Confirming your payment

Skip to content

Opening your dashboard

Class 12 Physics Chapter 13 Alternating Currents: Competency-Based Questions (CBQ)

80 questions on Chapter 13, each worked through on its own page with the AI tutor. Class 12 Physics, CBSE 2026-27.

80 questions

1–5 marks · Mixed difficulty

  1. 1

    Question 1

    In an ac circuit, the voltage and current are V=150sin⁡(150t)V = 150\sin(150t) V and I=150sin⁡(150t+π3)I = 150\sin\left(150t + \frac{\pi}{3}\right) A. The average power dissipated in the circuit is

    MCQMedium
    1 mark
  2. 2

    Question 2

    The voltage across a circuit is v=200sin⁡ωtv = 200\sin\omega t volt and the current in it is i=5sin⁡(ωt−π6)i = 5\sin\left(\omega t - \frac{\pi}{6}\right) ampere. The average power consumed is

    MCQEasy
    1 mark
  3. 3

    Question 3

    An ac voltage v=100sin⁡(100πt)v = 100\sin(100\pi t) volt is applied across a 50 Ω resistor. The heat produced in the resistor in one minute is

    MCQEasy
    1 mark
  4. 4

    Question 4

    The phasor diagram of the voltage across a single circuit element and the current through it, at some instant, is shown. The element is

    Class 12 Physics Alternating Currents

    MCQEasy
    1 mark
  5. 5

    Question 5

    A capacitor is connected to an ac source. If the capacitance is halved and the frequency of the source is doubled, keeping the rms voltage the same, the rms current

    MCQMedium
    1 mark
  6. 6

    Question 6

    In a series LCR circuit, the rms voltage of the source is 50 V, the voltage across the resistor is 40 V, and the voltage across the capacitor is 60 V. The voltage across the inductor is

    MCQMedium
    1 mark
  7. 7

    Question 7

    A pure inductor has a reactance of 20 Ω on a 50 Hz supply and draws 11 A from it. The same rms voltage is applied at a frequency of 200 Hz. The current now is

    MCQMedium
    1 mark
  8. 8

    Question 8

    In a series RL circuit connected to an ac source, the rms voltage across the resistor is 60 V and across the inductor is 80 V. The rms source voltage and the phase of the current relative to it are

    MCQEasy
    1 mark
  9. 9

    Question 9

    A current in a wire is i=3+4sin⁡ωti = 3 + 4\sin\omega t ampere (a steady part plus an alternating part). Its rms value is

    MCQEasy
    1 mark
  10. 10

    Question 10

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R).

    Assertion (A): A pure inductor connected to an ac source carries a current but consumes no power on average.

    Reason (R): Its current lags the voltage by π/2\pi/2, so the instantaneous power is positive for one quarter cycle and equally negative for the next.

    MCQMedium
    1 mark
  11. 11

    Question 11

    The rating of a filament bulb is given as 50 W, 100 V. This bulb is to be used in a house where the power supply is at 200 V, 50 Hz. Determine the inductance of the coil that must be connected in series to the bulb, so that it glows to its maximum power rating, but doesn't fuse.

    Medium
    3 marks
  12. 12

    Question 12

    A step-down transformer operates from a 2200 V supply and delivers 4.4 kW to a load at 220 V. Its efficiency is 90%.

    (a) Find the current in the secondary and in the primary.

    (b) How much power is lost in the transformer?

    (c) Name two causes of this loss and how each is reduced in practice.

    Medium
    3 marks
  13. 13

    Question 13

    An ac circuit connected to a 220 V supply draws 5.0 A, and a wattmeter shows that it consumes 880 W. Find (a) the power factor, (b) the resistance of the circuit, and (c) its net reactance.

    Medium
    2 marks
  14. 14

    Question 14

    In a series LCR circuit connected to an ac source, voltmeters across the resistor, the inductor and the capacitor read 30 V, 90 V and 50 V respectively.

    (a) Find the rms voltage of the source.

    (b) Find the power factor, and state whether the current leads or lags.

    (c) The three readings add up to 170 V. Explain why this is much more than the source voltage.

    Medium
    3 marks
  15. 15

    Question 15

    The potential difference VV and the current ii flowing through an instrument in an ac circuit of frequency ff are given by V=5cos⁡ωtV = 5\cos\omega t volts and i=2sin⁡ωti = 2\sin\omega t amperes (ω=2πf\omega = 2\pi f). The power dissipated in the instrument is:

    Medium
    2 marks
  16. 16

    Question 16

    A resistor of 100 Ω and a capacitor are connected in series to a 50 Hz supply. The reactance of the capacitor also equals 100 Ω.

    (a) Find the capacitance.

    (b) By what angle, and by what time, does the current lead the voltage?

    Medium
    2 marks
  17. 17

    Question 17

    A circuit containing two elements in series is connected to v=10sin⁡(100πt)v = 10\sin(100\pi t) volt, and the current is i=2sin⁡(100πt+π6)i = 2\sin\left(100\pi t + \frac{\pi}{6}\right) ampere.

    (a) Draw the voltage and current phasors at t=0t = 0.

    (b) Which two elements does the circuit contain? Explain.

    (c) Find their values.

    Medium
    3 marks
  18. 18

    Question 18

    An electric heater is rated 1.0 kW, 220 V, for use on the 50 Hz mains.

    (a) Find its resistance and the rms current it draws.

    (b) Find the peak current and the peak voltage.

    (c) How much energy does it use in one hour? Why must the insulation of its wiring be able to withstand more than 220 V?

    Medium
    3 marks
  19. 19

    Question 19

    A coil of resistance 5.0 Ω draws 2.0 A from a 220 V, 50 Hz supply.

    (a) Find its inductance.

    (b) What current would it draw from a 220 V, 60 Hz supply?

    (c) What would happen if it were connected by mistake to a 220 V dc supply?

    Medium
    3 marks
  20. 20

    Question 20

    A power station sends 100 kW to a town through a line of total resistance 2.0 Ω.

    (a) Find the power lost in the line if the power is sent at 1000 V.

    (b) Find the power lost if it is first stepped up to 20 kV.

    (c) Explain why power is transmitted at high voltage.

    Medium
    3 marks
  21. 21

    Question 21

    In a resistor connected to an ac source, the ratio of the maximum instantaneous power to the average power is

    MCQEasy
    1 mark
  22. 22

    Question 22

    An ac ammeter in a circuit reads 2.0 A. The current in the circuit actually varies between

    MCQMedium
    1 mark
  23. 23

    Question 23

    A bulb is connected in series with a capacitor across an ac source of variable frequency. As the frequency is increased at constant rms voltage, the bulb

    MCQMedium
    1 mark
  24. 24

    Question 24

    A capacitor of 50π\frac{50}{\pi} µF is connected to an ac source v=100sin⁡(100πt)v = 100\sin(100\pi t) volt. The current through it at t=0t = 0 is

    MCQMedium
    1 mark
  25. 25

    Question 25

    At the instant when the current through a pure inductor connected to an ac source is at its maximum, the voltage across the inductor is

    MCQMedium
    1 mark
  26. 26

    Question 26

    In a series LCR circuit the rms voltages across R, L and C are 40 V, 70 V and 40 V respectively. The rms source voltage and the phase relation are

    MCQMedium
    1 mark
  27. 27

    Question 27

    A series LCR circuit resonates at angular frequency ω0\omega_0. A second capacitor, identical to the first, is connected in parallel with it. The new resonant angular frequency is

    MCQMedium
    1 mark
  28. 28

    Question 28

    A series LCR circuit is driven at a frequency higher than its resonant frequency. Which statement is correct?

    MCQMedium
    1 mark
  29. 29

    Question 29

    In an ac circuit the rms current is 10 A and it lags the voltage by 60°. The wattless component of the current is

    MCQMedium
    1 mark
  30. 30

    Question 30

    A resistor and an inductor with XL=RX_L = R are in series across an ac source. A capacitor with XC=XLX_C = X_L is now added in series. The average power consumed by the circuit

    MCQMedium
    1 mark
  31. 31

    Question 31

    An ideal step-down transformer converts 220 V to 22 V and supplies a 110 W lamp connected to its secondary. The current drawn from the 220 V supply is

    MCQMedium
    1 mark
  32. 32

    Question 32

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R).

    Assertion (A): A transformer cannot step up a steady dc voltage.

    Reason (R): A steady current in the primary produces a constant flux in the core, and a constant flux induces no emf in the secondary.

    MCQMedium
    1 mark
  33. 33

    Question 33

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R).

    Assertion (A): Two ac voltages of 3 V and 4 V (rms), of the same frequency but 90∘90^\circ out of phase, are connected in series. The resultant rms voltage is 5 V, not 7 V.

    Reason (R): Ac voltages of the same frequency add as phasors, taking their phase difference into account.

    MCQMedium
    1 mark
  34. 34

    Question 34

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R).

    Assertion (A): A moving-coil ammeter designed for dc reads zero when connected in a 50 Hz ac circuit, even though a current is flowing.

    Reason (R): The deflecting torque on its coil is proportional to the current and reverses 100 times a second. The coil cannot follow such rapid reversals, so it responds to the average current over a cycle, which is zero.

    MCQMedium
    1 mark
  35. 35

    Question 35

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R).

    Assertion (A): For the same useful power delivered to a load, a lower power factor requires a higher current from the supply.

    Reason (R): Useful power P=VrmsIrmscos⁡ϕP = V_{rms}I_{rms}\cos\phi; for fixed PP and VrmsV_{rms}, if cos⁡ϕ\cos\phi decreases, IrmsI_{rms} must increase to maintain the same PP.

    MCQMedium
    1 mark
  36. 36

    Question 36

    Passage: A 100 W incandescent bulb is rated for 220 V ac at 50 Hz. When connected to the household supply (220 V rms, 50 Hz) it glows at its rated brightness. A student finds that a 220 V dc supply gives the same brightness, while a 311 V dc supply (equal to the peak of the 220 V ac supply) makes it noticeably brighter and may burn it out.

    Question: Why do 220 V dc and 220 V (rms) ac produce the same heating in the bulb, while the 311 V peak of the ac does not decide its brightness?

    MCQMedium
    1 mark
  37. 37

    Question 37

    Passage: A fluorescent tube uses a choke coil (an inductor) in series with the tube to limit the current. An ideal inductor has no resistance and consumes no average power, so it limits the current without wasting energy, unlike a series resistor. A choke of L=0.5L = 0.5 H and negligible resistance is used on a 220 V, 50 Hz supply with a tube of equivalent resistance R=40R = 40 Ω.

    Question: The current through the tube (and choke) is

    MCQMedium
    1 mark
  38. 38

    Question 38

    A series circuit has R=40R = 40 Ω, L=0.13L = 0.13 H and C=10C = 10 µF, connected to v=1002sin⁡(1000t)v = 100\sqrt2\sin(1000t) volt. Find:

    (a) the reactances and the impedance,

    (b) the rms current and its phase relative to the voltage,

    (c) the average power,

    (d) the rms voltage across each element,

    (e) the angular frequency at which the current would be largest.

    Medium
    5 marks
  39. 39

    Question 39

    A series circuit with L=0.50L = 0.50 H, C=20C = 20 µF and R=25R = 25 Ω is connected to a variable-frequency source of 100 V (rms).

    (a) Find the resonant frequency.

    (b) Find the rms current at resonance.

    (c) Find the rms voltage across the inductor at resonance, and comment on it.

    Medium
    3 marks
  40. 40

    Question 40

    A workshop motor. A workshop runs an electric motor from a 230 V, 50 Hz supply. An ammeter shows that it draws 10 A, and a wattmeter shows that it consumes 1610 W. Like most motors, it is an inductive load. The electricity board asks the owner to improve the power factor.

    (a) Find the power factor of the motor.

    (b) Find its power component and wattless component of current.

    (c) What current would the supply need to provide if the power factor were 1, for the same 1610 W?

    (d) Why does the board care about the power factor, and what device can the owner connect to improve it?

    Medium
    4 marks
  41. 41

    Question 41

    An LCR series circuit is connected to an ac supply of angular frequency ω=100\omega = 100 rad/s. Given R=100 ΩR = 100\ \Omega, L=500L = 500 mH and C=5 μC = 5\ \muF, study the following statements carefully.

    I. The circuit is dominantly capacitive.

    II. The current in the circuit leads the applied voltage.

    III. If ω\omega is made greater than 20010200\sqrt{10} rad/s, the circuit becomes dominantly inductive.

    IV. The circuit can be made capacitive or inductive simply by changing the angular frequency of the supply, keeping its peak voltage constant.

    MCQMedium
    1 mark
  42. 42

    Question 42

    In an ac circuit containing only a resistor RR, the power dissipated is P1P_1. A capacitor CC is then added in series, and the power dissipated in the resistor becomes P2P_2. Next, an inductor LL replaces the capacitor, and the power becomes P3P_3.

    If the reactance of the capacitor equals the reactance of the inductor, which relation is correct?

    MCQMedium
    1 mark
  43. 43

    Question 43

    A series LCR circuit draws a current I0I_0 at its resonant angular frequency ω0\omega_0, where the inductive reactance is twice the resistance. The source is now tuned to ω0/2\omega_0/2, keeping the same rms voltage. The new current is

    MCQMedium
    1 mark
  44. 44

    Question 44

    A 5 Ω resistor, a 5 mH inductor and a 5 µF capacitor are joined in series and resonate with an ac source at angular frequency ω0\omega_0. If only the resistance is changed to 10 Ω, the circuit resonates at ω1\omega_1. If instead only the inductance is changed to 20 mH, the circuit resonates at ω2\omega_2. The ratio ω1ω2\dfrac{\omega_1}{\omega_2} is

    MCQMedium
    1 mark
  45. 45

    Question 45

    Which of the following ac circuits dissipates the maximum average power?

    MCQMedium
    1 mark
  46. 46

    Question 46

    The four graphs below show the instantaneous power pp in four ac circuits. Each circuit contains a resistor, a capacitor or an inductor, alone or in combination.

    Class 12 Physics Alternating Currents

    Study the following statements and select the correct option.

    I. The average power in (2) and (3) is zero.

    II. Graph (1) is for a resistor, and its average power is Pav=VrmsIrmsP_{av} = V_{rms}I_{rms}.

    III. Graph (4) is for an LCR combination, and its average power is positive.

    MCQMedium
    1 mark
  47. 47

    Question 47

    The voltmeter V in the circuit shown is connected across the resistor only. What does it read?

    Class 12 Physics Alternating Currents

    MCQMedium
    1 mark
  48. 48

    Question 48

    An alternating current is given by i=i1cos⁡ωt+i2sin⁡ωti = i_1\cos\omega t + i_2\sin\omega t. Its rms value is

    MCQMedium
    1 mark
  49. 49

    Question 49

    A current i=4sin⁡(100πt)i = 4\sin(100\pi t) ampere flows through a pure inductor of inductance 1π\frac{1}{\pi} H. At t=1300t = \frac{1}{300} s, the voltage across the inductor and the rate at which energy is transferred are

    MCQMedium
    1 mark
  50. 50

    Question 50

    An ideal step-down transformer has 10 times as many turns on its primary as on its secondary. A 5 Ω resistor is connected across the secondary, and the primary is connected to 220 V ac. As seen from the 220 V supply, the transformer and its load behave like a resistance of

    MCQMedium
    1 mark
  51. 51

    Question 51

    In a series LCR circuit, the inductive and capacitive reactances are 400 Ω and 600 Ω respectively, and the resistance is 100 Ω. The peak voltage of the ac supply is 100 V. Find:

    (a) the impedance of the circuit,

    (b) the peak current,

    (c) the peak voltage across each element,

    (d) the sum of these three peak voltages.

    (e) Can the sum found in (d) ever appear across the circuit? Give a reason.

    Medium
    5 marks
  52. 52

    Question 52

    A series LCR circuit is capacitive when the ac supply has angular frequency ω1\omega_1, with phase angle Φ=−30∘\Phi = -30^\circ. When the supply is changed to angular frequency ω2\omega_2, keeping its peak voltage constant, the circuit becomes inductive with phase angle Φ=+30∘\Phi = +30^\circ.

    What is the change in the power delivered to the circuit? Explain your answer.

    Medium
    3 marks
  53. 53

    Question 53

    An LCR circuit is connected to an ac supply of fixed peak voltage and frequency. The peak current is ImaxI_{max}, and the resistance RR equals the inductive reactance XLX_L.

    When the separation between the capacitor plates is doubled, the current falls to half.

    Find the original relation between the resistance RR and the capacitive reactance XCX_C.

    Medium
    3 marks
  54. 54

    Question 54

    An ac source of peak voltage 100 V and frequency 50 Hz is connected across a 1 µF capacitor. At t=0t = 0 the energy stored in the capacitor is zero. Find:

    (a) the current in the capacitor at t=1100t = \frac{1}{100} s,

    (b) the maximum current in the circuit.

    Medium
    3 marks
  55. 55

    Question 55

    The ratio of the number of turns in the primary to the secondary of a transformer is 1 : 10. The load draws 1.2 A from the secondary. Find the current in the primary if the efficiency of the transformer is only 90%.

    Medium
    2 marks
  56. 56

    Question 56

    An ac supply is rated at 80 V. A series LCR circuit connected to it draws 5 A. Find the range of values of the average power that the source can deliver to the circuit.

    Hard
    2 marks
  57. 57

    Question 57

    The household supply is 200 V, 60 Hz. Find the time taken

    (a) for the current to rise from zero to its rms value,

    (b) for the voltage to fall from its rms value to zero.

    Medium
    2 marks
  58. 58

    Question 58

    An alternating current of frequency 8 kHz is sent through a telephone line 100 km long, whose capacitance is 0.01 µF per km. What inductance must be connected in series with the line so that the current is maximum?

    Hard
    2 marks
  59. 59

    Question 59

    A coil of resistance RR and inductance LL is connected to a power supply.

    On a 50 V dc supply, a current of 0.5 A flows through it.

    On a 50 V, 50 Hz ac supply, a current of 0.2 A flows through it.

    Find RR and LL.

    Medium
    3 marks
  60. 60

    Question 60

    An inductor LL is connected to an ac source of frequency ν\nu. As the current varies sinusoidally, the inductor's core goes through alternate cycles of magnetisation and demagnetisation.

    One magnetisation followed by one demagnetisation takes 8 ms. Find the frequency ν\nu of the source.

    Medium
    2 marks
  61. 61

    Question 61

    In a series RC circuit on an ac supply, the current leads the voltage by 45∘45^\circ. If the frequency of the supply is doubled, keeping the voltage the same, the current will lead the voltage by

    MCQMedium
    1 mark
  62. 62

    Question 62

    In a series LCR circuit, ac voltmeters across R, L and C read 60 V, 60 V and 40 V respectively. Consider these statements:

    I. The source voltage is 160 V.

    II. The circuit is inductive, and the current lags the source voltage.

    III. The power factor is about 0.95.

    IV. If the source frequency is increased slightly, the voltmeter across C will read more.

    Which statements are correct?

    MCQHard
    1 mark
  63. 63

    Question 63

    Two ac sources, v1=10sin⁡ωtv_1 = 10\sin\omega t volt and v2=10sin⁡(ωt+2π3)v_2 = 10\sin\left(\omega t + \frac{2\pi}{3}\right) volt, are connected in series. The resultant voltage is

    MCQMedium
    1 mark
  64. 64

    Question 64

    In a series LCR circuit on a 50 Hz supply, the inductive reactance is 20 Ω and the capacitive reactance is 80 Ω. The circuit will resonate at

    MCQMedium
    1 mark
  65. 65

    Question 65

    In a series LCR circuit, the net reactance ∣XL−XC∣|X_L - X_C| is three times the resistance, and the average power is PP. The resistance is now tripled, with the source, LL, CC and the frequency unchanged. The new average power is

    MCQMedium
    1 mark
  66. 66

    Question 66

    The primary of a transformer has 500 turns and is connected to a 220 V (rms), 50 Hz supply. Neglecting losses, the peak magnetic flux in the core is about

    MCQMedium
    1 mark
  67. 67

    Question 67

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R).

    Assertion (A): A capacitor connected to an ac source carries a current because charges flow across the gap between its plates.

    Reason (R): The current in the wires connected to a capacitor is i=Cdvdti = C\dfrac{dv}{dt}.

    MCQMedium
    1 mark
  68. 68

    Question 68

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R).

    Assertion (A): In a series LCR circuit, the power factor has the same value, 12\frac{1}{\sqrt2}, at the two frequencies (one below and one above resonance) at which the current is 12\frac{1}{\sqrt2} of its value at resonance.

    Reason (R): At each of these frequencies ∣XL−XC∣=R|X_L - X_C| = R, so Z=2 RZ = \sqrt2\,R.

    MCQHard
    1 mark
  69. 69

    Question 69

    Two statements are given below. One is labelled Assertion (A) and the other is labelled Reason (R).

    Assertion (A): When nothing is connected to the secondary of a transformer, its primary, though connected across the mains, takes almost no power from the supply.

    Reason (R): With the secondary open, the primary behaves almost as a pure inductor of large reactance. Its small current lags the voltage by nearly 90∘90^\circ.

    MCQMedium
    1 mark
  70. 70

    Question 70

    Passage: A factory uses large induction motors, which are highly inductive loads. The combined load of P=100P = 100 kW operates at 400 V (rms), 50 Hz, with a power factor of cos⁡ϕ=0.6\cos\phi = 0.6 (lagging). The electricity board charges the factory for the apparent power (kVA), not the true power (kW). To reduce its costs, the factory installs a capacitor bank in parallel with the motors. The capacitors draw a leading current that cancels part of the motors' lagging current, bringing the power factor closer to 1. This is called power-factor correction.

    Question: Before correction, the current drawn from the supply is

    MCQMedium
    1 mark
  71. 71

    Question 71

    A radio's tuning circuit is a coil of fixed inductance LL in series with a variable capacitor that can be set anywhere from 50 pF to 500 pF. It must tune across the medium-wave band, from 540 kHz to 1708 kHz.

    (a) Show that this capacitor range is just enough, and find LL.

    (b) To what capacitance must it be set to receive a station broadcasting at 1000 kHz?

    (c) Why does the circuit pick up one station strongly, while the others, all present at the aerial together, are not heard?

    Medium
    3 marks
  72. 72

    Question 72

    A transformer has a primary of 1100 turns, connected to 220 V ac, and two separate secondaries: one of 60 turns and one of 550 turns. The 60-turn secondary lights a 24 W lamp, and the 550-turn secondary supplies a heater of resistance 55 Ω. Treat the transformer as ideal.

    (a) Find the voltage across each secondary.

    (b) Find the current in each load.

    (c) Find the current in the primary. What would it become if the lamp burnt out?

    Medium
    3 marks
  73. 73

    Question 73

    A 100 Ω resistor is connected in series with a capacitor across a 220 V, 50 Hz supply, and the current is found to lead the voltage by 60∘60^\circ.

    (a) Find the capacitance.

    (b) What inductance must be added in series to make the power factor 1?

    (c) By what factor does the power consumed change when it is added?

    Medium
    3 marks
  74. 74

    Question 74

    A series LCR circuit is driven by a source of fixed voltage and variable frequency.

    (a) Show that if the current has the same value at two angular frequencies ω1\omega_1 and ω2\omega_2, then ω1ω2=ω02\omega_1\omega_2 = \omega_0^2, where ω0\omega_0 is the resonant angular frequency.

    (b) The circuit resonates at 1000 rad/s, and it draws a certain current at 800 rad/s. At what other angular frequency will it draw the same current?

    Hard
    3 marks
  75. 75

    Question 75

    A workshop load takes 2.2 kW from a 220 V, 50 Hz supply at a power factor of 0.6 (lagging).

    (a) Find the current drawn, and split it into its power component and its wattless component.

    (b) What capacitance, connected in parallel with the load, would raise the power factor to 1?

    (c) What current does the supply then provide? Does the load itself receive any less power?

    (d) Why is the capacitor connected in parallel with the load, not in series?

    Medium
    5 marks
  76. 76

    Question 76

    A pure inductor of 0.20 H is connected to a 220 V, 50 Hz supply.

    (a) Find the maximum energy stored in its magnetic field.

    (b) How many times per second is this energy stored and given back to the source?

    (c) What is the average power consumed, and the average energy stored?

    Medium
    3 marks
  77. 77

    Question 77

    A coil (with both resistance and inductance) is connected in series with a capacitor to a 100 V, 50 Hz supply. The current is 1.0 A. A voltmeter reads 150 V across the coil and 200 V across the capacitor.

    (a) Explain why the coil's voltage and the capacitor's voltage cannot simply be added.

    (b) Find the resistance and the inductance of the coil, and the capacitance.

    (c) Find the power factor, and state whether the current leads or lags.

    (d) At what frequency would this circuit resonate?

    Hard
    5 marks
  78. 78

    Question 78

    Speed regulators. A ceiling fan is rated 110 W at 220 V, 50 Hz. For this case study, treat it as a resistive load. To run it slowly, its current must be halved. Older regulators did this with a series resistor. Better ones used a series choke (an inductor of negligible resistance).

    (a) Find the fan's resistance and its normal current.

    (b) What series resistance halves the current? How much power is then wasted in the regulator?

    (c) What inductance would halve the current instead? How much power is wasted in it?

    (d) Find the power drawn from the mains in each case, and the power factor with the choke. Which regulator is better, and why?

    Medium
    5 marks
  79. 79

    Question 79

    In an ac circuit, the instantaneous power delivered by the source swings between a maximum of +160 W and a minimum of −40 W. The average power and the power factor of the circuit are

    MCQMedium
    1 mark
  80. 80

    Question 80

    A resistor and a capacitor are in series across a 200 V ac supply. Voltmeters across the resistor and across the capacitor read 120 V and 160 V.

    (a) Explain why the readings add up to more than 200 V, and find the phase angle.

    (b) The frequency of the supply is doubled, keeping 200 V. Find the new readings of the two voltmeters.

    Medium
    3 marks