Confirming your payment

Skip to content

Opening your dashboard

Class 10 Science Chapter 11: Electricity Question Answers

Chapter 11 of the Class 10 Science book, filed here under Physics. 18 textbook questions with step-by-step answers, free to read, for CBSE 2026-27.

AI Tutor

Get talked through Ch 11, not just shown the answer

Reading a finished solution is not the same as being able to do it. The AI tutor takes one question at a time and works it with you, in your own words, until you can.

  • Ask it out loud, in your own words
  • It gives you the next step, not the answer
  • Stuck on part (ii)? Start there
Ch 11 question answers

18 questions with solutions

1–5 marks · Mixed difficulty

  1. 1

    Question 1

    A piece of wire of resistance RR is cut into five equal parts. These parts are then connected in parallel. If the equivalent resistance of this combination is R′R', then the ratio R/R′R/R' is –

    MCQMedium
    1 mark
    Solve with AI
    Answer
    • (A) 1/25

    • (B) 1/5

    • (C) 5

    • (D) 25

      Correct

    Option (D) is correct.

    Class 10 Physics Electricity

    If the wire is cut into five equal parts, the resistance of each part is R5\frac{R}{5}.

    All the five parts are connected in parallel. Hence, equivalent resistance (R′R') is given as:

    1R′=5R+5R+5R+5R+5R=25R\frac{1}{R'} = \frac{5}{R} + \frac{5}{R} + \frac{5}{R} + \frac{5}{R} + \frac{5}{R} = \frac{25}{R} RR′=25\frac{R}{R'} = 25

    Therefore, the ratio RR′\frac{R}{R'} is 25.

  2. 2

    Question 2

    Which of the following terms does not represent electrical power in a circuit?

    MCQMedium
    1 mark
    Solve with AI
    Answer
    • (A) I2RI^2R

    • (B) IR2IR^2

      Correct
    • (C) VIVI

    • (D) V2/RV^2 / R

    Option (B) is correct.

    Explanation: Electrical power is P=VIP = VI. Using Ohm's law, V=IRV = IR:

    P=VI=(IR) I=I2RP = VI = (IR)\,I = I^2R

    Putting I=VRI = \dfrac{V}{R} instead:

    P=V×VR=V2RP = V \times \frac{V}{R} = \frac{V^2}{R}

    So VIVI, I2RI^2R and V2R\dfrac{V^2}{R} all represent power. IR2IR^2 cannot be obtained from P=VIP = VI: its unit is A Ω2=V Ω\text{A}\,\Omega^2 = \text{V}\,\Omega, which is not the watt. So IR2IR^2 does not represent electrical power.

  3. 3

    Question 3

    An electric bulb is rated 220 V and 100 W. When it is operated on 110 V, the power consumed will be

    MCQMedium
    1 mark
    Solve with AI
    Answer
    • (A) 100 W

    • (B) 75 W

    • (C) 50 W

    • (D) 25 W

      Correct

    Option (D) is correct.

    Class 10 Physics Electricity

    Power consumed by an appliance is given by the expression,

    P=VI=V2RP = VI = \frac{V^2}{R}

    The resistance of the bulb remains constant if the supply voltage is reduced to 110 V. So, resistance should be found first.

    ⇒R=V2P\Rightarrow R = \frac{V^2}{P}

    Given P=100 WP = 100 \, \text{W};
    V=220 VV = 220 \, \text{V};

    ⇒R=(220)2100=484 Ω\Rightarrow R = \frac{(220)^2}{100} = 484 \, \Omega

    Now if the bulb is operated on 110 V, then the power consumed by it is

    P′=(V′)2R=(110)2484=25 WP' = \frac{(V')^2}{R} = \frac{(110)^2}{484} = 25 \, \text{W}
  4. 4

    Question 4

    Two conducting wires of the same material and of equal lengths and equal diameters are first connected in series and then parallel in a circuit across the same potential difference. The ratio of heat produced in series and parallel combinations would be

    MCQMedium
    1 mark
    Solve with AI
    Answer
    • (A) 1:2

    • (B) 2:1

    • (C) 1:4

      Correct
    • (D) 4:1

    Option (C) is correct.

    Class 10 Physics Electricity

    Let resistance of each wire = RR

    Series combination: Rs=R+R=2RR_s = R + R = 2R

    Parallel combination: 1Rp=1R+1R=2R  ⟹  Rp=R2\dfrac{1}{R_p} = \dfrac{1}{R} + \dfrac{1}{R} = \dfrac{2}{R} \implies R_p = \dfrac{R}{2}

    Heat produced: H=V2tRH = \dfrac{V^2 t}{R}

    (Same VV and tt for both combinations)

    HsHp=RpRs=R/22R=14\frac{H_s}{H_p} = \frac{R_p}{R_s} = \frac{R/2}{2R} = \frac{1}{4}

    Therefore, ratio of heat produced in series to parallel = 1:41:4

  5. 5

    Question 5

    How is a voltmeter connected in the circuit to measure the potential difference between two points?

    Easy
    1 mark
    Solve with AI
    Written solution

    To measure the voltage between any two points in a circuit, the voltmeter must be connected in parallel across those two points. This configuration ensures that the voltmeter accurately measures the potential difference without significantly altering the current flow in the circuit. By connecting the voltmeter in parallel, it effectively measures the voltage drop across the components between the two points, providing an accurate reading of the electrical potential difference.

    Class 10 Physics Electricity

  6. 6

    Question 6

    A copper wire has diameter 0.5 mm and resistivity of 1.6×10−8Ω1.6 \times 10^{-8} \Omega m. What will be the length of this wire to make its resistance 10 Ω? How much does the resistance change if the diameter is doubled?

    Hard
    3 marks
    Solve with AI
    Written solution

    Given: d=0.5 mm=0.0005 md = 0.5\ \text{mm} = 0.0005\ \text{m}, ρ=1.6×10−8 Ωm\rho = 1.6\times10^{-8}\ \Omega\text{m}, R=10 ΩR = 10\ \Omega

    Area of cross-section:

    A=π(d2)2=π×(0.00025)2=1.963×10−7 m2A = \pi\left(\dfrac{d}{2}\right)^2 = \pi\times(0.00025)^2 = 1.963\times10^{-7}\ \text{m}^2

    Finding length using R=ρlAR = \dfrac{\rho l}{A}:

    l=R×Aρ=10×1.963×10−71.6×10−8=122.7 ml = \dfrac{R \times A}{\rho} = \dfrac{10\times1.963\times10^{-7}}{1.6\times10^{-8}} = 122.7\ \text{m}

    When diameter is doubled (d′=1 mm=0.001 md' = 1\ \text{mm} = 0.001\ \text{m}):

    New area A′=4AA' = 4A (area increases 4 times)

    New resistance:

    R′=ρlA′=ρl4A=R4=104=2.5 ΩR' = \dfrac{\rho l}{A'} = \dfrac{\rho l}{4A} = \dfrac{R}{4} = \dfrac{10}{4} = 2.5\ \Omega

    The resistance falls from 10 Ω10\ \Omega to 2.5 Ω2.5\ \Omega when the diameter is doubled, a decrease of 7.5 Ω7.5\ \Omega: it becomes one quarter of its original value.

    Class 10 Physics Electricity

  7. 7

    Question 7

    The values of current II flowing in a given resistor for the corresponding values of potential difference VV across the resistor are given below –

    II (amperes)0.51.02.03.04.0
    VV (volts)1.63.46.710.213.2

    Plot a graph between VV and II and calculate the resistance of that resistor.

    Hard
    3 marks
    Solve with AI
    Written solution

    The plot that shows the relationship between voltage and current for a resistor is known as the I-V characteristic. In this graph, current (I) is plotted on the y-axis, and voltage (V) is plotted on the x-axis. The graph typically illustrates how the current through the resistor changes as the voltage across it is varied. Class 10 Physics Electricity

    The slope of the line gives the value of resistance (RR) as,

    Slope=1R=BCAC=26.8\text{Slope} = \frac{1}{R} = \frac{BC}{AC} = \frac{2}{6.8} ⇒R=6.82=3.4 Ω\Rightarrow R = \frac{6.8}{2} = 3.4 \, \Omega

    Therefore, the resistance of the resistor is 3.4 Ω\Omega.

  8. 8

    Question 8

    When a 12 V battery is connected across an unknown resistor, there is a current of
    2.5 mA in the circuit. Find the value of the resistance of the resistor.

    Medium
    2 marks
    Solve with AI
    Written solution

    Class 10 Physics Electricity

    Resistance (RR) of a resistor is given by Ohm's law as,

    V=IR⇒R=VIV = IR \quad \Rightarrow \quad R = \frac{V}{I}

    Where,
    Potential difference, V=12 VV = 12 \, \text{V}
    Current in the circuit, I=2.5 mA=2.5×10−3 AI = 2.5 \, \text{mA} = 2.5 \times 10^{-3} \, \text{A}

    R=122.5×10−3=4.8×103 Ω=4.8 kΩR = \frac{12}{2.5 \times 10^{-3}} = 4.8 \times 10^{3} \, \Omega = 4.8 \, \text{k}\Omega

    Therefore, the resistance of the resistor is 4.8 kΩ4.8 \, \text{k}\Omega.

  9. 9

    Question 9

    A battery of 9 V is connected in series with resistors of 0.2 Ω, 0.3 Ω, 0.4 Ω, 0.5 Ω and 12 Ω, respectively. How much current would flow through the 12 Ω resistor?

    Medium
    2 marks
    Solve with AI
    Written solution

    Class 10 Physics Electricity

    The same current should flow through all the resistances and the circuit as everything is connected in series.

    V=IR⇒R=VIV = IR \quad \Rightarrow \quad R = \frac{V}{I}

    Where RR is the equivalent resistance.

    The sum of the resistances will give the value of RR.

    R=0.2+0.3+0.4+0.5+12=13.4 ΩR = 0.2 + 0.3 + 0.4 + 0.5 + 12 = 13.4 \, \Omega

    Potential difference, V=9 VV = 9 \, \text{V};

    I=913.4=0.672 AI = \frac{9}{13.4} = 0.672 \, \text{A}
  10. 10

    Question 10

    How many 176 Ω resistors (in parallel) are required to carry 5 A on a 220 V line?

    Medium
    2 marks
    Solve with AI
    Written solution

    Class 10 Physics Electricity

    Let’s assume the number of resistances to be xx.
    The equivalent resistance of resistors connected in parallel is given by

    1R=x176\frac{1}{R} = \frac{x}{176} ⇒R=176x\Rightarrow R = \frac{176}{x}

    Now, Ohm’s law is given as

    V=IR⇒R=VIV = IR \quad \Rightarrow \quad R = \frac{V}{I}

    Where,
    Supply voltage, V=220 VV = 220 \, \text{V}
    Current, I=5 AI = 5 \, \text{A}

    So, the equation can be written as,

    176x=2205\frac{176}{x} = \frac{220}{5} ⇒x=17644=4\Rightarrow x = \frac{176}{44} = 4

    Therefore, four resistors of 176 Ω176 \, \Omega are required to draw the given amount of current.

  11. 11

    Question 11

    Show how you would connect three resistors, each of resistance 6 Ω, so that the combination has a resistance of (i) 9 Ω, (ii) 4 Ω.

    Hard
    3 marks
    Solve with AI
    Written solution

    (i) 9 Ω\Omega

    Two resistors in parallel: Consider the following figure.

    Class 10 Physics Electricity

    Two 6 Ω6 \, \Omega resistors are connected in parallel. Their equivalent resistance will be

    R=116+16=6×66+6=3 ΩR = \frac{1}{\frac{1}{6} + \frac{1}{6}} = \frac{6 \times 6}{6 + 6} = 3 \, \Omega

    The third 6 Ω6 \, \Omega resistor is connected in series with 3 Ω3 \, \Omega.
    Hence, the equivalent resistance of the circuit is

    R=6 Ω+3 Ω=9 ΩR = 6 \, \Omega + 3 \, \Omega = 9 \, \Omega

    (ii) 4 Ω\Omega

    Two resistors in series: Consider the following figure.

    Class 10 Physics Electricity

    Two 6 Ω6 \, \Omega resistors are connected in series.
    Their equivalent resistance will be the sum R=6+6=12 ΩR = 6 + 6 = 12 \, \Omega.

    The third 6 Ω6 \, \Omega resistor is in parallel with 12 Ω12 \, \Omega.
    Hence, the equivalent resistance will be

    Req=1112+16=12×612+6=4 ΩR_{eq} = \frac{1}{\frac{1}{12} + \frac{1}{6}} = \frac{12 \times 6}{12 + 6} = 4 \, \Omega

    Therefore, the total resistance is 4 Ω4 \, \Omega.

  12. 12

    Question 12

    Several electric bulbs designed to be used on a 220 V electric supply line, are rated 10 W. How many lamps can be connected in parallel with each other across the two wires of 220 V line if the maximum allowable current is 5 A?

    Medium
    3 marks
    Solve with AI
    Written solution

    Class 10 Physics Electricity

    Resistance R1R_1 of one bulb is given by the expression,

    P1=V2R1⇒R1=V2P1P_1 = \frac{V^2}{R_1} \quad \Rightarrow \quad R_1 = \frac{V^2}{P_1}

    Where,
    Supply voltage, V=220 VV = 220 \, \text{V}
    Maximum allowable current, I=5 AI = 5 \, \text{A}
    Rating of an electric bulb, P1=10 WP_1 = 10 \, \text{W}.

    Resistance of one bulb is

    R1=(220)210=4840 ΩR_1 = \frac{(220)^2}{10} = 4840 \, \Omega

    Apply Ohm’s law to the circuit with all the bulbs,

    V=IRV = IR

    where RR is the total resistance of the circuit for xx number of electric bulbs.

    R=VI=2205=44 ΩR = \frac{V}{I} = \frac{220}{5} = 44 \, \Omega

    Resistance of each electric bulb, R1=4840 ΩR_1 = 4840 \, \Omega.
    Clearly, since the resistors are connected in parallel,

    1R=1R1×X\frac{1}{R} = \frac{1}{R_1} \times X X=R1R⇒X=484044=110X = \frac{R_1}{R} \quad \Rightarrow \quad X = \frac{4840}{44} = 110

    Hence, 110 bulbs can be connected in parallel.

  13. 13

    Question 13

    A hot plate of an electric oven connected to a 220 V line has two resistance coils A and B, each of 24 Ω resistance, which may be used separately, in series, or in parallel. What are the currents in the three cases?

    Hard
    3 marks
    Solve with AI
    Written solution

    Given: supply voltage V=220 VV = 220\ \text{V}, resistance of each coil R=24 ΩR = 24\ \Omega.

    Class 10 Physics Electricity

    The three cases: one coil alone, the two coils in series, and the two coils in parallel.

    a) Each coil used separately

    By Ohm's law, the current through one coil is

    I1=VR=22024≈9.17 AI_1 = \frac{V}{R} = \frac{220}{24} \approx 9.17\ \text{A}

    So a current of 9.179.17 A flows through a coil used on its own.

    b) Coils connected in series

    Rs=24 Ω+24 Ω=48 ΩR_s = 24\ \Omega + 24\ \Omega = 48\ \Omega I2=VRs=22048≈4.58 AI_2 = \frac{V}{R_s} = \frac{220}{48} \approx 4.58\ \text{A}

    So a current of 4.584.58 A flows when the coils are in series.

    c) Coils connected in parallel

    1Rp=124+124=224⇒Rp=12 Ω\frac{1}{R_p} = \frac{1}{24} + \frac{1}{24} = \frac{2}{24} \quad \Rightarrow \quad R_p = 12\ \Omega I3=VRp=22012≈18.33 AI_3 = \frac{V}{R_p} = \frac{220}{12} \approx 18.33\ \text{A}

    So a current of 18.3318.33 A is drawn from the line when the coils are in parallel.

  14. 14

    Question 14

    Compare the power used in the 2 Ω resistor in each of the following circuits:
    (i) A 6 V battery in series with 1 Ω and 2 Ω resistors, and
    (ii) A 4 V battery in parallel with 12 Ω and 2 Ω resistors.

    Medium
    3 marks
    Solve with AI
    Written solution

    Class 10 Physics Electricity

    (i) a 6 V battery in series with 1 Ω\Omega and 2 Ω\Omega resistors, and In the question it is given that V=6 VV = 6 \, \text{V}.
    1 Ω\Omega and 2 Ω\Omega resistors are connected in series.
    Therefore, the equivalent resistance of the circuit,

    R=1+2=3 ΩR = 1 + 2 = 3 \, \Omega

    According to Ohm’s law,

    V=IRV = IR

    Where,
    II is the current through the circuit.

    I=63=2 AI = \frac{6}{3} = 2 \, \text{A}

    In series, the same current flows in the entire circuit.
    Hence, the current flowing through the 2 Ω2 \, \Omega resistor is 2 A2 \, \text{A}.
    Power is given by the expression,

    P=I2R=22×2=8 WP = I^2 R = 2^2 \times 2 = 8 \, \text{W}

    (ii) a 4 V battery in parallel with 12 Ω\Omega and 2 Ω\Omega resistors.
    Potential difference, V=4 VV = 4 \, \text{V}.
    12 Ω12 \, \Omega and 2 Ω2 \, \Omega resistors are connected in parallel.
    The voltage across each component of a parallel circuit remains the same.
    Hence, the voltage across the 2 Ω2 \, \Omega resistor will be 4 V4 \, \text{V}.

    Power consumed by the 2 Ω2 \, \Omega resistor is given by

    P=V2R=422=8 WP = \frac{V^2}{R} = \frac{4^2}{2} = 8 \, \text{W}

    Therefore, the power used by the 2 Ω2 \, \Omega resistor is 8 W.

    Comparison: In both circuits the 2 Ω2 \, \Omega resistor dissipates exactly the same power, 8 W. In case (i) the current through it is 2 A, so the p.d. across it is V=IR=2×2=4V = IR = 2 \times 2 = 4 V. In case (ii) it has 4 V across it, so the current through it is I=V/R=4/2=2I = V/R = 4/2 = 2 A. It carries the same current (2 A) and has the same p.d. (4 V) in both circuits, so its power, P=VI=4×2=8P = VI = 4 \times 2 = 8 W, is the same.

  15. 15

    Question 15

    Two lamps, one rated 100 W at 220 V, and the other 60 W at 220 V, are connected in parallel to electric mains supply. What current is drawn from the line if the supply voltage is 220 V?

    Medium
    2 marks
    Solve with AI
    Written solution

    Class 10 Physics Electricity

    Both the bulbs are connected in parallel. Therefore, the potential difference across each bulb will be 220 V220\ \text{V} because the voltage remains the same in a parallel circuit.

    Current drawn by the bulb of rating 100 W100\ \text{W} is given by:

    I=PVI = \frac{P}{V} I=100220I = \frac{100}{220} I=0.4545 AI = 0.4545\ \text{A}

    Similarly, current drawn by the bulb of rating 60 W60\ \text{W} is given by:

    I=PVI = \frac{P}{V} I=60220I = \frac{60}{220} I=0.2727 AI = 0.2727\ \text{A}

    Hence, the total current drawn from the line is:

    Itotal=100220+60220I_{\text{total}} = \frac{100}{220} + \frac{60}{220} Itotal=0.727 AI_{\text{total}} = 0.727\ \text{A}
  16. 16

    Question 16

    Which uses more energy, a 250 W TV set in 1 hr, or a 1200 W toaster in 10 minutes?

    Medium
    2 marks
    Solve with AI
    Written solution

    Energy consumed by an electrical appliance is given by the expression,

    H=PtH = P t

    Where,
    Power of the appliance PP
    Time tt


    Energy consumed by a TV set of power 250 W in 1 hour:

    ETV=250×3600=9×105 JE_{\text{TV}} = 250 \times 3600 = 9 \times 10^5 \, \text{J}

    Energy consumed by a toaster of power 1200 W in 10 minutes:

    Etoaster=1200×600=7.2×105 JE_{\text{toaster}} = 1200 \times 600 = 7.2 \times 10^5 \, \text{J}

    Therefore, the energy consumed by a TV set of power 250 W in 1 hour is more than the energy consumed by a toaster of power 1200 W in 10 minutes.

    Class 10 Physics Electricity

  17. 17

    Question 17

    An electric heater of resistance 44 Ω draws 5 A from the service mains for 2 hours.
    Calculate the rate at which heat is developed in the heater.

    Medium
    2 marks
    Solve with AI
    Written solution

    Class 10 Physics Electricity

    Given: R=44 ΩR = 44\ \Omega, I=5 AI = 5\ \text{A}

    Rate of heat produced = Power consumed:

    P=I2R=52×44=25×44=1100 WP = I^2R = 5^2 \times 44 = 25 \times 44 = 1100\ \text{W}

    Therefore, heat is developed in the heater at the rate of 1100 J/s1100\ \text{J/s} (or 1100 W1100\ \text{W}).

  18. 18

    Question 18

    Explain the following:
    (a) Why is the tungsten used almost exclusively for filament of electric lamps?
    (b) Why are the conductors of electric heating devices, such as bread-toasters and electric irons, made of an alloy rather than a pure metal?
    (c) Why is the series arrangement not used for domestic circuits?
    (d) How does the resistance of a wire vary with its area of cross-section?
    (e) Why are copper and aluminium wires usually employed for electricity transmission?

    Hard
    5 marks
    Solve with AI
    Written solution

    (a) Tungsten is used for lamp filaments mainly because of its very high melting point (3380 ∘C3380\,^{\circ}\text{C}). A filament must become white hot to give out light, and tungsten can stay at that temperature without melting. Its resistivity is also higher than that of the copper connecting wires; since the filament and the wires carry the same current, most of the heat (H=I2RtH = I^2Rt) is produced in the thin tungsten coil. The bulb is filled with a chemically inactive gas such as nitrogen or argon to make the filament last longer.

    (b) Electric heating devices use alloys for their conductors because alloys have higher resistivity compared to pure metals. This means they produce more heat when electricity flows through them, which is necessary for heating appliances like toasters and irons. They also do not oxidise (burn) readily at high temperatures, unlike pure metals, which makes them more durable for repeated heating.

    The two reasons, side by side:

    Property of the alloy (e.g. nichrome)Why it matters in a heater
    Higher resistivity than a pure metalMore heat (H=I2RtH = I^2Rt) is produced for the same current
    Does not oxidise (burn) readily at high temperaturesThe element survives repeated heating

    (c) Series arrangements are not used in domestic circuits because:

    • Voltage is divided among all devices, so each device gets less than its required voltage.
    • If one device fails, the entire circuit stops working.
    • The total resistance increases, reducing the current flowing through the circuit.
    • The same current flows through every device, but different appliances need different currents (a heater needs far more than a bulb).
    • Devices cannot be switched on and off independently.

    In a parallel arrangement, every appliance gets the full mains voltage, draws the current it needs, and has its own switch, so one failing does not affect the others.

    Class 10 Physics Electricity

    (d) Resistance is inversely proportional to the wire's cross-sectional area, since R=ρlAR = \rho \dfrac{l}{A}. This means that as the cross-sectional area increases, the resistance decreases, and vice versa. A thicker wire has less resistance than a thinner one.

    (e) Copper and aluminium are used for electricity transmission because they are excellent conductors with low resistivity. This results in less power loss as heat and makes them efficient for carrying electricity over long distances.

Inside Ch 11

What Class 10 Science Ch 11 covers

The sections of the chapter, in the order the book takes them. Every question above comes from one of these.

  1. 01Electric Current and Circuit
  2. 02Electric Potential And Potential Difference
  3. 03Ohm's Law
  4. 04Symbols And Circuit Diagram
  5. 05Factors Affecting The Resistance Of A Conductor Depends
  6. 06Resistance Of A System Of Resistors
From the board papers

Ch 11 in past CBSE papers

The same chapter as the board has actually asked it. These are worded differently from the textbook exercise, which is the point of reading them.

  1. 1

    Board paper question 1

    A complete circuit is left on for several minutes, causing the connecting copper wire to become hot. As the temperature of the wire increases, the electrical resistance of the wire ?

    MCQEasyAsked 2023
    1 mark
    Solve with AI
    Answer
    • (A) decreases.

    • (B) remains the same.

    • (C) increases.

      Correct
    • (D) increases for some time and then decreases.

    Option (C) is correct.

    Explanation: Copper is a metal. As its temperature rises, the metal ions vibrate more vigorously and the moving electrons collide with them more often. This greater obstruction means a higher resistance, so the resistance of the wire increases as it gets hot.

    Class 10 Physics Electricity

    (A) is wrong: the resistance of a metal does not fall when it is heated. (B) is wrong: the resistance of a metal changes with temperature. (D) is wrong: nothing makes the resistance fall again; it keeps rising as the temperature rises.

  2. 2

    Board paper question 2

    Plastic insulation surrounds a wire having diameter dd and length ll as shown. A decrease in the resistance of the wire would be produced by an increase in the:

    Class 10 Physics Electricity

    MCQMediumAsked 2022
    1 mark
    Solve with AI
    Answer
    • (A) Diameter of the wire.

      Correct
    • (B) Length of the wire.

    • (C) Material resistivity of the wire.

    • (D) Plastic insulation.

    Option (A) is correct.

    The resistance of a wire is given by:

    R=ρlAR = \frac{\rho l}{A}

    Since the cross-sectional area of the metal wire is A=πd24A = \dfrac{\pi d^2}{4}, substituting:

    R=4ρlπd2R = \frac{4\rho l}{\pi d^2}

    where:

    • ρ\rho = resistivity of the material
    • ll = length of the wire
    • dd = diameter of the wire

    Checking each option:

    • (A) Diameter — R∝1d2R \propto \dfrac{1}{d^2}. A larger diameter gives a larger cross-sectional area, so the current has a wider path and the resistance decreases. Doubling dd makes RR one quarter.
    • (B) Length — R∝lR \propto l. A longer wire has more resistance, not less.
    • (C) Resistivity — R∝ρR \propto \rho. A material of higher resistivity gives more resistance.
    • (D) Plastic insulation — plastic is an insulator and carries no current. Thicker insulation does not change ρ\rho, ll or the area of the metal, so the resistance of the wire does not change.

    Only an increase in diameter lowers the resistance.

    Class 10 Physics Electricity

  3. 3

    Board paper question 3

    A cylindrical conductor of length ‘l’ and uniform area of cross-section ‘A’ has resistance ‘R’. The area of cross-section of another conductor of the same material and same resistance but of length ‘2l’ is:

    MCQMediumAsked 2022
    1 mark
    Solve with AI
    Answer
    • (A) A/2A / 2

    • (B) 3A/23A / 2

    • (C) 2A2A

      Correct
    • (D) 3A3A

    Option (C) is correct.

    The resistance of a conductor is:

    R=ρ lAR = \rho\,\frac{l}{A}

    where ρ\rho is the resistivity of the material, ll the length and AA the area of cross-section.

    Second conductor (same material, so same ρ\rho; length 2l2l; area A′A'; same resistance RR):

    R=ρ 2lA′R = \rho\,\frac{2l}{A'}

    Equating the two expressions for RR:

    ρ lA=ρ 2lA′\rho\,\frac{l}{A} = \rho\,\frac{2l}{A'}

    Cancelling ρ\rho and ll:

    1A=2A′⇒A′=2A\frac{1}{A} = \frac{2}{A'} \quad\Rightarrow\quad A' = 2A

    Doubling the length doubles the resistance, so the area must also double to bring it back to RR.

    Checking the other options (resistance of a 2l2l wire with each area):

    • (A) A/2A/2 — R′=ρ 2lA/2=4RR' = \rho\,\dfrac{2l}{A/2} = 4R. This is the trap: halving the area increases resistance.
    • (B) 3A/23A/2 — R′=43RR' = \dfrac{4}{3}R, still more than RR.
    • (D) 3A3A — R′=23RR' = \dfrac{2}{3}R, now less than RR.

    Hence, the area of cross-section is 2A2A.

    Class 10 Physics Electricity

  4. 4

    Board paper question 4

    When a 4V battery is connected across an unknown resistor, there is a current of 100 mA in the circuit. The value of the resistance of the resistor is:

    MCQEasyAsked 2020
    1 mark
    Solve with AI
    Answer
    • (A) 4 Ω

    • (B) 40 Ω

      Correct
    • (C) 400 Ω

    • (D) 0.4 Ω

    Option (B) is correct.

    Class 10 Physics Electricity

    We can use Ohm’s Law to find the resistance RR:

    V=I×RV = I \times R

    Rearranging to find RR:

    R=VIR = \frac{V}{I}

    Given:

    • Voltage V=4 VV = 4 \, \text{V}
    • Current I=100 mA=100×10−3 A=0.1 AI = 100 \, \text{mA} = 100 \times 10^{-3} \, \text{A} = 0.1 \, \text{A}

    Substituting the values into the equation:

    R=40.1=40 ΩR = \frac{4}{0.1} = 40 \, \Omega

    Thus, the value of the resistance is 40 Ω.

  5. 5

    Board paper question 5

    Two bulbs of 100 W and 40 W are connected in series. The current through the 100 W bulb is 1 A. The current through the 40 W bulb will be:

    MCQEasyAsked 2020
    1 mark
    Solve with AI
    Answer
    • (A) 0.4 A

    • (B) 0.6 A

    • (C) 0.8 A

    • (D) 1 A

      Correct

    Option (D) is correct.

    Class 10 Physics Electricity

    In a series connection, the current through each device remains the same. This is because the current that flows through all the components in a series circuit is the same.

    Given that the current through the 100 W bulb is 1 A, the current through the 40 W bulb will also be 1 A.

    Thus, the current through the 40 W bulb is 1 A.

  6. 6

    Board paper question 6

    What is the maximum resistance which can be made using five resistors, each of 15 Ω?

    MCQEasyAsked 2020
    1 mark
    Solve with AI
    Answer
    • (A) 15 Ω

    • (B) 10 Ω

    • (C) 75 Ω

      Correct
    • (D) 1 Ω

    Option (C) is correct.

    To get the maximum resistance, connect all five resistors in series. In series the resistances simply add, so every resistor you add makes the total larger:

    Rtotal=R1+R2+R3+R4+R5R_{\text{total}} = R_1 + R_2 + R_3 + R_4 + R_5

    With each resistor 15 Ω15\ \Omega:

    Rtotal=15+15+15+15+15=5×15=75 ΩR_{\text{total}} = 15 + 15 + 15 + 15 + 15 = 5 \times 15 = 75\ \Omega

    Checking the other options:

    • (A) 15 Ω is the resistance of just one resistor. Adding the other four in series can only increase it.
    • (B) 10 Ω is less than a single resistor. A total below 15 Ω15\ \Omega needs resistors in parallel, which lowers resistance, so it cannot be the maximum.
    • (D) 1 Ω is below even the smallest possible value. All five in parallel give 155=3 Ω\dfrac{15}{5} = 3\ \Omega, so 1 Ω1\ \Omega cannot be made at all.

    Thus, the maximum resistance is 75 Ω.

    Class 10 Physics Electricity

All 36 board paper questions for this chapter, solved the same way.

Common questions

Class 10 Science Ch 11 questions students ask

How many questions are there in Class 10 Science Ch 11?

18 questions. Every one is solved step by step on this page.

Are these Class 10 Physics question answers free?

Yes. Every question and its full working is free to read, with no account needed.

Can I download the Class 10 Physics Ch 11 solutions as a PDF?

There is no PDF to download. Every solution is on this page instead, which means it is searchable, always the current syllabus, and readable on a phone. Use your browser's print option if you want it on paper.