Opening your dashboard
Class 7 Science Chapter 3 Electricity: Circuits & Components: Competency-Based Questions (CBQ)
40 questions on Chapter 3, each worked through on its own page with the AI tutor. Class 7 Science, CBSE 2026-27.
40 questions
1–4 marks · Mixed difficulty
- 11 mark
Question 1
Nihal's group is sorting the uses of electricity for their project chart under these headings: Cooking, Lighting, Transportation, Heating and Cooling, Entertainment, Communication and Others. Nihal adds his grandmother's electric blanket, which she switches on to keep her bed warm on winter nights in Shimla. Ruchi wants to put it under Cooking because "it gets hot, just like a toaster".
Under which heading should the electric blanket go, and which device already on the chart belongs with it?
- 21 mark
Question 2
Jatin's science kit has a torch lamp, a cell and two wires, but the lamp holder is missing. His teacher tells him to fix the bare ends of the wires to the lamp with electrical tape. The figure shows the lamp with four points marked P, Q, R and S.

To which two points must Jatin tape the wires so that the lamp glows when the other ends of the wires are joined to the cell?
- 31 mark
Question 3
Arnav joins a cell to a lamp in a holder using two wires, X and Y, as shown. The lamp glows. He wants to draw arrows on the wires to show which way the electric current goes.

Which statement about the current in Arnav's circuit is correct?
- 41 mark
Question 4
The plastic top of Dadaji's plug has cracked, so he goes to buy a new plug. The shopkeeper shows him plugs in which the two parts marked in the figure, X (the pins) and Y (the plug top), are made of different materials.

Which plug should Dadaji buy?
- 51 mark
Question 5
Tanvi makes a conduction tester from a cell, a lamp and wires. When she touches its two free ends together, the lamp glows. She then tests some things from her school bag and records her results.
Object Made of Lamp glows? Safety pin Steel Yes Marble Glass No Divider Steel Yes Eraser Rubber No Ruler Wood No Paper clip Iron Yes Which conclusion is supported by every row of Tanvi's table?
- 61 mark
Question 6
Kriti builds the circuit shown below for her model of a night lamp. Her holder has two cells, and the end marked + is the positive terminal of the battery. The safety pin of her switch touches both drawing pins. The longer leg of her LED is joined, through the switch, to the + terminal of the battery.

Which circuit diagram correctly shows Kriti's circuit?

- 71 mark
Question 7
Dev opens his two-cell holder and looks inside. Each cell's flat disc end presses against a spring, and a metal strip at the bottom of the holder joins the two slots. The two grey wires, P and Q, have no + or – marks.

Which wire is the positive terminal of Dev's battery?
- 81 mark
Question 8
Meena goes with her grandfather to an electrical shop in Lucknow. He needs cells for three things: his hearing aid, which is tiny and fits behind his ear; the wall clock in the kitchen; and a spare for his mobile phone, which he charges every night. The shopkeeper shows them button cells, cylindrical cells and rechargeable batteries.
Which choice matches each device with the right kind of cell?
- 91 mark
Question 9
Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.
Assertion (A): Anu's LED torch stops glowing. The repair-shop owner tells her that, whatever the fault is, it cannot be a broken filament, as it might be in an old torch.
Reason (R): LEDs do not have filaments.
- 101 mark
Question 10
Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.
Assertion (A): The copper wires that the electrician fits in Aarav's new house are covered with plastic or rubber.
Reason (R): Plastic and rubber are good conductors of electricity.
- 112 marks
Question 11
Aditi's old torch has an incandescent lamp, and it does not glow. She checks it step by step:
- She takes out the lamp and joins it to a fresh cell with two wires. It does not glow. She swaps the two wires at the cell, and it still does not glow.
- She puts her torch's cells into her friend's torch, which has a good lamp. Her friend's torch glows.
(i) Which part of Aditi's torch is faulty? Use her checks to explain.
(ii) What has most likely happened inside that part, and why does this stop it from glowing?
- 122 marks
Question 12
Pallavi draws this circuit diagram for her model of a porch light.

(i) Will the lamp glow as the diagram is drawn? Give a reason.
(ii) When she turns the switch ON, from which end of the battery, X or Y, does the current leave? How can you tell from the symbol?
- 132 marks
Question 13
Electrician Mohan has come to fix a loose switch in Shreya's home. Shreya notices that he wears thick rubber gloves, stands on a dry wooden plank and uses a screwdriver with a plastic handle.

(i) How do the rubber gloves, the wooden plank and the plastic handle protect Mohan?
(ii) Why would Mohan be in danger if he worked on the switchboard with bare, wet hands?
- 142 marks
Question 14
Hari has made a small night light: two cells joined to make a battery, then a switch that is ON, then an LED that glows, all in one loop. He wants to send the plan to his pen-friend Lucas in France, who cannot read Hindi or English well.
(i) Why is a circuit diagram a better way to send this plan than a description in words?
(ii) Draw the circuit diagram of Hari's night light.
- 153 marks
Question 15
Asha is making a switch for her science-fair model of a lighthouse. On her table she has two drawing pins, a stiff strip of folded aluminium foil, a wooden ice-cream stick, a piece of cardboard and some wires.
(i) Which should she use as the moving part of the switch: the foil strip or the ice-cream stick? Why?
(ii) Describe the ON and OFF positions of her switch, and what happens in the circuit in each.
(iii) Asha's brother says the switch will work only if it is placed right next to the cell. Is he right? Explain.
- 163 marks
Question 16
For the science fair, Joseph makes a quiz board. On the front of a cardboard sheet he writes three questions, Q1 to Q3, on the left, and their answers, A1 to A3, on the right in a jumbled order, each next to a metal paper fastener. At the back, plastic-covered wires join each question's fastener to the fastener of its correct answer, as shown. A player touches one free wire of a tester (a cell, a lamp and two free wires) to a question fastener and the other free wire to an answer fastener.

(i) A player touches Q2 and A1. Will the lamp glow? Explain.
(ii) The wires at the back cross each other. Why must they be plastic-covered?
(iii) As a prank, a friend removes the wire behind Q3 and puts a rubber band, stretched between the same two fasteners, in its place. What will a player see on touching Q3 and its correct answer, and why?
- 173 marks
Question 17
The instruction booklet of Riya's toy police car shows this circuit diagram for its headlight.

(i) How many cells does the toy need? How can you tell from the diagram?
(ii) Which end of the battery, E or F, is its positive terminal? Give a reason.
(iii) Riya has the right number of cells. Describe how she must place them one after another in the toy's cell compartment.
- 184 marks
Question 18
A storm hits Patna one evening, and the power goes off in Kabir's home. The ceiling fan, the refrigerator and the television stop at once. But his sister Zoya's torch still lights up the room, the wall clock keeps ticking, and their mother's mobile phone, charged in the afternoon, still works. Outside, a wire from an electric pole has fallen on the wet lane, and their father warns everyone to stay away from it. Kabir decides to build a small reading light from his science kit, which has a holder with two cells, a switch, a lamp in a holder and some wires.

(i) What do the torch, the wall clock and the mobile phone have in common that keeps them working during the power cut?
(ii) Using what you have learnt in this chapter, explain why nobody should touch the fallen wire.
(iii) Draw the circuit diagram of Kabir's reading light with the switch ON, and state the job of each part.
- 194 marks
Question 19
Class 7 students in Nashik are making a model of an extension board for their school exhibition. The model will never be plugged in. Before choosing materials, they test samples with a conduction tester and write down a note from the shopkeeper about each one.
Material Lamp glows? Shopkeeper's note Copper wire Yes Cheap, easily available Silver wire Yes Very costly, hard to get Aluminium foil Yes Cheap Plastic sheet No Cheap Ceramic tile No Cheap Rubber sheet No Cheap (i) Which materials in the table are conductors of electricity?
(ii) Which material would you choose for the outer cover of the board? Give a reason.
(iii) On a second try with the rubber sheet, Om's tester lamp glowed. He had laid both bare tester wire ends on the sheet so that they crossed over each other. Explain why the lamp glowed, and describe how he should repeat the test.
- 204 marks
Question 20
Grandpa's old torch has stopped working, so Simran opens it with him on the verandah to clean it. The figure shows what they see inside the torch, with four parts marked P, Q, R and S. Grandpa slides part Q back and forth to show her how it moves. Simran notices that the caps of both cells point towards the front of the torch, where the lamp is.

(i) Which part is the source of electrical energy in the torch?
(ii) What does part Q do to the circuit when it is slid forward to the ON position?
(iii) Trace the complete path of the current when the torch is ON, starting from the positive terminal of the cells.
- 211 mark
Question 21
On the school trip to the Bhakra Nangal Dam, Nihal's friend Gurpreet watches the water rushing out of the dam and says: "All the electricity in India is made at dams like this one, and it travels to our homes through the air."

Which statement corrects both of Gurpreet's mistakes?
- 221 mark
Question 22
Rohan puts two cells into a holder whose two slots are in a line, with a spring on the left of each slot. He joins an LED to the ends of the holder as shown, with the LED's longer leg on the wire from the right end. The LED does not glow, although the cells, the LED and the wires are all in good condition.

What should Rohan do to make the LED glow?
- 231 mark
Question 23
Ravi draws this circuit diagram for a model traffic signal. It has a battery, a switch, a lamp and an LED, all in one loop.

What will Ravi see when he builds this circuit exactly as drawn?
- 241 mark
Question 24
Gita sticks a strip of aluminium foil along the whole length of one face of a cardboard strip. She checks her conduction tester by touching its two free ends together, and its lamp glows. Then she does two tests, as shown.

In Test 1 the lamp glows. In Test 2 it does not glow. After Test 2 she touches the tester's free ends together again, and the lamp glows. Which conclusion is correct?
- 251 mark
Question 25
Rohit's torch uses two cells; his uncle's torch uses four cells, all joined + to –. Two friends talk about the four-cell torch.
Priya: "Connecting more cells provides energy to the circuit for a longer time and/or more energy."
Ankit: "So a torch with four cells will always glow for exactly twice as long as a torch with two cells."
Which statement correctly judges the two claims?
- 261 mark
Question 26
Lata has two torches that each use two cells. Torch 1 has an incandescent lamp and torch 2 has an LED lamp, and both work. Her little brother takes the cells out of both torches and puts them back with both cells turned round. In each torch the cap of one cell still touches the disc of the other, and the end cells still touch the torch's contacts.
What happens when Lata switches each torch ON?
- 271 mark
Question 27
Meher writes this description of her model: "a battery of two cells, a switch that is kept OFF, and an LED that will glow as soon as the switch is turned ON". Four friends draw circuit diagrams for it.

Which diagram matches Meher's description exactly?
- 281 mark
Question 28
Four groups in Class 7 each make a conduction tester and test the same four objects. Their records are given below.
Object Group 1 Group 2 Group 3 Group 4 Iron key Yes Yes No Yes Rubber eraser No No No No Steel coin Yes Yes No Yes Plastic scale No No No No The teacher says that one group's tester is not working. Which group is it, and what should that group check first?
- 291 mark
Question 29
Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.
Assertion (A): The lamp of Uma's torch glows only when its switch is slid to the ON position.
Reason (R): In Uma's torch, the positive terminal of one cell touches the negative terminal of the next cell.
- 301 mark
Question 30
Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R). Read the statements carefully and choose the option that correctly describes statements A and R.
Assertion (A): A copper wire from which the plastic covering has been removed cannot carry electric current.
Reason (R): Metals are conductors of electricity.
- 312 marks
Question 31
Neel builds the circuit in the picture for his model night lamp. The + terminal of his two-cell holder is marked.

(i) Draw the circuit diagram of Neel's circuit exactly as he has built it.
(ii) Neel wants the LED to glow. State the two changes he must make, and draw the circuit diagram of the circuit after the changes.
- 322 marks
Question 32
The Class 7 students of a school in Pune go on a two-day camp in a forest where there is no electric supply line. Their packing list has a torch, an electric kettle, an alarm clock that runs on a cell, a mixer grinder, a fully charged mobile phone and a radio that runs on cells.
(i) Which of these can they actually use at the camp? Explain why.
(ii) Raju suggests carrying his uncle's portable generator so that the class can do their circuit experiments at the camp with it. Is this a good idea? Give the reason the chapter gives.
- 332 marks
Question 33
With her father's help, Neha opens a broken light switch that has been taken off the wall. Inside she finds a plastic cover, two brass screws that hold the wires, and two metal contact strips that touch each other when the switch is ON.
(i) Which of these parts are conductors and which are insulators? Explain why each must be made that way.
(ii) A switch on another wall of her home has a cracked cover, and a metal strip can be seen through the crack. Why must it be repaired before anyone uses it?
- 342 marks
Question 34
The cell compartment of Aryan's toy robot holds three cells side by side. The figure shows the empty compartment. Each slot has a spring at one end. Wire A leaves from the top of slot 1 and wire B from the bottom of slot 3. The two metal strips that join the slots have come loose, and Aryan must fit them back.

(i) Show how the three cells must be placed and where the two metal strips must go, so that the three cells form one battery.
(ii) Which wire, A or B, will then be the positive terminal of the battery? Explain.
- 353 marks
Question 35
Mehul's LED has had both its legs trimmed to the same length, and its packet is lost. He has a two-cell battery with clearly marked + and – terminals, and two wires.
(i) Plan a simple test to find out which leg of the LED is the positive terminal.
(ii) In your test, how will Mehul know which leg is positive? Explain.
(iii) Mehul also has two incandescent torch lamps that look alike, but one of them has fused. How can he find the fused one with the same battery, and why does he not need to worry about which way round he joins these lamps?
- 363 marks
Question 36
During a monsoon week, the Class 7 students of a school in Mumbai each do a safety check at home. They report what they saw:
- (a) Chhaya comes out of her bath with wet hair and wet hands and presses the geyser switch.
- (b) The cord of an electric iron has a crack in its plastic covering, and the metal wire inside can be seen.
- (c) A phone charger is kept plugged in on a wet bathroom shelf.
- (d) Didi, with dry hands, switches off the fan before going out.

(i) Which of the situations (a) to (d) are unsafe?
(ii) For (b), explain the danger using what you know about conductors and insulators.
(iii) For (a) and (c), explain the danger using what the chapter says about our body.
- 373 marks
Question 37
Kiran looks at the circuit below and says: "The lamp uses up the current. So wire 2, from the lamp back to the cell, carries no current at all. We could cut it to save wire."

(i) Predict what will happen to the lamp if wire 2 is cut.
(ii) Use your prediction to evaluate Kiran's claim.
(iii) Copy the diagram and mark the direction of the current in wire 1 and in wire 2 with arrows.
- 384 marks
Question 38
Ishita's group gets three small lamps, X, Y and Z, each wrapped in paper so that only its two wires stick out. On every lamp the wires are labelled P and Q. The group joins each lamp to a two-cell battery, first with wire P on the + terminal and then with wire Q on the + terminal. Their teacher says that at least one of the lamps is an LED. The group's record is shown below.
Lamp P on the + terminal Q on the + terminal X Glows Glows Y Glows Does not glow Z Does not glow Does not glow (i) Which lamp is an LED? How do you know?
(ii) When the paper is removed, which of Y's two wires will be the longer one?
(iii) Ishita's friend says that Z is "just an LED joined the wrong way". Evaluate this claim using the table. What could Z be, and how could the group check?
- 394 marks
Question 39
Imran uses a conduction tester to find out where current can pass in objects made of more than one material. Each time, he touches the two tester wires to two points on the object. His plug has its top opened and no cord attached. His record:
Object Where the two tester wires touch Lamp glows? Screwdriver metal tip and metal shaft Yes Screwdriver metal tip and the end of the plastic handle No House wire the two cut ends of the copper Yes House wire two points on the plastic covering No Plug one pin and the other pin No Plug one pin and the screw joined to that pin inside Yes (i) Explain the two results for the house wire.
(ii) For the plug, why is the result "No" from pin to pin, but "Yes" from a pin to its own screw?
(iii) Use the screwdriver and plug results to explain how such objects are designed to protect the person using them.
- 404 marks
Question 40
Farah designs a night lamp with two cells, a switch and an LED. She writes: "Cell N, the cell next to the switch, is drawn the right way round. I will keep the switch OFF until bedtime, and the LED should glow when I turn the switch ON." She shows her circuit diagram to her teacher, who finds three mistakes in it.

(i) What is wrong with the way cells M and N are drawn, and what would happen if she joined the real cells that way?
(ii) What is wrong with the LED symbol, and how would the LED behave?
(iii) Redraw her circuit diagram correctly, as she described it, and mark with arrows the direction the current will take after she turns the switch ON.
