Confirming your payment

Skip to content

Opening your dashboard

Class 11 Physics Chapter 8 Mechanical Properties Of Solids: Practice Questions

37 questions on Chapter 8, each worked through on its own page with the AI tutor. Class 11 Physics, CBSE 2026-27.

37 questions

1–5 marks · Hard difficulty

  1. 1

    Question 1

    The shear modulus (modulus of rigidity) and the Young's modulus of copper are GG and YY respectively. A copper wire of length LL and area of cross-section AA is drawn out so that its length becomes 5L5L and its area of cross-section becomes A5\dfrac{A}{5}. Now,

    MCQHard
    1 mark
  2. 2

    Question 2

    The stress–strain graphs of three materials, drawn up to their elastic limits, are shown below.

    Class 11 Physics Mechanical Properties Of Solids

    Which of the following statements is true?

    MCQHard
    1 mark
  3. 3

    Question 3

    Which of the following cannot be the value of Poisson's ratio of a material?

    MCQHard
    1 mark
  4. 4

    Question 4

    The breaking stress of a wire depends on

    MCQHard
    1 mark
  5. 5

    Question 5

    In the stress–strain graph shown, the yield point is

    Class 11 Physics Mechanical Properties Of Solids

    MCQHard
    1 mark
  6. 6

    Question 6

    The shear modulus (modulus of rigidity) of an ideal liquid is

    MCQHard
    1 mark
  7. 7

    Question 7

    A wire is cut to half its original length. The maximum load that it can support without breaking will

    MCQHard
    1 mark
  8. 8

    Question 8

    A steel wire of diameter 2.0 mm2.0\ \text{mm} and length 2.0 m2.0\ \text{m} is stretched by 1.0 mm1.0\ \text{mm}. Its diameter decreases by 0.30 μm0.30\ \mu\text{m}. The Poisson's ratio of steel is

    MCQHard
    1 mark
  9. 9

    Question 9

    A spring is stretched by applying a load to its free end. The strain produced in the spring is

    MCQHard
    1 mark
  10. 10

    Question 10

    The graph shows how the extension of two steel wires P and Q, of the same length, changes with the load hung from them.

    Class 11 Physics Mechanical Properties Of Solids

    Which of the following statements is correct?

    MCQHard
    1 mark
  11. 11

    Question 11

    A mild steel wire of length 2L2L and area of cross-section AA is stretched, well within its elastic limit, horizontally between two pillars. A mass mm is hung from the midpoint of the wire, which then sags by xx (x≪Lx \ll L), as shown. The strain in the wire is

    Class 11 Physics Mechanical Properties Of Solids

    MCQHard
    1 mark
  12. 12

    Question 12

    A rectangular frame is to be hung symmetrically by two strings of equal length from two supports. It can be done in any of the three ways shown.

    Class 11 Physics Mechanical Properties Of Solids

    The tension in the strings will be

    MCQHard
    1 mark
  13. 13

    Question 13

    Two cylindrical rods of identical dimensions, one of rubber and the other of steel, are each fixed rigidly at one end to the roof. A mass MM is attached to the centre of the free end of each rod. Then

    MCQHard
    1 mark
  14. 14

    Question 14

    A wire of length LL and area of cross-section AA is stretched by a force FF, and its length increases by ΔL\Delta L. The Young's modulus of the material of the wire is

    MCQHard
    1 mark
  15. 15

    Question 15

    The correct relation between stress σ\sigma, strain ε\varepsilon and Young's modulus YY is

    MCQHard
    1 mark
  16. 16

    Question 16

    What is the ultimate tensile strength of a material?

    Hard
    2 marks
  17. 17

    Question 17

    Define compressibility.

    Hard
    1 mark
  18. 18

    Question 18

    Which is more elastic, water or air? Give a reason.

    Hard
    1 mark
  19. 19

    Question 19

    (a) Classify each of the following as elastic, plastic or an elastomer, and justify each answer: a steel spring, a lump of putty, a rubber band.

    (b) What is meant by an ideal plastic body?

    Hard
    2 marks
  20. 20

    Question 20

    The stress–strain graph for a metal wire is shown. Up to point B, the wire returns to its original state O along the curve BAO when it is gradually unloaded. Point E is the fracture point of the wire.

    Class 11 Physics Mechanical Properties Of Solids

    (a) Up to which point on the curve is Hooke's law obeyed?

    (b) Which point corresponds to the elastic limit (yield point) of the wire?

    (c) Indicate the elastic and plastic regions of the curve.

    (d) What happens if the wire is loaded up to the stress at point C and then gradually unloaded?

    Hard
    3 marks
  21. 21

    Question 21

    A crane is to lift loads of up to 5.0 tonnes with a steel rope. The yield strength of the steel is 2.5×108 N m−22.5\times10^{8}\ \text{N m}^{-2}, and the designer wants a safety factor of 4 on the load (take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}).

    (a) Find the minimum area of cross-section and the corresponding radius of the rope.

    (b) Why is such a rope made of many thin wires braided together rather than a single thick wire?

    Hard
    2 marks
  22. 22

    Question 22

    A silica glass rod has a diameter of 1.0 cm1.0\ \text{cm} and a length of 10 cm10\ \text{cm}. The breaking strength of glass is 50×106 N m−250\times10^{6}\ \text{N m}^{-2}. Estimate the largest mass that can be hung from the rod without breaking it. (Take g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.)

    Hard
    2 marks
  23. 23

    Question 23

    State Hooke's law. What is meant by the modulus of elasticity?

    Hard
    1 mark
  24. 24

    Question 24

    What is Young's modulus?

    Hard
    1 mark
  25. 25

    Question 25

    A steel wire of length 2.0 m2.0\ \text{m} and area of cross-section 1.0 mm21.0\ \text{mm}^{2} is stretched by 1.0 mm1.0\ \text{mm} within its elastic limit. Take Y=2.0×1011 N m−2Y = 2.0\times10^{11}\ \text{N m}^{-2} for steel.

    (a) Find the elastic potential energy stored in the wire.

    (b) Find the energy stored per unit volume.

    Hard
    2 marks
  26. 26

    Question 26

    Which is more elastic, steel or rubber? Explain.

    Hard
    1 mark
  27. 27

    Question 27

    A steel beam of length L=2.0 mL = 2.0\ \text{m}, breadth b=5.0 cmb = 5.0\ \text{cm} and depth d=10 cmd = 10\ \text{cm} rests on supports near its ends and carries a load W=5000 NW = 5000\ \text{N} at its centre. The sag at the centre is δ=WL34bd3Y\delta = \dfrac{WL^{3}}{4bd^{3}Y}; take Y=2.0×1011 N m−2Y = 2.0\times10^{11}\ \text{N m}^{-2}.

    Class 11 Physics Mechanical Properties Of Solids

    (a) Find the sag of the beam.

    (b) Find the sag if (i) the depth is doubled, (ii) the breadth is doubled instead. Which is the better way to stiffen the beam?

    Hard
    3 marks
  28. 28

    Question 28

    The stress–strain graphs of three materials are shown (× marks the fracture point).

    Class 11 Physics Mechanical Properties Of Solids

    (a) Which graph corresponds to a brittle material? Give a reason.

    (b) What kind of material does each of the other two graphs represent?

    Hard
    2 marks
  29. 29

    Question 29

    Identical springs of steel and copper are equally stretched. On which spring will more work have to be done?

    Hard
    3 marks
  30. 30

    Question 30

    What is the Young's modulus of a perfectly rigid body?

    Hard
    2 marks
  31. 31

    Question 31

    A long steel bar of cross-sectional area AA is under tension, with forces FF acting at its ends along its length. Consider a plane aa′ through the bar making an angle θ\theta with the length of the bar, as shown.

    Class 11 Physics Mechanical Properties Of Solids

    Find the tensile and shearing stresses on this plane.

    (a) For what angle is the tensile stress maximum?

    (b) For what angle is the shearing stress maximum?

    Hard
    5 marks
  32. 32

    Question 32

    (a) A steel wire of circular cross-section has a radius of 0.10 cm0.10\ \text{cm} and a length of 10 m10\ \text{m} when lying horizontal. It hangs from a hook on the wall, and a mass of 25 kg25\ \text{kg} is hung from its free end. Assuming the wire is uniform and that lateral strains are negligible compared with longitudinal strains, find the extension of the wire. (Density of steel =7860 kg m−3= 7860\ \text{kg m}^{-3}, Y=2.0×1011 N m−2Y = 2.0\times10^{11}\ \text{N m}^{-2}, g=10 m s−2g = 10\ \text{m s}^{-2}.)

    (b) If the yield strength of steel is 2.5×108 N m−22.5\times10^{8}\ \text{N m}^{-2}, what is the maximum weight that can be hung at the lower end of the wire?

    Hard
    5 marks
  33. 33

    Question 33

    A uniform steel rod of length 2l2l, area of cross-section AA and mass MM rotates with angular speed ω\omega in a horizontal plane about a vertical axis through its centre. If YY is the Young's modulus of steel, find the extension in the length of the rod.

    Hard
    5 marks
  34. 34

    Question 34

    In nature, structural members usually fail because of large torques from twisting or bending rather than from tensile or compressive strains. This kind of structural breakdown is called buckling. In tall cylindrical structures like trees, the torque is caused by the tree's own weight bending it, so that the vertical through the centre of gravity no longer falls within the base. The elastic torque produced by this bending about the central axis of the tree is Yπr44R\dfrac{Y\pi r^{4}}{4R}, where YY is the Young's modulus, rr is the radius of the trunk and RR is the radius of curvature of the bent surface (the neutral surface) along the height of the tree, which contains the centre of gravity. Estimate the critical height of a tree for a given radius of the trunk.

    Hard
    5 marks
  35. 35

    Question 35

    Explain the concept of Young's modulus. Derive an expression for the elongation of a uniform rod under a stretching force, and discuss the factors on which the elongation depends.

    Hard
    5 marks
  36. 36

    Question 36

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): Strain is the ratio of the change in a dimension of a body to its original dimension.

    Reason (R): The dimensional formula of strain is [ML−1T−2][\text{ML}^{-1}\text{T}^{-2}].

    MCQHard
    1 mark
  37. 37

    Question 37

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.

    Assertion (A): The Young's modulus of a perfectly plastic body is zero.

    Reason (R): A perfectly plastic body does not regain its original shape at all when the deforming force is removed.

    MCQHard
    1 mark