Opening your dashboard
Class 7 Science Chapter 3: Electricity: Circuits & Components Question Answers
11 textbook questions with step-by-step answers, free to read, for CBSE 2026-27.
Get talked through Ch 3, not just shown the answer
Reading a finished solution is not the same as being able to do it. The AI tutor takes one question at a time and works it with you, in your own words, until you can.
- Ask it out loud, in your own words
- It gives you the next step, not the answer
- Stuck on part (ii)? Start there
11 questions with solutions
1–3 marks · Mixed difficulty
- 11 mark
Question 1
Choose the incorrect statement.
(i) A switch is the source of electric current in a circuit.
(ii) A switch helps to complete or break the circuit.
(iii) A switch helps us to use electricity as per our requirement.
(iv) When the switch is in ‘OFF’ position, there is an air gap between its terminals.
Solve with AIWritten solution
Statement (i) is incorrect.
A switch is not a source of electric current. In a circuit, the electric cell (or battery) is the source of electrical energy. A switch is a simple device that either completes or breaks a circuit.
The other statements are correct:
- (ii) In the ‘ON’ position the switch completes the circuit and current flows; in the ‘OFF’ position it breaks the circuit.
- (iii) Because a switch lets us turn the current on and off, we can use a torch, a fan or a light only when we need it.
- (iv) In the ‘OFF’ position there is a gap filled with air between the terminals of the switch, so current cannot flow, just as in the home-made switch the safety pin does not touch the second drawing pin.
- 21 mark
Question 2
Observe Fig. 3.16. With which material connected between the ends A and B, the lamp will not glow?
Solve with AIWritten solution
The lamp will not glow if an insulator is connected between A and B, for example a plastic scale, a rubber eraser, a wooden stick or a piece of ceramic.
The lamp glows only when the circuit is complete and current passes through it. Electric current cannot pass through insulators, so the gap between A and B stays open and no current flows.
If a conductor, such as a metal key, a coin, a safety pin or aluminium foil, is connected between A and B, current flows and the lamp glows.
- 32 marks
Question 3
In Fig. 3.17, if the filament of one of the lamps is broken, will the other glow? Justify your answer.
Solve with AIWritten solution
No, the other lamp will not glow.
In Fig. 3.17 the battery and the two lamps are joined one after another in a single loop, so there is only one path for the current. To go round the circuit, the current must pass through the filament of both lamps.
A broken filament makes a gap in this path (the lamp has ‘fused’). The circuit is no longer complete, so no current flows anywhere in it, and the second lamp also stays off even though it is not damaged.
- 42 marks
Question 4
A student forgot to remove the insulator covering from the connecting wires while making a circuit. If the lamp and the cell are working properly, will the lamp glow?
Solve with AIWritten solution
No, the lamp will not glow.
The covering on connecting wires is made of plastic or rubber, which are insulators: electric current cannot pass through them. If the covering is not removed from the ends, the metal of the wire never touches the terminals of the cell or the lamp. The path is broken at the joints, the circuit is not complete, and no current flows, even though the lamp and the cell are working.
That is why about 1 cm of the plastic covering is removed from both ends of each wire, to expose the metal, before making a circuit.
- 52 marks
Question 5
Draw a circuit diagram for a simple torch using symbols for electric components.
Solve with AIWritten solution
A torch has a battery of two cells, a switch and a lamp, all joined in one loop. Its circuit diagram is shown below.

- Battery: two cell symbols joined, the positive terminal (long line) of one cell to the negative terminal (short line) of the next.
- Lamp: a circle with a cross inside.
- Switch: drawn here in the ‘OFF’ position. When the torch is switched on, the switch closes the gap, the circuit is complete, and current flows from the positive terminal of the battery through the lamp back to the negative terminal, so the lamp glows.
A torch with an LED lamp has the same diagram with the LED symbol in place of the lamp, connected so that its triangle points in the direction of the current, from the positive terminal side of the battery.
- 62 marks
Question 6
In Fig. 3.18:
(i) If is in ‘ON’ position, is in ‘OFF’ position, which lamp(s) will glow?
(ii) If is in ‘OFF’ position, is in ‘ON’ position, which lamp(s) will glow?
(iii) If and both are in ‘ON’ position, which lamp(s) will glow?
(iv) If both and are in ‘OFF’ position, which lamp(s) will glow?
Solve with AIWritten solution
Go round the circuit in Fig. 3.18 starting from the battery: battery, lamp , switch , lamp , switch , and back to the battery. All of them lie on one single path, so current can flow only when this path is complete, that is, only when both switches are ‘ON’.
(i) Neither lamp glows. is ‘OFF’, so there is a gap in the only path and no current flows through or .
(ii) Neither lamp glows. Now is ‘OFF’ and breaks the path.
(iii) Both lamps, and , glow. Both switches close their gaps, the circuit is complete and current passes through both lamps.
(iv) Neither lamp glows. The path is broken at two places.
- 73 marks
Question 7
Vidyut has made the circuit as shown in Fig. 3.19. Even after closing the circuit, the lamp does not glow. What can be the possible reasons? List as many possible reasons as you can for this faulty operation. What will you do to find out why the lamp did not glow?
Solve with AIWritten solution
Possible reasons
- The switch is not really closed. In Fig. 3.19 the safety pin is not touching the second drawing pin. If the safety pin does not press on both drawing pins, a gap remains and the circuit stays open.
- The cell is used up. A cell that can no longer give electrical energy cannot make current flow.
- The lamp is fused. Its filament may be broken, so current cannot pass through the lamp.
- A loose connection. A wire end may not be touching the cell terminal, a screw of the lamp holder or a drawing pin, or the lamp may be loose in its holder.
- Covering not removed. The plastic covering at a wire end may not have been removed, so only an insulator touches the terminal.
- A broken wire. The metal inside a wire may be broken even though its plastic covering looks fine.
- Rust or dirt on the drawing pins, the safety pin or the cell terminals may stop the metal parts from touching properly.
How to find the fault
Check one part at a time, changing only that part and keeping the rest of the circuit the same:
- Press the safety pin firmly onto the second drawing pin. If the lamp now glows, the switch was the problem.
- Check every joint: tighten loose ends, make sure the bare metal of each wire touches its terminal, and push the lamp firmly into its holder.
- Take the switch out and touch its two wires directly together. If the lamp glows now, the switch is faulty.
- Put a new cell, or one that works in another circuit, in place of the old cell. If the lamp now glows, the old cell was used up.
- Put a lamp that glows in another circuit in place of the old lamp, or look at its filament. If the new lamp glows, the old one was fused.
- Test each wire with a working conduction tester (a cell, a lamp and wires). If the tester lamp does not glow through a wire, that wire is broken.
The first change that makes the lamp glow shows the fault.
- 82 marks
Question 8
In Fig. 3.20, in which case(s) the lamp/LED will not glow when the switch is closed?
Solve with AIWritten solution
Only in case (c) will the LED not glow. In (a), (b) and (d) the lamp or LED glows.
In a cell symbol the long line is the positive terminal and the short line is the negative terminal. Current flows from the positive terminal round the circuit to the negative terminal. In the LED symbol the triangle points in the direction in which current can flow.
(a) and (b) When the switch is closed the circuit is complete, so the lamp glows. The cell is turned the other way round in (b), but with an incandescent lamp it does not matter which of its terminals connects to the positive terminal of the cell, so the lamp glows in both.
(c) The long line of the battery is on its right. Current leaves the positive terminal towards the right, passes through the switch, goes up the right side and reaches the LED from the side of the bar. The triangle points to the right, the opposite way, so current cannot pass through the LED. The negative terminal of the LED is joined to the positive side of the battery, and the LED does not glow.
(d) The battery is turned round: its long line is on the left. Current goes up the left side and enters the LED from the triangle side, in the direction the triangle points. The positive terminal of the LED is joined to the positive side of the battery, so the LED glows.
- 92 marks
Question 9
Suppose the ‘+’ and ‘–’ symbols cannot be read on a battery. Suggest a method to identify the two terminals of this battery.
Solve with AIWritten solution
Use an LED, because current can pass through an LED in one direction only.
- Connect the longer wire (positive terminal) of the LED to one terminal of the battery, and the shorter wire (negative terminal) to the other terminal.
- If the LED glows, the terminal joined to the longer wire is the positive (+) terminal, and the other one is the negative (–) terminal.
- If the LED does not glow, interchange the two wires. Now the LED glows, and the terminal joined to the longer wire this time is the positive terminal.
An incandescent lamp cannot be used for this test, because it glows whichever way its terminals are connected to the battery.
The shape of the terminals also helps: on an electric cell the terminal with the small protruding metal cap is positive and the one with the flat metal disc is negative.
- 103 marks
Question 10
You are given six cells marked A, B, C, D, E, and F. Some of these are working and some are not. Design an activity to identify which of them are working.
(i) List the items that you require.
(ii) Write the procedure that you will follow.
(iii) With the items, carry out the activity to identify the cells that are working.
Solve with AIWritten solution
(i) Items required:
- the six cells A, B, C, D, E and F
- one torch lamp (incandescent lamp) fixed in a lamp holder
- a cell holder for one cell
- two connecting wires with about 1 cm of plastic covering removed from both ends
- one cell that is known to be working, to check the lamp and wires first
(ii) Procedure:
- Connect the known working cell to the lamp with the two wires. If the lamp glows, the lamp and wires are fine.
- Take that cell out and put cell A in the holder. Make sure the bare ends of the wires touch its two terminals.
- Observe whether the lamp glows and record Yes or No in a table.
- Repeat with cells B, C, D, E and F one by one, using the same lamp and the same wires each time, so that only the cell changes.
- If the lamp does not glow with a cell, check all the connections once more before deciding.
(iii) Carry out the activity and record the observations in a table like this:
Cell Lamp glows (Yes/No) Working or not working A B C D E F Every cell with which the lamp glows is working; every cell with which the lamp does not glow, even with good connections, is not working. For example, if the lamp glows only with A, C and F, then cells A, C and F are working and cells B, D and E are not.
- 113 marks
Question 11
Using an LED that requires two cells in series to glow, Tanya made the circuit as shown in Fig. 3.21. Will the lamp glow? If not, draw the wires for correct connections.
Solve with AIWritten solution
No, the LED (lamp) will not glow.
Look at the terminals in Fig. 3.21:
- The black wire joins the negative terminal of the upper cell to the negative terminal of the lower cell. To make a battery, the positive terminal of one cell must be connected to the negative terminal of the next cell, so these two cells do not form a battery.
- Both wires going to the LED come from positive terminals: the green wire joins the positive terminal of the upper cell to the shorter wire (negative terminal) of the LED, and the yellow wire joins the positive terminal of the lower cell to the longer wire (positive terminal) of the LED. The negative terminal of the LED is not connected to a negative terminal.
An LED lights up only when its positive terminal is connected to the positive terminal of the battery and its negative terminal to the negative terminal of the battery, so it does not glow here.
Correct connections (keep the cells where they are; remove the black and green wires):
- Wire 1: join the positive terminal of the upper cell to the negative terminal of the lower cell. The two cells now make a battery.
- Wire 2 (the yellow wire, kept): positive terminal of the lower cell, which is now the positive terminal of the battery, to the longer wire of the LED.
- Wire 3: negative terminal of the upper cell, which is now the negative terminal of the battery, to the shorter wire of the LED.

Now current flows from the positive terminal of the battery into the longer wire of the LED, through the LED, out of its shorter wire and back to the negative terminal of the battery, so the LED glows. Turning the upper cell around and keeping the black, green and yellow wires as they are also works.
What Class 7 Science Ch 3 covers
The sections of the chapter, in the order the book takes them. Every question above comes from one of these.
- 01Everyday Uses of Electricity
- 02Components of an Electric Circuit
- 03Circuit Diagrams
- 04Electrical Conductors and Insulators
More ways to study this chapter
The same chapter asked three other ways. Practise it, revise it, and see what the board has set on Ch 3 before.
Class 7 Science Ch 3 questions students ask
How many questions are there in Class 7 Science Ch 3?
11 questions. Every one is solved step by step on this page.
Are these Class 7 Science question answers free?
Yes. Every question and its full working is free to read, with no account needed.
Can I download the Class 7 Science Ch 3 solutions as a PDF?
There is no PDF to download. Every solution is on this page instead, which means it is searchable, always the current syllabus, and readable on a phone. Use your browser's print option if you want it on paper.
