense stick rises as a smooth, thin thread for the first few centimetres, and then suddenly breaks up into irregular swirls. Explain this change in terms of the type of flow.

    Medium
    2 marks
  37. 37

    Question 37

    Explain how you drink juice from a glass through a straw. Suppose the same glass of juice and straw were used on the Moon, where there is practically no atmosphere (imagine the juice did not evaporate). Could you drink it in the same way? Give a reason.

    Medium
    2 marks
  38. 38

    Question 38

    When a little mercury is spilt on a table, it breaks up into tiny drops that are almost perfect spheres. A larger quantity of mercury poured in one place, however, spreads into a flattened puddle. Explain the difference.

    Medium
    2 marks
  39. 39

    Question 39

    After the rains, farmers often plough the top layer of their fields. One reason is to keep the moisture in the soil for longer. Explain how ploughing helps in this.

    Medium
    2 marks
  40. 40

    Question 40

    Raindrops often form in clouds more than 2 km above the ground. If they fell freely from this height, they would reach the ground at about 200 m s−1200\ \text{m s}^{-1}, yet even large raindrops hit us at less than about 10 m s−110\ \text{m s}^{-1}. Explain why.

    Medium
    2 marks
  41. 41

    Question 41

    A straight concrete dam is 50 m50\ \text{m} long. On one side it holds back water 6.0 m6.0\ \text{m} deep; its wet face is vertical. The engineers need the turning effect (torque) of the water about the bottom edge B of the wet face, which tends to tip the dam over. The atmosphere presses on both sides of the dam. Take ρ=1000 kg m−3\rho = 1000\ \text{kg m}^{-3} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    Class 11 Physics Mechanical Properties Of Fluids

    What is the torque of the water pressure about B?

    MCQHard
    1 mark
  42. 42

    Question 42

    An ocean-research probe collects a sample of sea water at a depth of 2000 m2000\ \text{m}. At the surface sea water has density 1030 kg m−31030\ \text{kg m}^{-3} (Table 9.1). The bulk modulus of water is 2.2×109 Pa2.2 \times 10^{9}\ \text{Pa} (Chapter 8). Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}, and for the pressure use the surface density throughout.

    What is the density of the sea water at that depth, and what does it tell you about treating liquids as incompressible?

    MCQHard
    1 mark
  43. 43

    Question 43

    A snorkeller swims face down with her chest 0.45 m0.45\ \text{m} below the surface of the sea (density 1030 kg m−31030\ \text{kg m}^{-3}). The air in her lungs is connected through the snorkel to the air above the water. Her breathing muscles can expand her chest against a pressure difference of at most 38 mm38\ \text{mm} of mercury. Take ρHg=13.6×103 kg m−3\rho_{Hg} = 13.6 \times 10^{3}\ \text{kg m}^{-3}, Pa=1.013×105 PaP_a = 1.013 \times 10^{5}\ \text{Pa} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    Which statement is correct?

    MCQHard
    1 mark
  44. 44

    Question 44

    In a hydraulic lift the small piston (area 0.0050 m20.0050\ \text{m}^2) and the large piston (area 0.10 m20.10\ \text{m}^2) are joined by a pipe full of oil of density 800 kg m−3800\ \text{kg m}^{-3}. Because of the way the machine is installed, the face of the large piston is 1.0 m1.0\ \text{m} higher than the face of the small piston. A load of 2000 kg2000\ \text{kg} rests on the large piston. Both pistons are open to the atmosphere on their outer faces; neglect the masses of the pistons and friction. Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    Class 11 Physics Mechanical Properties Of Fluids

    What force must act on the small piston to hold the load at rest?

    MCQHard
    1 mark
  45. 45

    Question 45

    A steady, smooth stream of water falls from a kitchen tap. At the mouth of the tap the stream has a radius of 0.60 cm0.60\ \text{cm} and the water moves down at 0.50 m s−10.50\ \text{m s}^{-1}. The stream stays unbroken and the air around it is at atmospheric pressure everywhere. Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    What are the speed of the water and the radius of the stream 20 cm20\ \text{cm} below the mouth of the tap?

    MCQHard
    1 mark
  46. 46

    Question 46

    Water flows steadily through a horizontal pipe whose cross-section narrows from 10 cm210\ \text{cm}^2 to 5.0 cm25.0\ \text{cm}^2. Two thin vertical tubes, open at the top, are fitted on the wide and the narrow sections. The water in the tube on the wide section stands 15 cm15\ \text{cm} higher than in the tube on the narrow section. Treat the water as an ideal fluid and take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    Class 11 Physics Mechanical Properties Of Fluids

    What volume of water flows through the pipe per second?

    MCQHard
    1 mark
  47. 47

    Question 47

    A large open water tank stands on a smooth trolley. A small hole of area 2.0 cm22.0\ \text{cm}^2 is opened in one side wall, 3.2 m3.2\ \text{m} below the water surface, and a horizontal jet streams out. The trolley is held by a horizontal spring balance. Take ρ=1000 kg m−3\rho = 1000\ \text{kg m}^{-3} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    What horizontal force must the spring balance exert to keep the tank at rest while the water level is still 3.2 m3.2\ \text{m} above the hole?

    MCQHard
    1 mark
  48. 48

    Question 48

    A tank of water is emptied with a siphon, a tube of uniform bore that rises from the tank, passes over the rim and ends at an outlet D outside. The highest point C of the tube is 0.50 m0.50\ \text{m} above the water surface in the tank and the outlet D is 1.2 m1.2\ \text{m} below that surface. The tank is wide, the flow is steady, and the water may be treated as an ideal fluid. Take Pa=1.013×105 PaP_a = 1.013 \times 10^{5}\ \text{Pa}, ρ=1000 kg m−3\rho = 1000\ \text{kg m}^{-3} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    Class 11 Physics Mechanical Properties Of Fluids

    What is the pressure of the water at C?

    MCQHard
    1 mark
  49. 49

    Question 49

    Near sea level (ρ=1.2 kg m−3\rho = 1.2\ \text{kg m}^{-3}) air flows at 80 m s−180\ \text{m s}^{-1} over the upper surface and at 70 m s−170\ \text{m s}^{-1} under the lower surface of a wing of area 30 m230\ \text{m}^2, which gives a lift of 2.7×104 N2.7 \times 10^{4}\ \text{N}. The aircraft now flies at a height where the air density is 0.90 kg m−30.90\ \text{kg m}^{-3}. Assume the pattern of the airflow round the wing stays the same, so both speeds change by the same factor, and neglect the small height difference between the two surfaces.

    By what factor must both air speeds increase for the wing to give the same lift?

    MCQHard
    1 mark
  50. 50

    Question 50

    In a cloud, tiny water droplets fall through still air at their terminal speed. Two identical droplets, each falling at terminal speed vv, collide and merge into a single spherical drop. Stokes' law holds for both the small and the merged drops, and the density of the air is negligible compared with that of water.

    What is the terminal speed of the merged drop?

    MCQHard
    1 mark
  51. 51

    Question 51

    A steel ball of radius 2.5 mm2.5\ \text{mm} (density 7.8×103 kg m−37.8 \times 10^{3}\ \text{kg m}^{-3}) is dropped into a tall jar of castor oil (density 960 kg m−3960\ \text{kg m}^{-3}, viscosity 0.70 Pa s0.70\ \text{Pa s}) and soon falls at its terminal speed. Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    At what rate is heat produced in the oil while the ball falls at its terminal speed?

    MCQHard
    1 mark
  52. 52

    Question 52

    A metal block of mass 2.0 kg2.0\ \text{kg} slides down a plane inclined at 30∘30^\circ to the horizontal. Its flat face, of area 0.050 m20.050\ \text{m}^2, is separated from the plane by a uniform film of oil 0.10 mm0.10\ \text{mm} thick, so the block never touches the plane. The block slides at a constant speed of 0.50 m s−10.50\ \text{m s}^{-1}. Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2} and assume the speed of the oil varies uniformly across the film.

    What is the coefficient of viscosity of the oil, and at what steady speed would the block slide if the film of the same oil were 0.20 mm0.20\ \text{mm} thick?

    MCQHard
    1 mark
  53. 53

    Question 53

    To find the excess pressure inside a small water drop of radius 0.80 mm0.80\ \text{mm}, a student imagines pumping a little more water into it, so that its radius grows by Δr=1.0×10−6 m\Delta r = 1.0 \times 10^{-6}\ \text{m}. The work done by the excess pressure in pushing in the extra volume must equal the extra surface energy of the drop. Take S=0.0727 N m−1S = 0.0727\ \text{N m}^{-1}.

    What is the extra surface energy ΔW\Delta W, and what excess pressure ΔP\Delta P does this argument give?

    MCQHard
    1 mark
  54. 54

    Question 54

    A child blows two soap bubbles, of radii 3.0 cm3.0\ \text{cm} and 4.0 cm4.0\ \text{cm}, which touch and stick together, so that a single curved soap film separates the air inside one bubble from the air inside the other. Both bubbles are made of the same soap solution and are surrounded by the atmosphere.

    What is the radius of curvature of the common film, and which way does it bulge?

    MCQHard
    1 mark
  55. 55

    Question 55

    A clean glass capillary tube of inner radius 0.40 mm0.40\ \text{mm} is dipped vertically into water (S=0.0727 N m−1S = 0.0727\ \text{N m}^{-1}, angle of contact 0∘0^\circ, ρ=1000 kg m−3\rho = 1000\ \text{kg m}^{-3}), and the water climbs to its equilibrium height hh. Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2} and neglect the small volume of water in the meniscus.

    Which statement about the energy in this rise is correct?

    MCQHard
    1 mark
  56. 56

    Question 56

    A sealed glass box contains a beaker of water with a clean glass capillary tube, 20 cm20\ \text{cm} long, standing upright in it. The water in the tube stands 7.4 cm7.4\ \text{cm} above the water in the beaker. The box is then released and falls freely (assume the fall lasts long enough for the water to settle and air resistance is negligible).

    Which statement correctly describes what happens to the water in the tube during the fall?

    MCQHard
    1 mark
  57. 57

    Question 57

    Two clean, flat glass plates are held vertical and parallel, 0.15 mm0.15\ \text{mm} apart, with their lower edges dipped in water (S=0.0727 N m−1S = 0.0727\ \text{N m}^{-1}, angle of contact 0∘0^\circ, ρ=1000 kg m−3\rho = 1000\ \text{kg m}^{-3}). Water rises into the narrow gap between them. The plates are wide, so the effects at their side edges can be neglected. Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    Class 11 Physics Mechanical Properties Of Fluids

    How high does the water rise in the gap?

    MCQHard
    1 mark
  58. 58

    Question 58

    A pump draws water from a still pond and delivers it through a pipe to a nozzle 15 m15\ \text{m} above the pond surface. The water leaves the nozzle, of area 5.0 cm25.0\ \text{cm}^2, at 10 m s−110\ \text{m s}^{-1} into the open air. Neglect viscous losses in the pipe and take ρ=1000 kg m−3\rho = 1000\ \text{kg m}^{-3} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    What is the least power the pump must deliver to the water?

    MCQHard
    1 mark
  59. 59

    Question 59

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): A wide open tank of water and an identical wide open tank of mercury are filled to the same depth. Jets from small holes at the same depth below the free surface in the two tanks leave with the same speed.

    Reason (R): The gauge pressure at a given depth in mercury is about 13.6 times the gauge pressure at the same depth in water.

    MCQHard
    1 mark
  60. 60

    Question 60

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): Adding a detergent to water increases its angle of contact with the fibres of a cloth, so the water spreads into the fibres less easily.

    Reason (R): A liquid wets a solid when its angle of contact with the solid is obtuse.

    MCQHard
    1 mark
  61. 61

    Question 61

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): For a small right-angled prism of liquid inside a liquid at rest, the pressure on its sloping face is equal to the pressure on its vertical face.

    Reason (R): The force exerted by the surrounding liquid on each face of the prism is parallel to that face.

    MCQHard
    1 mark
  62. 62

    Question 62

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): The angle of contact of water is the same on clean glass as on a waxed surface, because it depends only on the liquid.

    Reason (R): The angle of contact is fixed by the liquid–air surface tension SlaS_{la} alone.

    MCQHard
    1 mark
  63. 63

    Question 63

    A pressurised water tank. A closed tank stands on legs. The water in it is 1.5 m1.5\ \text{m} above a small hole of area 1.0 cm21.0\ \text{cm}^2 in a side wall, and the hole is 1.0 m1.0\ \text{m} above level ground. The air trapped above the water is kept at an absolute pressure of 2.5×105 Pa2.5 \times 10^{5}\ \text{Pa} by a pump. The tank is wide compared with the hole. Take Pa=1.013×105 PaP_a = 1.013 \times 10^{5}\ \text{Pa}, ρ=1000 kg m−3\rho = 1000\ \text{kg m}^{-3} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}, and neglect air resistance.

    Class 11 Physics Mechanical Properties Of Fluids

    (a) Find the speed with which water leaves the hole. Which contributes more to this speed, the depth of the hole or the pressure of the trapped air?

    (b) Find the volume of water leaving per second, and the time to fill a 100 L100\ \text{L} drum from the jet.

    (c) How far from the wall of the tank does the jet strike the ground? What would this distance be if the lid were opened, with the depth still 1.5 m1.5\ \text{m}?

    (d) To what absolute pressure must the air above the water be raised to double the distance found in (c), with the depth unchanged?

    Hard
    5 marks
  64. 64

    Question 64

    Why muddy water stays cloudy. After a storm, a still pond 2.0 m2.0\ \text{m} deep is stirred up with fine sand grains of radius 0.050 mm0.050\ \text{mm} and clay particles of radius 1.0 μm1.0\ \mu\text{m}. Both are made of mineral of density 2600 kg m−32600\ \text{kg m}^{-3}. For water take η=1.0×10−3 Pa s\eta = 1.0 \times 10^{-3}\ \text{Pa s} and σ=1000 kg m−3\sigma = 1000\ \text{kg m}^{-3}, and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}. Treat the particles as spheres that obey Stokes' law and reach their terminal speed almost at once.

    Class 11 Physics Mechanical Properties Of Fluids

    (a) Find the terminal speed of a sand grain and the time it takes to settle from the surface to the bottom.

    (b) Find the viscous drag on a sand grain at its terminal speed. What fraction of the grain's weight is this, and why is it not the whole weight?

    (c) Without repeating the full calculation, find the terminal speed of a clay particle and the time, in days, that it takes to settle through the pond.

    (d) Explain why the pond clears of sand within minutes but stays cloudy for days. Water-treatment plants add a chemical that makes the fine particles stick together into clumps. Explain why this clears the water much faster.

    Hard
    5 marks
  65. 65

    Question 65

    Roofs in a cyclone. During a cyclone a wind of 40 m s−140\ \text{m s}^{-1} blows horizontally over the flat roof of a house. The roof has an area of 150 m2150\ \text{m}^2 and a mass of 8000 kg8000\ \text{kg}, and simply rests on the walls without being fixed. The windows are shut, so the air inside is still and at the pressure of the still air outside. Take the density of air as 1.2 kg m−31.2\ \text{kg m}^{-3} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    Class 11 Physics Mechanical Properties Of Fluids

    (a) Find the difference between the air pressure below and above the roof.

    (b) Find the net vertical force on the roof. Will the roof be lifted off?

    (c) What is the least wind speed at which the roof would just be lifted?

    (d) State the assumptions you made in applying Bernoulli's principle and comment on whether each is reasonable here.

    Hard
    5 marks
  66. 66

    Question 66

    Inside a capillary tube. A clean glass capillary tube of inner radius 0.25 mm0.25\ \text{mm} stands vertically in water at 20 ∘C20\ ^\circ\text{C}. The angle of contact is 0∘0^\circ, the surface tension of water is 0.0727 N m−10.0727\ \text{N m}^{-1} and its density 1000 kg m−31000\ \text{kg m}^{-3}. Point A is in the water just below the meniscus. Take Pa=1.013×105 PaP_a = 1.013 \times 10^{5}\ \text{Pa} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}, and neglect the small volume of water in the meniscus.

    Class 11 Physics Mechanical Properties Of Fluids

    (a) Find the height hh to which the water rises in the tube.

    (b) Find the pressure at point A, and explain why it is less than atmospheric pressure.

    (c) Find the mass of water raised in the tube, and show that its weight equals the upward force of surface tension at the edge of the meniscus.

    (d) What inner radius would a glass capillary need for water at 20 ∘C20\ ^\circ\text{C} to rise 10 cm10\ \text{cm} in it? Near its boiling point water has S=0.0589 N m−1S = 0.0589\ \text{N m}^{-1} and ρ=958 kg m−3\rho = 958\ \text{kg m}^{-3}. Both are smaller than at 20 ∘C20\ ^\circ\text{C}, and they appear in opposite places in the formula. Does hot water rise higher or lower in the original tube? Justify with a calculation.

    Hard
    5 marks
  67. 67

    Question 67

    Forces on a water tank. A vertical cylindrical water tank of radius 0.50 m0.50\ \text{m} stands on the ground and holds water 2.0 m2.0\ \text{m} deep. Its top is open to the atmosphere, which also surrounds the tank. Take ρ=1000 kg m−3\rho = 1000\ \text{kg m}^{-3} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}, and work with gauge pressures.

    (a) Find the force of the water on the base of the tank.

    (b) Explain why the average gauge pressure on the curved side wall is half the pressure at the base, and hence find the total outward force of the water on the curved wall (the sum of the magnitudes of the forces on all its parts).

    (c) Show that the total outward force on the curved wall equals the force on the base only when the depth equals the radius of the tank.

    (d) The same volume of water is poured instead into a tank of radius 1.0 m1.0\ \text{m}. Find the new depth, the force on the base and the total outward force on the curved wall, and explain why spreading the water out reduces the load on the wall.

    Hard
    4 marks
  68. 68

    Question 68

    To measure the small gauge pressure of the gas supply in a laboratory, a technician uses a manometer whose open arm is a glass tube inclined at 10∘10^\circ to the horizontal, connected to a wide reservoir of ethyl alcohol (density 806 kg m−3806\ \text{kg m}^{-3}). The gas is connected to the reservoir, and the alcohol is pushed 12.0 cm12.0\ \text{cm} up the tube, measured along the tube. The reservoir is so wide that its level hardly changes. Take ρHg=13.6×103 kg m−3\rho_{Hg} = 13.6 \times 10^{3}\ \text{kg m}^{-3} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    Class 11 Physics Mechanical Properties Of Fluids

    (a) Find the vertical rise of the alcohol and the gauge pressure of the gas.

    (b) What reading would an ordinary vertical mercury manometer give for this pressure? By what factor does the inclined alcohol manometer magnify the reading?

    (c) The barometer reads 75.6 cm75.6\ \text{cm} of mercury. Find the absolute pressure of the gas.

    Hard
    3 marks
  69. 69

    Question 69

    A wide open tank holds water 2.0 m2.0\ \text{m} deep above a horizontal outlet pipe at its base. The pipe has a narrow section of area 2.0 cm22.0\ \text{cm}^2 and then widens to 4.0 cm24.0\ \text{cm}^2 where it ends in the open air. A thin vertical side tube joins the narrow section from below and dips into a basin of water underneath. Treat the water as an ideal fluid; take Pa=1.013×105 PaP_a = 1.013 \times 10^{5}\ \text{Pa}, ρ=1000 kg m−3\rho = 1000\ \text{kg m}^{-3} and g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    Class 11 Physics Mechanical Properties Of Fluids

    (a) Find the speed of the water at the exit and in the narrow section, and the pressure in the narrow section.

    (b) How high above the water in the basin could the water in the side tube be drawn up?

    (c) If the depth of water in the tank were increased, the pressure in the narrow section would fall further. At what depth would it fall to zero?

    Hard
    3 marks
  70. 70

    Question 70

    A thin plate of area 0.10 m20.10\ \text{m}^2 rests on two layers of liquid that do not mix (the denser one below), lying on a fixed flat surface. The lower layer, 1.0 mm1.0\ \text{mm} thick, has viscosity 0.20 Pa s0.20\ \text{Pa s}; the upper layer, also 1.0 mm1.0\ \text{mm} thick, has viscosity 0.60 Pa s0.60\ \text{Pa s}. The plate is pulled horizontally with a steady force of 3.0 N3.0\ \text{N} and moves at a constant speed. The speed changes uniformly across each layer.

    Class 11 Physics Mechanical Properties Of Fluids

    (a) Show that the shearing stress is the same in both layers, and find it.

    (b) Find the velocity gradient in each layer.

    (c) Find the speed of the interface between the layers and the speed of the plate.

    Hard
    3 marks
  71. 71

    Question 71

    Two soap bubbles, of radii 1.0 cm1.0\ \text{cm} and 3.0 cm3.0\ \text{cm}, are blown at the two ends of a narrow tube fitted with a closed tap in the middle. The surface tension of the soap solution is 0.025 N m−10.025\ \text{N m}^{-1}.

    (a) Find the excess pressure inside each bubble.

    (b) Describe what happens when the tap is opened, and explain why.

    (c) When does the process stop?

    Hard
    3 marks
  72. 72

    Question 72

    A drop of liquid rests on a flat solid surface. The surface tensions (energies per unit area) of the three interfaces are: liquid–air Sla=0.072 N m−1S_{la} = 0.072\ \text{N m}^{-1}, solid–air Ssa=0.110 N m−1S_{sa} = 0.110\ \text{N m}^{-1} and solid–liquid Ssl=0.074 N m−1S_{sl} = 0.074\ \text{N m}^{-1}.

    (a) Find the angle of contact.

    (b) A coating is applied to the solid which leaves SsaS_{sa} unchanged but raises SslS_{sl} to 0.146 N m−10.146\ \text{N m}^{-1}. Find the new angle of contact, and describe how the drop's shape and behaviour change on the coated surface.

    (c) Back on the uncoated surface, a detergent is added to the liquid; suppose it lowers SlaS_{la} to 0.040 N m−10.040\ \text{N m}^{-1} and SslS_{sl} to 0.050 N m−10.050\ \text{N m}^{-1}, with SsaS_{sa} unchanged. What happens to the drop now?

    Hard
    3 marks
  73. 73

    Question 73

    An open cylindrical tank of cross-sectional area 0.50 m20.50\ \text{m}^2 holds water 1.8 m1.8\ \text{m} deep. A hole of area 1.0 cm21.0\ \text{cm}^2 is opened in its flat bottom. Assume Torricelli's law holds at every moment (the tank is much wider than the hole) and take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    (a) Show that the time taken for the depth to fall from HH to yy is t=Aa2g(H−y)t = \dfrac{A}{a}\sqrt{\dfrac{2}{g}}\left(\sqrt{H} - \sqrt{y}\right), and find the time to empty the tank.

    (b) Find the time taken for the first half of the water to drain out.

    (c) Explain why the second half takes so much longer than the first.

    Hard
    3 marks
  74. 74

    Question 74

    An aircraft leaves the ground when the speed of the air flowing past its wings reaches 70 m s−170\ \text{m s}^{-1}, because only then is the lift, which depends on the airspeed, equal to its weight. On its take-off run it speeds up along the runway with a constant acceleration. When a wind blows along the runway, the airspeed (the speed of the air flowing past the wings) is not the same as the ground speed.

    (a) Take the lift to be proportional to the square of the airspeed. On a still day, what fraction of its weight is the lift when the airspeed is 50 m s−150\ \text{m s}^{-1}, and at what airspeed is the lift 90%90\% of the weight?

    (b) Taking off into the wind on a windy day, the aircraft reaches the lift-off airspeed of 70 m s−170\ \text{m s}^{-1} when its ground speed is only 60 m s−160\ \text{m s}^{-1}. Compare the length of runway needed with that needed on a still day.

    (c) With the same wind behind it, the aircraft needs a ground speed of 80 m s−180\ \text{m s}^{-1} to reach that airspeed. Compare the runway needed with that on a still day, and hence explain why pilots take off into the wind.

    Hard
    3 marks
  75. 75

    Question 75

    In steady flow, the velocity of the fluid at every point of space does not change with time. A student concludes that in steady flow no particle of the fluid can ever accelerate. Using water flowing steadily through a pipe that narrows, explain why the student is wrong, and say what provides the force that accelerates the water.

    Hard
    2 marks
  76. 76

    Question 76

    A small air bubble of radius 0.50 mm0.50\ \text{mm} is trapped in a tall jar of glycerine (density 1260 kg m−31260\ \text{kg m}^{-3}, viscosity 0.83 Pa s0.83\ \text{Pa s}). A student substitutes into vt=2a2(ρ−σ)g9ηv_t = \dfrac{2a^2(\rho - \sigma)g}{9\eta}, with ρ≈1.3 kg m−3\rho \approx 1.3\ \text{kg m}^{-3} for the air, and gets vt=−8.26×10−4 m s−1v_t = -8.26 \times 10^{-4}\ \text{m s}^{-1}. Explain what the minus sign means, which forces act on the bubble when it moves steadily, and why it moves so slowly.

    Hard
    2 marks
  77. 77

    Question 77

    Two matchsticks lie parallel on the surface of clean water in a dish, about 1 cm1\ \text{cm} apart. A drop of soap solution is touched to the water between them. Predict how the matchsticks move, and explain why using the idea of surface tension as a force per unit length.

    Hard
    2 marks
  78. 78

    Question 78

    Why does hot water clean greasy dishes better than cold water, even before any soap is added? Give two reasons based on the properties of liquids studied in this chapter.

    Hard
    2 marks
  79. 79

    Question 79

    Over a few hours the mercury barometer in a weather station falls by 10 mm10\ \text{mm}. Find this fall in pascals and as a percentage of normal atmospheric pressure, state how high one would have to climb, in air of density about 1.2 kg m−31.2\ \text{kg m}^{-3}, to see the same fall, and explain what the fall tells you about the air above the station.

    Hard
    2 marks
  80. 80

    Question 80

    In a car's hydraulic brakes, the four wheel pistons, each of area 7.07 cm27.07\ \text{cm}^2, must each move out by 1.0 mm1.0\ \text{mm} to press the pads on. Explain why the brake fluid can be treated as incompressible but air cannot, and why a bubble of air of about 1 cm31\ \text{cm}^3 trapped in the brake line makes the brakes dangerous.

    Hard
    2 marks