Opening your dashboard
Class 11 Physics Chapter 10 Thermal Properties Of Matter: Competency-Based Questions (CBQ)
80 questions on Chapter 10, each worked through on its own page with the AI tutor. Class 11 Physics, CBSE 2026-27.
80 questions
1–5 marks · Mixed difficulty
- 11 mark
Question 1
A school nurse checks a cheap glass thermometer before using it. Placed in melting ice it reads , and placed in steam above boiling water at 1 atm it reads . Its scale is uniform and its column rises evenly with temperature. Later the thermometer reads when held in a child's mouth. What is the child's true temperature?
- 21 mark
Question 2
An oven has a digital display that can show its temperature in either Celsius or Fahrenheit. While setting it, a cook notices that at one particular setting the Fahrenheit number shown is exactly twice the Celsius number. What is the oven temperature at that setting, in degrees Celsius?
- 31 mark
Question 3
On a cold morning at , a driver inflates her car tyres to a gauge pressure of . After a long drive on a hot road, the air in the tyres is at . Atmospheric pressure is . Treating the air as an ideal gas and the volume of the tyre as unchanged, what will her gauge now read?
- 41 mark
Question 4
A student traps some air in a syringe whose piston moves freely, so the air stays at atmospheric pressure, and warms it gently from room temperature, . She wants to compare how readily the air expands with how readily mercury expands (). Treating the air as an ideal gas, what is the coefficient of volume expansion of the air at , and how does it compare with that of mercury?
- 51 mark
Question 5
A railway line is being laid with separate steel rails, each 12.5 m long, on a day when the temperature is . On the hottest summer days the rails reach . The engineer must leave a gap between the ends of neighbouring rails so that they just touch on the hottest day. Taking for steel, what is the least gap that must be left at each joint?
- 61 mark
Question 6
An old pendulum clock in a hall has a brass pendulum rod () and keeps perfect time when the hall is at . During a heat wave the hall stays at all day. Treating the pendulum as a simple pendulum whose length is that of the rod, how does the clock behave over one full day?
- 71 mark
Question 7
An engine designer needs the density of an aluminium piston at its working temperature. At aluminium has a density of , and its coefficient of linear expansion is . What is the density of the piston when it is at ?
- 81 mark
Question 8
A glazier fits a sheet of ordinary glass 1.20 m wide into an aluminium window frame on a summer afternoon at . On winter nights the window cools to , and the frame must never squeeze the glass. For aluminium , and for ordinary glass . What is the least total clearance across the width that he must leave between the glass and the frame?
- 91 mark
Question 9
In a severe winter, the surface of a deep mountain lake has frozen over, but fish are still swimming near the bottom. A diver lowers a thermometer to the bed of the lake. Which reading should she expect, and why?
- 101 mark
Question 10
A cook heats of water from to boiling () in a heavy aluminium pot of mass on a electric hot plate. Specific heats: water , aluminium . Assuming all the heat from the plate goes into the pot and the water, how long does it take to bring the water to the boil?
- 111 mark
Question 11
On a sunny morning at the coast, equal masses of sea water and of dry soil absorb equal amounts of heat from the Sun. The soil warms by . Taking the specific heat of water as and that of dry soil as about , and ignoring any heat lost, by how much does the water warm?
- 121 mark
Question 12
A student pours of water at into a calorimeter that holds of water at . The calorimeter itself, also at , has a water equivalent of (it takes as much heat as 20 g of water to warm by the same amount). Assuming no heat is lost to the surroundings, what is the final temperature of the mixture?
- 131 mark
Question 13
A café wants to make iced tea quickly. It takes of freshly made tea at and drops in ice cubes at until the drink settles at with all the ice melted. Treat the tea as water (), take , and ignore heat taken by the glass and the air. What mass of ice is needed?
- 141 mark
Question 14
A careless cook's hand is caught in a puff of steam from a pressure cooker. About of steam at condenses on her skin and the water formed cools to skin temperature, . Compare this with of boiling water at spilled on the skin and cooling to . Taking and , about how many times as much heat does the steam deliver to the skin?
- 151 mark
Question 15
In a laboratory, one end of a copper rod is kept in a chamber of steam at and the other end is buried in melting ice at , as shown in the figure. The rod is 1.0 m long, has a cross-sectional area of , and is lagged so that no heat escapes from its sides. Take for copper and . Once the flow is steady, how much ice melts in one hour?

- 161 mark
Question 16
A blackened metal plate on a laboratory stand is held at by an electric heater, and loses energy by radiation to the walls of the room at at a net rate . The heater is turned up until the plate is at ; the room stays at . Treating the plate as a black body, what is its net rate of loss by radiation now?
- 171 mark
Question 17
A machinist cuts a square aluminium plate exactly for a heating unit. In use the plate runs hotter than when it was cut, and the designer must know how much its face grows to allow room around it. Taking for aluminium, by how much does the area of the plate's face increase?
- 181 mark
Question 18
A long-distance swimmer in cool water keeps warm partly because of a layer of fat under the skin. Suppose the body loses heat only by conduction through this layer, of area , with its inner face at and its outer face at . Body fat has thermal conductivity (Table 10.6). What is the least thickness of fat for which the heat conducted through it is no more than ?
- 191 mark
Question 19
Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.
Assertion (A): In very cold regions, a thick layer of fresh snow lying on a field makes the soil underneath freeze harder than bare soil would, because the snow, being at or below , draws heat out of the soil.
Reason (R): Fresh snow is made of ice crystals, so it conducts heat about as well as a solid block of ice does.
- 201 mark
Question 20
Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.
Assertion (A): If water at is warmed slowly to , its volume decreases.
Reason (R): Water has the largest specific heat capacity of all the substances listed in Table 10.3 of the textbook.
- 211 mark
Question 21
Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.
Assertion (A): Constant-volume gas thermometers filled with different gases (say, hydrogen, nitrogen and oxygen) give nearly the same reading for the same temperature, provided each gas is at a low density.
Reason (R): Every real gas obeys the equation exactly, at all pressures.
- 221 mark
Question 22
Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.
Assertion (A): While a block of ice is melting at under atmospheric pressure, its temperature stays at even though heat is being supplied to it steadily.
Reason (R): The latent heat of fusion of ice is smaller than the latent heat of vaporisation of water.
- 235 marks
Question 23
After a snowfall, a flat roof of area is covered by a layer of snow deep, of density , at , as shown in the figure. Sunlight falls on the roof at , but clean snow reflects most of it and absorbs only . Take and , and ignore all other gains and losses of heat.

(a) Find the mass of snow on the roof.
(b) How much heat is needed to warm all this snow to and melt it completely?
(c) How many hours of sunshine are needed to melt it?
(d) Soot from a nearby chimney settles on the snow, so it now absorbs of the sunlight. How long does the melting take now? Use your answer to explain why dirty snow melts faster than clean snow.
- 245 marks
Question 24
As the climate warms, the oceans take up heat and the water in them expands, raising the sea level. Treat a stretch of ocean as a layer of water of depth in a basin whose surface area cannot change, because the basin's sides are fixed by the coastline.
(a) Show that when the water warms by , its depth increases by .
(b) Suppose only the top of the ocean warms, by . Taking for water (Table 10.2), find the rise in sea level.
(c) A student uses the linear coefficient in (b) and gets . Explain why this is wrong.
(d) The deep ocean is at only a few degrees Celsius. Explain why warming this cold deep water by the same raises the sea level far less than warming the surface water.
- 255 marks
Question 25
A room has a window 1.0 m high and 1.5 m wide. On a winter day the inner surface of the window is at and the outer surface at . Glass has thermal conductivity and still air . The figure shows the two designs being considered.

(a) Find the rate of flow of heat through a single pane of glass 4.0 mm thick.
(b) In practice, when the room air is at and the outdoor air at , a single pane loses much less heat than your answer to (a). Suggest why.
(c) In double glazing, two 4.0 mm panes are separated by a 10 mm layer of still air. With the same two outer surface temperatures, find the rate of flow of heat, and compare it with (a).
(d) Across which layer does most of the temperature drop occur in the double-glazed window? Find the drop across it.
- 265 marks
Question 26
The Sun's spectrum is most intense at a wavelength of about . The radius of the Sun is , and the Earth is away from it. Treat the Sun and the Earth as black bodies. Take Wien's constant and .
(a) Estimate the temperature of the Sun's surface.
(b) Find the total power radiated by the Sun.
(c) Find the power falling on each square metre of a surface facing the Sun at the Earth's distance (ignore the atmosphere).
(d) The Earth absorbs sunlight on its cross-section but radiates from its whole surface . Find the temperature at which the Earth would radiate away exactly what it absorbs, and comment on your answer, given that the Earth's actual average surface temperature is about .
- 274 marks
Question 27
A flask of hot water at is left to cool in a room at , and it reaches after . Assume that Newton's law of cooling holds throughout, in the form , where is the temperature of the water and that of the room.
(a) Find the constant .
(b) How long after it was left does the water reach ?
(c) Estimate the same time using the average-temperature method (rate of fall of temperature average excess temperature over each interval), and compare the two answers.
- 283 marks
Question 28
A company makes liquid-in-glass thermometers and must choose the liquid for each product. Table 10.5 gives: mercury melts at and boils at ; ethanol melts at and boils at (at 1 atm).
(a) Which liquid should be used in a thermometer for a research station in Antarctica, where winter temperatures fall to ? Why not the other?
(b) Which liquid should be used in a cook's thermometer for boiling sugar syrup up to ? Why not the other?
(c) Mercury boils at at 1 atm, yet some mercury thermometers read up to about . How is this possible?
- 293 marks
Question 29
A hospital oxygen cylinder has an internal volume of . When delivered, the gas in it is at and an absolute pressure of . After a few days of use, the pressure has fallen to , again at . Treat oxygen as an ideal gas with molar mass , and take .
(a) How many moles, and what mass, of oxygen did the full cylinder contain?
(b) What mass of oxygen has been used?
- 303 marks
Question 30
A car's steel petrol tank holds exactly at , and it is filled to the brim with petrol at that temperature early in the morning. The car is then parked in the sun, and the tank and the petrol both warm to . For steel , and for petrol .
(a) How much petrol overflows from the tank?
(b) A student says the answer is . What has she forgotten, and why does it make only a small difference here?
- 313 marks
Question 31
A car engine must get rid of heat into its cooling liquid at a rate of . The liquid is pumped through the engine and is allowed to warm by as it passes through, before being cooled again in the radiator.
(a) What mass of water must be pumped through the engine each second? ()
(b) What mass per second would be needed if edible oil () were used instead?
(c) Use your answers to explain why water is used as the coolant.
- 323 marks
Question 32
A sample of a solid at is heated in an insulated container by a heater, and its temperature is recorded every few seconds. The graph of temperature against time is shown in the figure. Assume all the heater's energy goes into the sample.

Using the graph, find:
(a) the specific heat capacity of the solid;
(b) its latent heat of fusion;
(c) the specific heat capacity of the liquid, and which substance the sample could be.
- 333 marks
Question 33
A steel cooking pan has a base 4.0 mm thick. A more expensive pan has a base of the same total thickness made of 2.0 mm of copper bonded under 2.0 mm of steel, as shown in the figure. In use, the outer surface of each base is hotter than its inner surface. Take for steel and for copper.

(a) Find the rate of flow of heat per square metre through each base.
(b) Apart from passing more heat, why does a copper layer help food cook evenly when the flame heats only the middle of the base?
- 342 marks
Question 34
A student wants the temperature of of warm water in a small test tube. He uses a large laboratory thermometer that has been lying on a cold bench, and leaves it in the water until the reading stops changing. The reading is noticeably lower than the temperature the water had before the thermometer went in. Explain why, and say what kind of thermometer he should have used.
- 352 marks
Question 35
A lineman notices that the overhead electric wires between two poles hang lower on a hot summer afternoon than on a cold winter morning. He is told that when new wires are strung in summer, they must be left with a definite sag rather than pulled tight. Explain both observations.
- 362 marks
Question 36
A student pours boiling water into a thick jar of ordinary glass, and the jar cracks. Her friend pours boiling water into a pyrex beaker of the same thickness without any trouble. Explain why. (Table 10.2: is for ordinary glass and for pyrex glass.)
- 372 marks
Question 37
A trekking group camping high in the mountains finds that their rice takes much longer to cook in an open pot than it does at home, even though the water is boiling vigorously. Back home, the same rice cooks in a few minutes in a pressure cooker. Explain both observations.
- 382 marks
Question 38
A vacuum flask keeps tea hot for many hours in winter, and the same flask keeps iced water cold on a summer picnic. It has a double glass wall with a vacuum between, both walls silvered, held in its case on insulating supports and closed with a cork stopper. Explain how these features reduce the transfer of heat by each of the three modes, and why the same flask works in both directions.
- 392 marks
Question 39
A family installs a split air conditioner for summer and keeps an electric room heater for winter. The installer mounts the air conditioner high up on the wall, near the ceiling, but advises them to keep the heater on the floor. Explain this advice in terms of how heat is transferred in the room.
- 402 marks
Question 40
In many homes, drinking water in summer is kept in an unglazed earthen pot (a matka), and on journeys people wrap their water bottle in a wet cloth. In both cases the water stays noticeably cooler than the air. Explain how this happens, and why it works better on a dry, breezy day than on a humid, still day.
- 411 mark
Question 41
A data logger in a school laboratory shows temperature on its own linear scale X. When it was calibrated at standard atmospheric pressure, its probe read in melting ice and in steam from boiling water. A student keeps an ordinary Celsius thermometer beside the probe and notices that, at one particular temperature, both instruments show the same number. Later in the experiment the logger's reading rises by X-degrees.
At what temperature do the two readings agree, and by how many kelvin did the temperature rise later?
- 421 mark
Question 42
Two rigid steel vessels of volumes and are joined by a thin tube of negligible volume. They contain air at and . The vessel is now placed in an oven and kept at , while the vessel is kept at . Treat air as an ideal gas and take .
When conditions are steady, what is the pressure in the vessels, and how much air has passed through the tube?
- 431 mark
Question 43
A steel rod and a copper rod of the same length and the same cross-section are joined end to end and fitted exactly, without stress, between two rigid walls. Both rods are then heated by . For steel, and ; for copper, and .

What is the thermal stress in the rods, and which way does the junction between them move?
- 441 mark
Question 44
Figure 10.6 of the text shows that the expansion coefficient of a metal is not constant but rises with temperature. For a certain alloy, over the range to ,
where is the Celsius temperature. A rod of this alloy is exactly long at . A designer needs its increase in length when it is heated to .
What is the increase in length?
- 451 mark
Question 45
A thermometer maker fills a bulb of ordinary glass, of internal volume at , with mercury; the mercury just reaches the bottom of a capillary of uniform bore . Use Table 10.2: of mercury and of ordinary glass . Neglect the change in the bore of the capillary.
How far apart must the and marks be on the stem?
- 461 mark
Question 46
Two steel balls () placed side by side in a heat-treatment furnace have the same outer radius, . One is solid. The other is a hollow shell with a concentric spherical cavity of radius . Both are heated uniformly by .
Which statement is correct?
- 471 mark
Question 47
A immersion heater warms of water in a thin plastic jug (neglect the heat capacity of the jug and the heater; ). When the water is above room temperature, it is warming at per minute. Assume that the rate at which the water loses heat to the room is proportional to its excess temperature over the room, at all the temperatures involved.
If the same water were heated by a heater instead, at what excess temperature above the room would it finally stay steady?
- 481 mark
Question 48
A student is testing three non-reacting liquids A, B and C, kept at , and respectively. When equal masses of A and B are mixed, the mixture settles at . When equal masses of B and C are mixed, the mixture settles at . Neglect heat exchange with the container and the surroundings.
What temperature will a mixture of equal masses of A and C reach?
- 491 mark
Question 49
In an experiment on mixtures, of crushed ice at is placed in a vacuum flask of negligible heat capacity, and of steam at is passed in, all of which condenses. Take , , and .
What is the final state of the contents?
- 501 mark
Question 50
A chemist has a flask containing of one of the gases listed in Table 10.4 (helium, hydrogen, nitrogen, oxygen or carbon dioxide). At its pressure is . The flask is then heated to with its stopcock open to the atmosphere, so that the pressure stays at while some gas escapes. Treat the gas as ideal, neglect the expansion of the flask, and take .
Which gas is it, and what mass of it is left in the flask at ?
- 511 mark
Question 51
In a heat-exchanger, a copper rod () and a steel rod () of the same length and the same cross-section run side by side, each with one end in a tank of boiling water and the other end in a tank of melting ice. Their sides are lagged. An engineer wants to replace the pair by a single rod of the same length and of double the cross-section that carries the same total heat current.
What thermal conductivity must the single rod have, and what fraction of the heat does the copper rod carry in the original pair?
- 521 mark
Question 52
On a still winter night the air above a pond stays at . A layer of ice thick has already formed. Assume that the upper surface of the ice is at the air temperature, the water just below the ice is at , and that the latent heat released as water freezes at the bottom of the layer escapes only by conduction up through the ice. For ice take , and .

How much longer will it take for the ice to become thick?
- 531 mark
Question 53
A small blackened body is kept at by an electric heater inside a large enclosure. A sensor shows that the body's net rate of loss of heat by radiation is exactly half of the power it emits.
What is the temperature of the enclosure walls, and what fraction of the emitted power will be the net loss if the walls are then cooled to (the body still at )?
- 541 mark
Question 54
Two stars are treated as black bodies. Star A has surface temperature and radius . Star B, a cooler giant, has surface temperature and radius . Take .
How does the total power radiated by B compare with that radiated by A, and how does the wavelength of B's most intense radiation, , compare with ?
- 551 mark
Question 55
To estimate the specific heat of an oil X (density ), a student fills two identical thin, polished cans with equal volumes, one of water (density , ) and one of oil X. Both are heated, and placed in the same draught-free room. The water takes to cool from to ; the oil takes to cool over the same range. Neglect the heat capacity of the cans.
What is the specific heat of oil X?
- 561 mark
Question 56
A small spherical laboratory oven has an inner surface of radius , covered by a shell of glass wool () of outer radius . In the steady state the inner surface of the shell is at and its outer surface at .

What power must the oven's heater supply to keep these temperatures steady?
- 571 mark
Question 57
A chimney draws well because the hot gas in its flue is less dense than the air outside. Treat the flue gas as air at , and the outside air as air at , both at the same pressure, and treat air as an ideal gas. A student uses the volume expansion coefficient of an ideal gas, , its value at (the text quotes it rounded, as ).
By what percentage is the flue gas less dense than the outside air?
- 581 mark
Question 58
A sealed rigid steel cylinder holds of helium and of nitrogen (molar masses and ). An electric heater warms the gas mixture by . Neglect the heat taken by the cylinder. Use Table 10.4: molar specific heats (in ) helium , ; nitrogen , .
How much heat does the gas mixture take in?
- 591 mark
Question 59
Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.
Assertion (A): When a mercury-in-glass thermometer is put into hot water, the mercury column first falls slightly and then rises.
Reason (R): The glass bulb is heated and expands before the heat reaches the mercury inside it.
- 601 mark
Question 60
Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.
Assertion (A): Melting of ice at needs less heat than then warming the melted water from to .
Reason (R): Since water at and ice at are at the same temperature, a given mass of each has the same internal energy.
- 611 mark
Question 61
Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.
Assertion (A): A block of ice at emits thermal radiation.
Reason (R): Only bodies that are hotter than their surroundings emit radiation.
- 621 mark
Question 62
Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.
Assertion (A): When a body is only a few kelvin warmer than its surroundings, doubling its excess temperature very nearly doubles its rate of loss of heat.
Reason (R): Newton's law of cooling holds for any temperature difference between a body and its surroundings.
- 635 marks
Question 63
A melting bullet. A lead bullet of mass at strikes a thick wooden block at and stops inside it. Assume that half of its kinetic energy becomes internal energy of the bullet, and the rest goes into the wood. For lead (Tables 10.3 and 10.5): , melting point , .

(a) Find the heat that goes into the bullet, and show that it is enough to bring the bullet to its melting point. What mass of lead melts?
(b) What is the least speed at which the whole bullet would melt, on the same assumption?
(c) For lead, compare the latent heat of fusion with the heat needed to warm from to the melting point. Use this to explain why a speed only about higher than melts the whole bullet.
(d) Why is the assumption about "half" the kinetic energy the weakest part of this calculation, and which way would your answers change if more than half stayed in the bullet?
- 645 marks
Question 64
Measuring a poor conductor. To find the thermal conductivity of a board material, a student clamps a disc of it, thick and of radius , between a steam chamber at above and a thick copper disc of the same radius below. The copper disc has mass () and loses heat to the room from its own surface. After a long time its temperature stays steady at . In a separate run, the copper disc is heated a little above on its own, with the specimen laid back on top of it, and allowed to cool: as it passes it is cooling at .

(a) Explain why, in the steady state, the rate at which heat flows through the specimen equals measured in the cooling run at .
(b) Find the rate of heat flow through the specimen.
(c) Find the thermal conductivity of the board material, and identify a material of Table 10.6 with a similar value.
(d) Explain why the specimen is made thin and wide. If the student forgot to put the specimen back on the copper disc during the cooling run, would the value of come out too large or too small?
- 655 marks
Question 65
When does Newton's law of cooling work? A solid copper sphere of radius (density , ) is coated with lamp-black so that it behaves as a black body. It is heated to and hung in an evacuated enclosure whose walls are kept at . Take .
(a) Find the net rate at which the sphere loses heat at the start.
(b) Find its initial rate of fall of temperature.
(c) For a small excess temperature , one may write , which leads to Newton's law of cooling. Use this to estimate the rate of heat loss at , and explain why the estimate fails so badly.
(d) Repeat the exact calculation and the estimate when the sphere has cooled to , and comment.
- 665 marks
Question 66
Finding absolute zero. A student uses a constant-volume gas thermometer containing a small amount of hydrogen at low density. The pressure of the gas is when the bulb is in melting ice and when it is in steam at .
(a) Find the change in pressure per degree Celsius, and by extrapolation the temperature at which the pressure of the gas would become zero.
(b) The bulb is then placed in a water bath and the pressure is . Find the temperature of the bath in and in kelvin.
(c) Sketch the graph of pressure against temperature, showing the extrapolation, and state what the intercept means.
(d) Explain why the gas must be at low density, and what you would expect if the experiment were repeated with oxygen at low density.
- 674 marks
Question 67
Reading phase diagrams. The text gives these values. Water: triple point and ; its vaporisation curve ends at , ; its fusion curve slopes towards lower temperature as the pressure rises. Carbon dioxide: triple point and ; its fusion curve slopes towards higher temperature as the pressure rises; its vaporisation curve passes through at ; at the solid sublimes at .
(a) In freeze-drying, frozen food at is placed in a chamber pumped down to well below , and gently warmed. Explain why the ice in the food disappears without ever becoming liquid water.
(b) A dish of water at is put in a sealed chamber, and the pressure above it is slowly lowered from while its temperature is held at . Using the phase diagram of water, explain what happens to the water.
(c) A large pressure is applied to a block of ice at and to a block of solid CO just below its melting point. Which one can melt under the pressure? Use this to explain why the bottom of a thick glacier can be wet even when its temperature is a little below .
(d) A CO fire extinguisher at contains liquid CO with vapour above it. Estimate the pressure inside, and explain why white "snow" forms at the nozzle when it is used.
- 683 marks
Question 68
A stuck stopper. The glass stopper of a reagent bottle is stuck in the neck, whose inner diameter is . Bottle and stopper are both made of ordinary glass (, Table 10.2). A laboratory assistant pours hot water over the outside of the neck, which warms by .
(a) By how much does the inner diameter of the neck increase, if the stopper is still at room temperature?
(b) If, by the time the assistant pulls, the stopper has also warmed by , what clearance has been gained?
(c) Explain why the hot water must be poured on the neck, and quickly, and why warming the whole bottle slowly in an oven would not help.
- 693 marks
Question 69
Same per atom? The specific heats of four metals from Table 10.3 are: aluminium , copper , silver and lead . Their molar masses are , , and respectively.
(a) Calculate the molar specific heat capacity of each metal.
(b) The specific heats differ by a factor of about , but the molar values do not. Interpret this in terms of atoms.
(c) Use your result to predict the specific heat of gold (molar mass ).
- 703 marks
Question 70
Convection in the body and in the atmosphere. (a) The text calls the human circulatory system an example of forced convection. Explain how blood carries heat from the body's core to the skin, and why this is forced rather than natural convection.
(b) Explain how unequal heating of the earth sets up the trade winds, and why the air that rises at the equator comes down at about N latitude rather than at the poles.
(c) Are these winds examples of natural or forced convection? Give a reason.
- 713 marks
Question 71
Radiation from a cup of tea. A cup holds of tea at () in a room at . The outer surface of the cup, of area , is at the temperature of the tea. Take .
(a) Find the net rate of loss of heat by radiation if the cup's surface behaves as a black body.
(b) Find the same rate if the cup is given a shiny metallic coating of emissivity .
(c) Find the rate at which the tea would cool in case (a) if radiation were the only loss. Explain why a shiny coating alone does not keep the tea hot for long.
- 723 marks
Question 72
Reading temperature gradients. Two rods A and B of equal cross-section are joined end to end, and their sides are lagged. Rod A is long and rod B is long. The free end of A is held at and the free end of B is held at a lower fixed temperature. In the steady state, the temperature falls steadily along each rod: by per cm along A and by per cm along B.

(a) Find the ratio of the thermal conductivities. Which pair of metals in Table 10.6 could A and B be?
(b) Find the temperatures of the junction and of the cold end of B.
(c) Sketch a graph of temperature against distance along the two rods.
- 733 marks
Question 73
Two thermometers, two answers. The resistance of a platinum wire varies with Celsius temperature as , with at , and . A technician builds a "platinum scale" by assuming that the resistance changes linearly with temperature, fixing it at the ice and steam points ( and on her scale).
(a) Find the resistance of the wire at the steam point.
(b) What does the platinum scale read when the true Celsius temperature is ?
(c) Explain why the two scales agree at and but disagree in between, and why this happens between any two thermometers based on different thermometric properties.
- 743 marks
Question 74
A kettle left on. An electric kettle rated contains of water at . Take and .
(a) Neglecting all heat losses and the heat taken by the kettle itself, how long does the water take to reach the boiling point?
(b) If the kettle's switch then fails, how much longer will it take, on the same assumption, to boil all the water away?
(c) In fact, in a room at , the water takes to reach the boiling point. Neglect the kettle's own heat capacity, so that the missing energy is lost to the room. Find the fraction of the heater's energy that reaches the water. Assuming the same fraction during boiling, estimate the time to boil the kettle dry, and say whether the real time is likely to be longer or shorter than this estimate.
- 752 marks
Question 75
In regions with severe winters, exposed water pipes often burst on very cold nights, even though metals contract when cooled. Explain why this happens, and why it is the water, not the metal, that matters here.
- 762 marks
Question 76
A woollen blanket keeps a person warm on a cold night, yet a block of ice wrapped in the same blanket in a warm room does not melt faster; it lasts longer. Explain both observations with one idea.
- 772 marks
Question 77
A television presenter says, "Today, at , it is twice as hot as yesterday, when it was ." Explain what is wrong with this statement. What is the true ratio of the two temperatures, and what Celsius temperature would really be "twice" ?
- 782 marks
Question 78
White clothes are preferred in hot summers, but some Arctic clothing has a thin, shiny metallic layer on the inside, next to the body. Explain how each choice reduces the unwanted heat transfer, using what you know about absorbers and emitters of radiation.
- 792 marks
Question 79
In the method of mixtures, the calorimeter is a thin vessel of copper or aluminium with a stirrer of the same metal, kept inside a wooden jacket with glass wool packed between them. Explain the purpose of each of these choices.
- 802 marks
Question 80
The heat sink fixed on a computer's processor chip is a block of aluminium or copper with many thin fins, and is often coloured black. Explain why each of these features helps to keep the chip cool.
