Opening your dashboard
Class 10 Physics Chapter 11 Electricity: Previous Year Questions
36 questions on Chapter 11, each solved step by step. Class 10 Physics, CBSE 2026-27.
36 questions with solutions
1–5 marks · Mixed difficulty
The first 33 solutions are on this page. This chapter is a long one, so the rest open on their own page to keep this one quick to load.
- 11 mark
Question 1
A complete circuit is left on for several minutes, causing the connecting copper wire to become hot. As the temperature of the wire increases, the electrical resistance of the wire ?
Solve with AIAnswer
(A) decreases.
(B) remains the same.
- Correct
(C) increases.
(D) increases for some time and then decreases.
Option (C) is correct.
Explanation: Copper is a metal. As its temperature rises, the metal ions vibrate more vigorously and the moving electrons collide with them more often. This greater obstruction means a higher resistance, so the resistance of the wire increases as it gets hot.

(A) is wrong: the resistance of a metal does not fall when it is heated. (B) is wrong: the resistance of a metal changes with temperature. (D) is wrong: nothing makes the resistance fall again; it keeps rising as the temperature rises.
- 21 mark
Question 2
Plastic insulation surrounds a wire having diameter and length as shown. A decrease in the resistance of the wire would be produced by an increase in the:
Solve with AIAnswer
- Correct
(A) Diameter of the wire.
(B) Length of the wire.
(C) Material resistivity of the wire.
(D) Plastic insulation.
Option (A) is correct.
The resistance of a wire is given by:
Since the cross-sectional area of the metal wire is , substituting:
where:
- = resistivity of the material
- = length of the wire
- = diameter of the wire
Checking each option:
- (A) Diameter — . A larger diameter gives a larger cross-sectional area, so the current has a wider path and the resistance decreases. Doubling makes one quarter.
- (B) Length — . A longer wire has more resistance, not less.
- (C) Resistivity — . A material of higher resistivity gives more resistance.
- (D) Plastic insulation — plastic is an insulator and carries no current. Thicker insulation does not change , or the area of the metal, so the resistance of the wire does not change.
Only an increase in diameter lowers the resistance.

- 31 mark
Question 3
A cylindrical conductor of length ‘l’ and uniform area of cross-section ‘A’ has resistance ‘R’. The area of cross-section of another conductor of the same material and same resistance but of length ‘2l’ is:
Solve with AIAnswer
(A)
(B)
- Correct
(C)
(D)
Option (C) is correct.
The resistance of a conductor is:
where is the resistivity of the material, the length and the area of cross-section.
Second conductor (same material, so same ; length ; area ; same resistance ):
Equating the two expressions for :
Cancelling and :
Doubling the length doubles the resistance, so the area must also double to bring it back to .
Checking the other options (resistance of a wire with each area):
- (A) — . This is the trap: halving the area increases resistance.
- (B) — , still more than .
- (D) — , now less than .
Hence, the area of cross-section is .

- 41 mark
Question 4
When a 4V battery is connected across an unknown resistor, there is a current of 100 mA in the circuit. The value of the resistance of the resistor is:
Solve with AIAnswer
(A) 4 Ω
- Correct
(B) 40 Ω
(C) 400 Ω
(D) 0.4 Ω
Option (B) is correct.

We can use Ohm’s Law to find the resistance :
Rearranging to find :
Given:
- Voltage
- Current
Substituting the values into the equation:
Thus, the value of the resistance is 40 Ω.
- 51 mark
Question 5
Two bulbs of 100 W and 40 W are connected in series. The current through the 100 W bulb is 1 A. The current through the 40 W bulb will be:
Solve with AIAnswer
(A) 0.4 A
(B) 0.6 A
(C) 0.8 A
- Correct
(D) 1 A
Option (D) is correct.

In a series connection, the current through each device remains the same. This is because the current that flows through all the components in a series circuit is the same.
Given that the current through the 100 W bulb is 1 A, the current through the 40 W bulb will also be 1 A.
Thus, the current through the 40 W bulb is 1 A.
- 61 mark
Question 6
What is the maximum resistance which can be made using five resistors, each of 15 Ω?
Solve with AIAnswer
(A) 15 Ω
(B) 10 Ω
- Correct
(C) 75 Ω
(D) 1 Ω
Option (C) is correct.
To get the maximum resistance, connect all five resistors in series. In series the resistances simply add, so every resistor you add makes the total larger:
With each resistor :
Checking the other options:
- (A) 15 Ω is the resistance of just one resistor. Adding the other four in series can only increase it.
- (B) 10 Ω is less than a single resistor. A total below needs resistors in parallel, which lowers resistance, so it cannot be the maximum.
- (D) 1 Ω is below even the smallest possible value. All five in parallel give , so cannot be made at all.
Thus, the maximum resistance is 75 Ω.

- 71 mark
Question 7
An electric bulb is connected to a 220V generator. The current is 0.50 A. What is the power of the bulb?
Solve with AIAnswer
(A) 440 W
- Correct
(B) 110 W
(C) 55 W
(D) 0.0023 W
Option (B) is correct.

We are given:
- Voltage (V) = 220 V
- Current (I) = 0.50 A.
The formula to calculate power (P) is:
Substituting the given values:
Conclusion:
The power of the bulb is:
- 81 mark
Question 8
Which of the following represents voltage?
Solve with AIAnswer
(A) Work done × Current × Time
(B) Work done × Charge
(C) Work done × Time / Current
- Correct
(D) Work done / Charge
Option (D) is correct.
Voltage (also known as potential difference) is defined as the work done per unit charge. The correct relationship is:
Where:
- is the voltage,
- is the work done,
- is the charge.
Thus, the correct option is (D) Work done / Charge.
- 91 mark
Question 9
The maximum resistance which can be made using four resistors, each of resistance , is:
Solve with AIAnswer
- Correct
(A) 2 Ω
(B) 1 Ω
(C) 2.5 Ω
(D) 8 Ω
Option (A) is correct.
To obtain the maximum resistance, all resistors should be connected in series.
In a series connection, total resistance is the sum of individual resistances:
Given each resistor has ,
Thus, the maximum resistance that can be made is 2 Ω.

- 101 mark
Question 10
Unit of electric power may also be expressed as:
Solve with AIAnswer
- Correct
(A) Volt-ampere
(B) Kilowatt-hour
(C) Watt-second
(D) Joule-second
Option (A) is correct.
Electric power is given by the formula:
where
= Power,
= Potential difference (in volts),
= Current (in amperes).Therefore, the unit of electric power can also be expressed as volt-ampere.
- 111 mark
Question 11
A cylindrical conductor of length 'l' and uniform area of cross section 'A' has resistance 'R'. The area of cross section of another conductor of the same material and same resistance but of length '2l' is:
Solve with AIAnswer
- Correct
(A) 2A
(B)
(C) A/2
(D) 3A
Option (A) is correct.
The resistance of a conductor is:
where is the resistivity of the material, the length and the area of cross-section.
Second conductor (same material, so same ; length ; area ; same resistance ):
Equating the two expressions for :
Cancelling and :
Doubling the length doubles the resistance, so the area must also double to bring it back to .
Checking the other options (resistance of a wire with each area):
- (B) — , still more than .
- (C) — . This is the trap: halving the area increases resistance.
- (D) — , now less than .
Hence, the area of cross-section is .

- 121 mark
Question 12
Which element will be used for electrical transmission lines?
Solve with AIAnswer
(A) Iron
- Correct
(B) Copper
(C) Tungsten
(D) Mercury
Option (B) is correct.
Copper is preferred for electrical transmission lines because:
Property Copper Resistivity Very low ( m at 20 °C) Conductivity Very high Ductility Can be drawn into long, thin wires easily Durability Corrodes far less than iron Since resistance is given by:
a material with low resistivity () has low resistance, so less electrical energy is lost as heat along the line. NCERT notes that copper and aluminium are generally used for electrical transmission lines.
Why the other three are wrong (resistivities from NCERT Table 11.2)
- (A) Iron does conduct, but its resistivity ( m) is about 6 times that of copper, so the same cable would waste about six times as much energy as heat. Iron also rusts.
- (C) Tungsten has a very high melting point (3380 °C), which is why it is used for lamp filaments, not cables. Its resistivity ( m) is over 3 times copper's.
- (D) Mercury is a liquid at room temperature, so it cannot be drawn into a wire or strung between towers. Its resistivity ( m) is also about 58 times copper's.

- 131 mark
Question 13
At the time of short circuit, the electric current in the circuit:
Solve with AIAnswer
(A) vary continuously
(B) does not change
(C) reduces substantially
- Correct
(D) increases heavily
Option (D) is correct.
At the time of a short circuit, the live and neutral wires touch directly. The current no longer has to pass through the appliance, so the resistance of the circuit drops to nearly zero. Since and the supply voltage stays the same, a very small makes the current increase heavily — enough to overheat the wires and damage devices.
So the current does not reduce (C), does not stay the same (B), and does not keep varying (A); it jumps to a very large value.
Hence, the correct option is (D).

- 141 mark
Question 14
Two bulbs of 100 W and 40 W are connected in series. The current through the 100 W bulb is 1 A. The current through the 40 W bulb will be:
Solve with AIAnswer
(A) 0.4A
(B) 0.6A
(C) 0.8A
- Correct
(D) 1A
Option (D) is correct.

Explanation: In a series connection there is only one path, so the same current flows through every component. The current through the 40 W bulb is therefore also 1 A.
The power ratings fix each bulb's resistance, and the two resistances together set how large the one series current is, but they cannot make the current differ from one bulb to the other.
(A), (B) and (C) all give the 40 W bulb a different current from the 100 W bulb, which is impossible in series.
- 151 mark
Question 15
Why is nichrome wire used in many electrical heating devices?
Solve with AIAnswer
(A) It has low resistivity and low melting point.
(B) It has high resistivity and low melting point.
(C) It has low resistivity and high melting point.
- Correct
(D) It has high resistivity and high melting point.
Option (D) is correct.
Explanation: Nichrome, an alloy of nickel and chromium, is used for heating elements because:
- It has a high resistivity ( m in NCERT Table 11.2, against m for copper), so a short coil of it has the large resistance needed to turn a lot of electrical energy into heat.
- It has a high melting point, so it can glow red hot without melting.
- It does not oxidise (burn) readily at high temperatures, so it lasts through repeated heating.

(A) and (C) are wrong: a low-resistivity wire would have to be impractically long and thin to give enough resistance. (B) is wrong: a low melting point would let the element melt when red hot.
- 163 marks
Question 16
A V-I graph for a nichrome wire is given below. What do you infer from this graph? Draw a labelled circuit diagram to obtain such a graph.
Solve with AIWritten solution
Inference from the graph: The – graph for the nichrome wire is a straight line passing through the origin. So and the ratio is constant: the wire obeys Ohm's law, and its resistance stays constant over this range.
With on the vertical axis, the slope of the graph is the resistance. Using the points and :
Circuit diagram:

The circuit contains:
- A battery of cells, connected through a key (K).
- The nichrome wire XY.
- An ammeter (A) in series with the wire, to measure the current .
- A voltmeter (V) connected across XY, in parallel with it, to measure the potential difference .
Close the key and note the readings of the ammeter and the voltmeter. Repeat with one, two, three and four cells in the battery to get several pairs of readings, then plot against . (A rheostat in series with the wire can be used instead to vary the current.)
- 173 marks
Question 17
What is electrical resistivity? Derive its S.I. unit.
Solve with AIWritten solution
Electrical resistivity of a material is the resistance of a conductor of that material having unit length () and unit area of cross-section ().
For a conductor of length and area of cross-section ,
where is the resistivity of the material. Rearranging,
S.I. unit: resistance is measured in ohm (), area in square metre () and length in metre (), so
The S.I. unit of resistivity is the ohm metre ().

- 183 marks
Question 18
In a series electrical circuit comprising a resistor made up of a metallic wire, the ammeter reads 100 mA. If the length of the wire is doubled, how will the current in the circuit change? Justify your answer.
Solve with AIWritten solution

Given: the ammeter reads , and the length of the wire is doubled.
The resistance of a wire is . For the same material and the same area of cross-section, , so doubling the length doubles the resistance of the wire: .
The wire is the only significant resistance in the circuit (the resistance of the cell, the ammeter and the connecting wires is negligible), and the cell keeps the same potential difference across it. By Ohm's law, , so doubling halves the current:
The current is halved: the ammeter now reads .
- 193 marks
Question 19
Calculate the resistance of a 1 km long copper wire of area of cross-section . The resistivity of copper is -meter.
Solve with AIWritten solution
We can calculate the resistance using the formula:
Where:
- = Resistance of the wire (in ohms),
- = Resistivity of the material (in ohm-meter),
- = Length of the wire (in meters),
- = Area of cross-section of the wire (in square meters).
Given:
- Resistivity of copper, ,
- Length of the wire, ,
- Area of cross-section, .
Substituting the values into the formula:
Thus, the resistance of the wire is 8.115 ohms (≈ 8.12 Ω). The resistance of the copper wire is 8.115 Ω.

- 203 marks
Question 20
(a) List the factors on which the resistance of a conductor in the shape of a wire depends ?
(b) Why are metals good conductors of electricity, whereas glass is a bad conductor of electricity? Give reason.
(c) Why are alloys commonly used in electrical heating devices? Give reason.
Solve with AIWritten solution
(a) The resistance of a wire depends on:
- Length (): — a longer wire has more resistance.
- Area of cross-section (): — a thicker wire has less resistance.
- Nature of the material: each material has its own resistivity .
Together, these give .
Resistance also changes with temperature: for a metal it increases as the temperature rises, because the vibrating metal ions get in the way of the moving electrons more often. It increases with temperature but is not directly proportional to it.
(b) Metals contain a large number of free electrons that are not bound to any one atom. When a potential difference is applied, these electrons drift through the metal and carry the current, so metals have a very low resistivity.
In glass the electrons are tightly bound to their atoms and there are practically no free electrons, so glass has an extremely high resistivity and does not conduct.
(c) Alloys are used in heating devices such as electric irons, toasters and heaters because:
- An alloy has a higher resistivity than the metals it is made from, so a convenient length of wire gives the large resistance needed for heating.
- An alloy such as nichrome does not oxidise (burn) readily at high temperatures, so the element can stay red hot for long periods.

- 215 marks
Question 21
(a) An electric iron consumes energy at a rate of 880 W when heating is at the maximum rate and 330 W when heating is at the minimum. If the source voltage is 220 V, calculate the current and resistance in each case.
(b) What is the heating effect of electric current?
Solve with AIWritten solution
(a)
At Maximum Heating (, ):
Current:
Resistance:
At Minimum Heating (, ):
Current:
Resistance:
(b)
When electric current flows through a conductor, the free electrons collide with the atoms of the conductor. These collisions cause the atoms to vibrate, releasing energy in the form of heat. This is called the heating effect of electric current.
The heat produced is given by Joule's Law:
where is current, is resistance and is time.
This effect is used in electric irons, geysers, toasters and electric heaters.
- 223 marks
Question 22
Fill in the blanks
1.The SI unit of current is ……… .
2.According to ……… Law, the potential difference across the ends of a resistor is directly proportional to the ……… through it, provided its ……… remains constant.
3.The resistance of a conductor depends directly on its ……… , inversely on its ……… and also on the ……… of the conductor.
4.The SI unit of resistivity is ……… .
5.If the potential difference across the ends of a conductor is doubled, the current flowing through it, gets ……… .
Solve with AIWritten solution
1.ampere
2.According to Ohm’s Law, the potential difference across the ends of a resistor is directly proportional to the current through it, provided its temperature remains constant.
3.The resistance of a conductor depends directly on its length, inversely on its area of cross-section, and also on the material of the conductor.
4.The SI unit of resistivity is ohm-metre (Ω m).
5.If the potential difference across the ends of a conductor is doubled, the current flowing through it, gets doubled.
- 235 marks
Question 23
An electric lamp of resistance 20 Ω and a conductor of resistance 4 Ω are connected to a 6 V battery as shown in the circuit. Calculate:

(a) The total resistance of the circuit.
(b) The current through the circuit.
(c) The potential difference across:
(i) The electric lamp
(ii) The conductor
(d) The power of the lamp.
Solve with AIWritten solution
(a) Total resistance of the circuit:
The total resistance of the circuit is the sum of the individual resistances, as they are connected in series.
Substituting the given values:
(b) Current through the circuit:
Using Ohm’s Law:
Where:
- (voltage of the battery),
- (total resistance).
Substitute the values:
Thus, the current through the circuit is 0.25 A.
(c) Potential difference across:
(i) Electric lamp:
For the electric lamp, the potential difference is given by:
Substituting the values:
(ii) Conductor:
For the conductor, the potential difference is given by:
Substituting the values:
(d) Power of the lamp:
The power of the electric lamp is given by:
We already know:
- (potential difference across the lamp),
- (current through the circuit).
Substitute the values:
Summary:
- (a) Total resistance = 24 Ω
- (b) Current = 0.25 A
- (c) Potential difference across electric lamp = 5 V, Potential difference across conductor = 1 V
- (d) Power of the lamp = 1.25 W
- 243 marks
Question 24
100 J of heat is produced each second in a 4Ω resistor. The potential difference across the resistor will be:
Solve with AIWritten solution
The heat produced in a resistor in time is given by Joule's law of heating:
Here of heat is produced each second, so the rate of heating (the power) is
For a resistor, , so
The potential difference across the resistor is .
Note that and are powers, in watts. The heat in joules also needs the time: .
- 255 marks
Question 25
(a) Define Power and state its S.I. unit ?
(b) A torch bulb is rated 5 V and 500 mA. Calculate ?
(i) Power
(ii) Resistance
(iii) Energy consumed when it is lighted for 2½ hours.
Solve with AIWritten solution
(a)
Power is the rate at which work is done or energy is transferred in a circuit. In terms of electric circuits, it is the rate at which electrical energy is converted into other forms of energy, such as heat, light, or mechanical energy.
Mathematically, power is given by:
Where:
- = Power (in watts, W),
- = Work or energy (in joules, J),
- = Time (in seconds, s).
The S.I. unit of power is the watt (W), which is defined as one joule per second:

(b)
Given:
- Voltage (V) = 5 V
- Current (I) = 500 mA = 0.5 A
- Time (t) = 2½ hours = seconds
(i) Power:
Using the formula for power:
Substituting the values:
Thus, the power consumed by the torch bulb is 2.5 W.
(ii) Resistance:
Using Ohm's law, , we can solve for resistance:
Substituting the values:
Thus, the resistance of the torch bulb is 10 Ω.
(iii) Energy consumed:
The energy consumed is given by the formula:
Substituting the values:
Thus, the energy consumed when the bulb is lighted for 2½ hours is 22,500 J.
Summary:
- (i) Power = 2.5 W
- (ii) Resistance = 10 Ω
- (iii) Energy consumed = 22,500 J
- 265 marks
Question 26
The diagram given is a schematic diagram of a household circuit. The house shown in the diagram has 5 usable spaces where electrical connections are made. For this house, the mains have a voltage of 220 V and the net current coming from the mains is 22 A.

(a) What is the mode of connection to all the spaces in the house from the mains?
(b) The spaces 5 and 4 have the same resistance, and spaces 3 and 2 have respective resistances of 20 Ω and 30 Ω. Space 1 has a resistance double that of space 5. What is the net resistance for space 5?
(c) What is the current in space 3?
(d) What should be placed between the main connection and the rest of the house’s electrical appliances to save them from accidental high electric current?
Solve with AIWritten solution
(a)
All spaces in the house are connected in parallel. This is because each space has its own independent connection to the mains and receives the full voltage from the mains (220 V). In parallel connections, the voltage across each space is the same.
(b)
Let the resistance of space 5 (and space 4, since they are the same) be .
Then, the resistance of space 1 is , the resistance of space 2 is 30 Ω, and the resistance of space 3 is 20 Ω.The total current from the mains is 22 A and the mains voltage is 220 V.
Using Ohm’s law:
Now, for the parallel combination of resistors, the reciprocal of the total resistance is the sum of the reciprocals of the individual resistances:
Substitute the given resistances:
Simplify the equation:
The least common denominator of 30 and 20 is 60, so:
Now substitute this back into the equation:
Multiply everything by 60 to eliminate the denominators:
Subtract 5 from both sides:
Solve for :
Thus, the resistance for space 5 is 150 Ω.
(c)
The current in space 3 can be calculated using Ohm’s law:
Where:
- (voltage across space 3),
- (resistance of space 3).
Substitute the values:
Thus, the current in space 3 is 11 A.
(d)
An electric fuse should be placed between the main connection and the rest of the house's electrical appliances. A fuse is a safety device that protects the circuit from excess current by melting and breaking the circuit if the current exceeds a safe limit. This prevents damage to electrical appliances from high surges in current
- 273 marks
Question 27
(a) State Ohm’s law. Represent it mathematically ?
(b) Define 1 ohm ?
(c) What is the resistance of a conductor through which a current of 0.5 A flows when a potential difference of 2 V is applied across its ends ?
Solve with AIWritten solution
(a) Ohm's Law:
Ohm’s Law states that the current flowing through a conductor is directly proportional to the potential difference (voltage) across its ends, provided the temperature and other physical conditions remain constant.
Mathematically, it is represented as:
Where:
- is the potential difference (voltage) across the conductor, in volts (V),
- is the current through the conductor, in amperes (A),
- is the resistance of the conductor, in ohms ().
(b) Definition of 1 Ohm:
1 ohm is defined as the resistance of a conductor when a current of 1 ampere flows through it under a potential difference of 1 volt.
Mathematically, this is expressed as:
(c) Resistance Calculation:
Given:
- Current ()
- Potential difference ().
Using Ohm's Law, we can calculate the resistance (R):
Substituting the values:
Conclusion:
- (a) Ohm’s law is ().
- (b) 1 ohm is the resistance when 1 volt of potential difference produces 1 ampere of current.
- (c) The resistance of the conductor is 4 ohms.

- 283 marks
Question 28
The current flowing through a resistor connected in a circuit and the potential difference developed across its ends are as shown in the diagram by milliammeter and voltmeter readings respectively.

(a) What are the least counts of these meters?
(b) What is the resistance of the resistor?
Solve with AIWritten solution
(a) On the milliammeter the numbered marks are apart, and there are divisions between two numbered marks, so
Note that here is the gap between two numbered marks, not the maximum reading of the meter, which is .
On the voltmeter the numbered marks are apart, with divisions between them, so
(b) The meters read and . By Ohm's law,
The resistance of the resistor is .
- 293 marks
Question 29
Why are the heating elements of electric toasters and electric irons made of an alloy rather than a pure metal?
Solve with AIWritten solution
The heating elements of electric toasters and electric irons are made of alloys rather than pure metals because alloys have higher resistivity than their constituent metals.
This higher resistivity allows the alloy to produce more heat for a given current, making it suitable for heating applications. Alloys also do not oxidise (burn) readily even at high temperatures, unlike pure metals, adding to their durability in repeated-heating applications.

- 302 marks
Question 30
Some work is done to move a charge from infinity to a point A in space. The potential of the point A is given as .
What is the work done to move this charge from infinity in terms of and ?
Solve with AIWritten solution
The work done in moving a charge from infinity to a point at potential is given by:
It is the product of the charge and the potential at that point.
Here the potential at infinity is taken as zero, so is the potential difference between infinity and A: the work done per unit charge in bringing a charge from infinity to A. Multiplying by the charge gives the total work.
The unit of work done is volt-coulomb (or joule).
- 315 marks
Question 31
(a) An electric iron consumes energy at a rate of 880 W when heating is at the maximum rate and 330 W when heating is at the minimum.
If the source voltage is 220 V, calculate the current and resistance in each case.
(b) What is the heating effect of electric current ?
(c) Find an expression for the amount of heat produced when a current passes through a resistor for some time ?
Solve with AIWritten solution
(a)
At Maximum Heating (, ):
At Minimum Heating (, ):
(b)
When electric current flows through a conductor, the free electrons collide with the atoms causing them to vibrate and release energy as heat. This is called the heating effect of electric current.
(c)
Consider a current flowing through a resistor of resistance for time .
The work done by the electric source:
If all of this work is converted into heat, the heat produced is . Since :
This is Joule's Law of Heating — the heat produced is directly proportional to the square of the current, to the resistance and to the time.
- 325 marks
Question 32
(a) Three resistors are connected in parallel, and the combination is connected to a battery, ammeter, voltmeter, and key. Draw a suitable circuit diagram and obtain an expression for the equivalent resistance of the combination of the resistors.
(b) Calculate the equivalent resistance of the following network:
Solve with AIWritten solution
(a) — Parallel Combination
Circuit diagram: , and are connected between the same two junctions. The ammeter is in the main wire, the voltmeter is across the combination, and the battery and key complete the circuit.

Let be the equivalent resistance of , , connected in parallel across voltage .
Since voltage is the same across all resistors:
Total current:
Dividing throughout by :
(b) — Network Calculation

and are in parallel:
is in series with a resistor:
- 335 marks
Question 33

In the given circuit, A, B, C and D are four lamps connected with a battery of 60 V.
Analyse the circuit to answer the following questions:
(i) What kind of combination are the lamps arranged in (series or parallel) ?
(ii) Write any two advantages of this combination of lamps ?
(iii) Explain with calculations which lamp glows the brightest ?
(iv) Find the total resistance of the circuit ?
Solve with AIWritten solution
(i)
The lamps are connected in parallel, as indicated by the circuit diagram, where each lamp is connected across the same two points of the battery. In a parallel combination, each lamp gets the full potential of the battery.(ii)
The advantages of parallel connection are:
- Independent operation of lamps: If one lamp is faulty or switched off, it will not affect the operation of the other lamps.
- Each lamp gets the full voltage: All lamps receive the same voltage from the battery, which ensures each lamp operates at its rated brightness and power.
(iii)
The lamp with the highest power will glow the brightest. The power of each lamp is given by the formula:
Where:
- is the power,
- is the voltage across the lamp (60 V),
- is the current through the lamp.
Given:
- Lamp A: ,
- Lamp B: ,
- Lamp C: ,
- Lamp D: ,
Conclusion:
Lamp C has the highest current (5 A), so it has the highest power of 300 W, and thus it will glow the brightest.(iv)
To find the total resistance in a parallel circuit, we use the formula:
We can find the resistance of each lamp using Ohm's law:
Substitute the given values for each lamp:
- For Lamp A:
- For Lamp B:
- For Lamp C:
- For Lamp D:
Now, substitute these into the parallel resistance formula:
Take the LCM of 20, 15 and 12, which is 60:
Thus,
Check using the total current. In parallel, the currents in the branches add up:
Conclusion:
The total resistance of the circuit is 4 Ω. - 345 marks
Question 34
A bulb is rated 40 W, 220 V. Find the current drawn by it, when it is connected to a 220 V supply. Also, find its resistance. If the given bulb is replaced by a bulb of rating 25 W, 220 V, will there be any change in the value of current and resistance? Justify your answer and determine the change.
- 351 mark
Question 35
Directions: In the following questions, a statement of Assertion (A) is followed by a statement of Reason (R). Mark the correct choice as:
Assertion (A):
A conductor has charge.Reason (R):
Conductor has gained two electrons. - 361 mark
Question 36
Assertion: The resistance of a conductor is directly proportional to its length and inversely proportional to its area of cross-section.
Reason: Longer conductors have more resistance because there is a longer path for the current to travel, while larger cross-sectional areas allow for easier current flow.
