Opening your dashboard
Class 12 Physics Chapter 12 Semiconductor Electronics, Devices And Circuits: Previous Year Questions
37 questions on Chapter 12, each solved step by step. Class 12 Physics, CBSE 2026-27.
37 questions with solutions
1–5 marks · Hard difficulty
- 11 mark
Question 1
During the formation of a - junction,
Solve with AIAnswer
(A) diffusion current keeps increasing.
(B) drift current remains constant.
(C) both the diffusion current and drift current remain constant.
- Correct
(D) diffusion current remains almost constant but drift current increases till both currents become equal.
Option (D) is correct.
Explanation: When the junction is first formed, electrons diffuse from the -side to the -side and holes from the -side to the -side because of the concentration difference, so the diffusion current is large while the drift current is small.
Each carrier that crosses leaves behind an immobile ion, so layers of positive ions (on the -side) and negative ions (on the -side) build up. Their electric field, directed from to , grows as more charge is uncovered, and it drives an increasing drift current in the opposite direction. The process stops when the drift current becomes equal to the diffusion current, and the junction is then in equilibrium.
The diffusion current does not keep increasing (A), and the drift current does not stay constant (B, C): it is the drift current that grows until the two balance.
- 21 mark
Question 2
The energy required by an electron to jump the forbidden band in silicon at room temperature is about
Solve with AIAnswer
(A) 0.01 eV
(B) 0.05 eV
(C) 0.7 eV
- Correct
(D) 1.1 eV
Option (D) is correct.
Explanation: To jump the forbidden band an electron must go from the top of the valence band to the bottom of the conduction band, so it needs at least the energy gap . For silicon at room temperature
The other values belong to different processes: about 0.05 eV (B) is the energy needed to free the extra electron of a donor atom in silicon, about 0.01 eV (A) is the same energy in germanium, and 0.7 eV (C) is the energy gap of germanium.
- 31 mark
Question 3
In an extrinsic semiconductor, the number density of holes is . If the number density of intrinsic carriers is , the number density of electrons in it is
Solve with AIAnswer
(A)
(B)
- Correct
(C)
(D)
Option (C) is correct.
Explanation: In thermal equilibrium the electron and hole concentrations satisfy
So
The semiconductor is -type: holes are the majority carriers and electrons are far fewer than even the intrinsic value. Option (A) halves the correct value and (B) and (D) do not follow from .
- 41 mark
Question 4
The formation of depletion region in a - junction diode is due to
Solve with AIAnswer
(A) movement of dopant atoms
- Correct
(B) diffusion of both electrons and holes
(C) drift of electrons only
(D) drift of holes only
Option (B) is correct.
Explanation: The electron concentration is higher on the -side, so electrons diffuse from to ; the hole concentration is higher on the -side, so holes diffuse from to . Each diffusing electron leaves behind a positive donor ion on the -side, and each diffusing hole leaves behind a negative acceptor ion on the -side. These immobile ions near the junction form a region with no free carriers: the depletion region.
The dopant atoms themselves are fixed in the lattice and do not move (A). Drift (C, D) is caused by the field of the depletion region after it has formed; it opposes the diffusion, it does not create the region.
- 51 mark
Question 5
A semiconductor device is connected in series with a battery, an ammeter and a resistor. A current flows in the circuit. If the polarity of the battery is reversed, the current in the circuit almost becomes zero. The device is
Solve with AIAnswer
(A) intrinsic semiconductor
(B) -type semiconductor
(C) -type semiconductor
- Correct
(D) - junction diode
Option (D) is correct.
Explanation: The device conducts for one polarity and practically stops conducting when the polarity is reversed, so its resistance depends on the direction of the applied voltage. That is the behaviour of a - junction diode: in forward bias the barrier is lowered and a current of the order of mA flows; in reverse bias the barrier is raised and only a tiny current of the order of µA flows.
A piece of intrinsic, -type or -type semiconductor (A, B, C) behaves like an ordinary resistor: the same current flows whichever way the battery is connected.
- 61 mark
Question 6
In an unbiased - junction at equilibrium, which of the following statements is true about diffusion current and drift current?
Solve with AIAnswer
- Correct
(A) Diffusion current is equal to drift current
(B) Drift current exists while diffusion current is zero
(C) Diffusion current exists while drift current is zero
(D) Neither drift current nor diffusion current exists
Option (A) is correct.
Explanation: Both currents flow in an unbiased junction. Carriers still diffuse across because of the concentration difference, and the field of the depletion region still sweeps carriers back. At equilibrium the two currents are equal in magnitude and opposite in direction, so the net current through the junction is zero.
Options (B), (C) and (D) switch one or both currents off, but equilibrium is a balance between two currents that are both present, not the absence of current.
- 71 mark
Question 7
Hole is
Solve with AIAnswer
(A) an anti-particle of electron.
- Correct
(B) a vacancy created when an electron leaves a covalent bond.
(C) absence of free electrons.
(D) an artificially created particle.
Option (B) is correct.
Explanation: In Si or Ge each atom shares its four valence electrons with its neighbours in covalent bonds. When thermal energy frees one of these electrons, it leaves a vacancy in the bond. This vacancy behaves like a particle with an effective charge and is called a hole. An electron from a neighbouring bond can jump into it, so the hole appears to move.
A hole is not the positron, the anti-particle of the electron (A). It is a missing bonding electron, not just an absence of free electrons (C), and it is a way of describing the bound electrons, not a particle that is made artificially (D).
- 81 mark
Question 8
In a reverse-biased - junction diode, the applied voltage mostly drops across
Solve with AIAnswer
(A) -region only
(B) -region only
- Correct
(C) depletion region
(D) the diode
Option (C) is correct.
Explanation: The depletion region has almost no free charge carriers, so its resistance is very high compared with that of the - and -regions, which contain many majority carriers. These regions are in series and carry the same current, so the voltage across each is proportional to its resistance: almost the whole applied voltage appears across the depletion region. In reverse bias this voltage adds to the barrier, raising it to and widening the depletion region.
Options (A) and (B) are the low-resistance regions, across which only a tiny voltage appears. Option (D) is true only in the trivial sense that the whole applied voltage is across the diode; the question asks which part of the diode takes it, so (C) is the intended answer.
- 91 mark
Question 9
In the figure, assuming the diodes to be ideal,
Solve with AIAnswer
(A) is forward biased and is reverse biased and hence current flows from A to B
- Correct
(B) is forward biased and is reverse biased and hence no current flows from B to A and vice versa
(C) and are both forward biased and hence current flows from A to B
(D) and are both reverse biased and hence no current flows from A to B and vice versa
Option (B) is correct.
Explanation: B is at 0 V and A is at −10 V, so B is at the higher potential. A current, if any, would have to flow from B to A.
- Along that path the current first passes through from B upwards, in the direction of its arrow, so is forward biased.
- It would then have to pass through from right to left, against its arrow, so is reverse biased.
The two diodes are connected back to back, so one of them always blocks the path and no current flows in either direction. Option (A) gets the directions the wrong way round, and in (C) and (D) the two diodes cannot both have the same bias, since they point in opposite directions along the path.
- 101 mark
Question 10
In the circuit shown in the figure, if the diode forward voltage drop is 0.3 V, the voltage difference between A and B is
Solve with AIAnswer
(A) 1.3 V
- Correct
(B) 2.3 V
(C) 0 V
(D) 0.5 V
Option (B) is correct.
Explanation: No steady current flows into the capacitor branch, so the whole 0.2 mA flows from A to B through the two resistors and the forward-biased diode in series:
Option (A) counts only one resistor, and (D) adds the diode drop to a single 0.2 V term.
- 111 mark
Question 11
In the given figure, a diode D is connected to an external resistance and an emf of 3.5 V. If the barrier potential developed across the diode is 0.5 V, the current in the circuit will be
Solve with AIAnswer
(A) 40 mA
(B) 20 mA
(C) 35 mA
- Correct
(D) 30 mA
Option (D) is correct.
Explanation: The diode is forward biased (its -side is connected towards the positive terminal), and 0.5 V of the emf is used up across it. The rest appears across the resistor:
Option (C) ignores the barrier potential (), and (A) adds it instead of subtracting it.
- 121 mark
Question 12
In which of the following figures is the - diode reverse biased?
Solve with AIAnswer
(A)

(B)

- Correct
(C)

(D)

Option (C) is correct.
Explanation: A diode is reverse biased when its -side (the flat side of the triangle) is at a lower potential than its -side (the bar). In each figure one end of the diode is at the terminal potential and the other end is connected through to the other terminal.
- (A) -side at −12 V, -side connected to −5 V: the -side is higher, so it is forward biased.
- (B) -side at 0 V, -side connected to −10 V: higher, forward biased.
- (C) -side at 0 V, -side connected to +5 V: the -side is lower, so it is reverse biased.
- (D) -side at +5 V, -side connected to +10 V: higher, forward biased.
Only circuit (C) is reverse biased.
- 131 mark
Question 13
Based on the V-I characteristics of the diode, we can classify the diode as
Solve with AIAnswer
(A) bilateral device
(B) ohmic device
- Correct
(C) non-ohmic device
(D) passive element
Option (C) is correct.
Explanation: For an ohmic device the V-I graph is a straight line through the origin, so is constant. The V-I characteristic of a diode is not a straight line: the current stays almost zero until the threshold voltage and then rises steeply, and in reverse bias it stays tiny. Its resistance changes with the applied voltage, so the diode is a non-ohmic device.
A diode conducts well in one direction only, so it is unilateral, not bilateral (A), and it is not ohmic (B). "Passive element" (D) says nothing about its V-I characteristic.
- 141 mark
Question 14
Two identical - junctions are connected in series with a battery in three different ways, as shown in the figure. The potential drops across the two junctions are equal in
Solve with AIAnswer
(A) circuits (1) and (2)
- Correct
(B) circuits (2) and (3)
(C) circuits (1) and (3)
(D) circuit (1) only
Option (B) is correct.
Explanation: The positive terminal of the battery is on the left in every circuit.
- Circuit (1): the first junction (P on the left, joined to +) is forward biased, but the second (N on the left) is reverse biased. The two junctions are in opposite states, so almost all the battery voltage appears across the reverse-biased one: the drops are unequal.
- Circuit (2): both junctions have P towards the positive terminal, so both are forward biased and, being identical, share the voltage equally.
- Circuit (3): both have N towards the positive terminal, so both are reverse biased; the same tiny current flows through identical junctions, so the drops are again equal.
The drops are equal in circuits (2) and (3).
- 151 mark
Question 15
The V-I characteristic of a silicon diode is shown in the figure. The ratio of the resistance of the diode at mA to the resistance at V is
Solve with AIAnswer
(A) 100
(B)
(C) 10
- Correct
(D)
Option (D) is correct.
Explanation: At mA (forward bias): treat the characteristic between 10 mA and 20 mA as a straight line. From the graph, mA at 0.7 V and mA at 0.8 V, so
At V (reverse bias): the current is µA, so
Ratio:
Option (B) is the ratio the other way round (reverse to forward).
- 162 marks
Question 16
Two halves of a silicon crystal (A and B) are doped with arsenic and boron respectively, forming a - junction in it. A battery is connected across it as shown in the figure.

(a) Will the junction be forward biased or reverse biased? Give reason.
(b) Draw the V-I graph for this arrangement.
Solve with AIWritten solution
(a) Arsenic is pentavalent (a donor), so half A is -type. Boron is trivalent (an acceptor), so half B is -type.
In the figure the positive terminal of the battery (the long plate) is connected to A, the -side, and the negative terminal to B, the -side. The applied voltage therefore adds to the barrier potential, so the junction is reverse biased.
(b) In reverse bias only a very small current (of the order of µA) flows, carried by minority carriers. It stays almost constant as the reverse voltage is increased, until the breakdown voltage is reached, where it increases sharply.

- 173 marks
Question 17
The graph shows the variation in hole concentration with doping concentration in an extrinsic semiconductor doped with pentavalent impurities.

Why does the hole concentration reduce when pentavalent doping is increased?
Solve with AIWritten solution
A pentavalent impurity is a donor: each atom gives one free electron, so the number of free electrons rises far above the number produced thermally.
Holes are still produced by breaking covalent bonds, but with so many more free electrons around, a hole is much more likely to meet an electron and recombine. The rate of recombination therefore rises and the hole concentration falls.
The more donors are added, the more free electrons there are, and the smaller the hole concentration becomes. In equilibrium
and the larger the donor concentration, the smaller the hole concentration, which is the falling curve in the graph.
- 182 marks
Question 18
The figure shows a piece of pure semiconductor S in series with a variable resistor R and a source of constant voltage V. Should the value of R be increased or decreased to keep the reading of the ammeter constant, when semiconductor S is heated? Justify your answer.
Solve with AIWritten solution
When the pure (intrinsic) semiconductor is heated, more covalent bonds break and more electron-hole pairs are produced. With more charge carriers available, the resistance of S decreases.
The source voltage is constant, so a smaller total resistance would make the current, and the ammeter reading, increase.
To keep the current the same, the total resistance of the circuit must stay the same. The value of R must therefore be increased by the same amount as the resistance of S has fallen.
- 193 marks
Question 19
Two crystals and , made of pure silicon, are doped with arsenic and aluminium respectively.
(i) Identify the extrinsic semiconductors so formed.
(ii) Why is doping of intrinsic semiconductors necessary?
Solve with AIWritten solution
(i) Arsenic is pentavalent. Four of its five valence electrons form bonds with the neighbouring Si atoms and the fifth is very weakly bound, so it becomes a free electron. is therefore an -type semiconductor (electrons are the majority carriers).
Aluminium is trivalent. It can bond with only three neighbours, leaving a vacancy (hole) in the fourth bond. is therefore a -type semiconductor (holes are the majority carriers).
(ii) At room temperature very few covalent bonds in a pure semiconductor are broken, so its conductivity is very low and useful devices cannot be made from it. Adding a suitable impurity at the level of a few parts per million increases the number of charge carriers enormously, and so increases the conductivity many times. Doping also lets us choose which carrier (electrons or holes) is in the majority, which is needed to make a - junction.
- 202 marks
Question 20
A -type Si semiconductor is made by doping an average of one dopant atom per silicon atoms. If the number density of silicon atoms in the specimen is atoms m⁻³, find the number of holes created per cubic centimetre in the specimen due to doping. Also give one example of such dopants.
Solve with AIWritten solution
Each dopant atom (a trivalent acceptor) creates one hole, so the number of holes created per m³ equals the number of dopant atoms per m³:
Since ,
Example of such a dopant: a trivalent element such as aluminium, indium, boron or gallium.
- 211 mark
Question 21
Assertion (A): We cannot form a - junction diode by taking a slab of a -type semiconductor and physically joining it to another slab of an -type semiconductor.
Reason (R): In a -type semiconductor , while in an -type semiconductor .
Solve with AIAnswer
(A) Both Assertion (A) and Reason (R) are true, and Reason (R) is the correct explanation of Assertion (A).
(B) Both Assertion (A) and Reason (R) are true, but Reason (R) is not the correct explanation of Assertion (A).
- Correct
(C) Assertion (A) is true, but Reason (R) is false.
(D) Assertion (A) is false, and Reason (R) is also false.
Option (C) is correct.
Explanation: The Assertion is true: however flat two slabs are made, their surfaces are rough on a scale much larger than the spacing between atoms (about 2–3 Å), so they would touch only at a few points. There would be no continuous contact at the atomic level, and the join would act as a discontinuity for the charge carriers instead of a proper junction.
The Reason is false: it has the carriers the wrong way round. In a -type semiconductor holes are the majority carriers (), and in an -type semiconductor electrons are the majority carriers ().
- 223 marks
Question 22
Write any two distinguishing features between conductors, semiconductors and insulators on the basis of energy band diagrams.
Solve with AIWritten solution
The electrons of a solid occupy two bands of energy levels: the valence band (the levels of the valence electrons) and, above it, the conduction band. The difference between the bottom of the conduction band and the top of the valence band is the energy gap .

(a) Metal: the conduction band either overlaps the valence band or is partly filled (). Electrons can move into empty levels with almost no extra energy, so a large number are available for conduction and the resistance is low.
(b) Insulator: there is a large gap, eV. The valence band is full and the conduction band is empty, and thermal energy cannot lift electrons across so large a gap, so there is practically no conduction.
(c) Semiconductor: there is a small gap, eV (for example 1.1 eV for Si and 0.7 eV for Ge). At room temperature some electrons gain enough energy to cross into the conduction band, leaving holes in the valence band, so a small conduction is possible; its resistance lies between those of metals and insulators.
- 233 marks
Question 23
(i) Draw the energy band diagrams of (a) -type and (b) -type semiconductor at temperature K.
(ii) In the case of -type semiconductor, the donor energy level is slightly below the bottom of the conduction band, whereas in -type semiconductor, the acceptor energy level is slightly above the top of the valence band. Explain what role these energy levels play in conduction and valence bands.
Solve with AIWritten solution
(i) In the diagrams, filled dots are electrons and open circles are holes.

In the -type semiconductor the donor level lies just below ; most of the electrons in the conduction band have come from the donors, and only a few electron-hole pairs are produced thermally.

In the -type semiconductor the acceptor level lies just above ; most of the holes in the valence band are due to the acceptors.
(ii) Donor level: the extra electron of a donor atom sits in the level , only about 0.01 eV (Ge) to 0.05 eV (Si) below the conduction band. With this very small energy, available at room temperature, the electron moves into the conduction band. So the donor level supplies electrons to the conduction band, and electrons become the majority carriers.
Acceptor level: the level lies only about 0.01–0.05 eV above the valence band. An electron from the valence band easily jumps into it and ionises the acceptor, leaving a hole in the valence band. So the acceptor level takes electrons from the valence band, and holes become the majority carriers.
- 243 marks
Question 24
(I) Identify the circuit elements X and Y as shown in the given block diagram and draw the output waveforms of X and Y.

(II) If the centre tapping is shifted towards diode as shown in the diagram, draw the output waveform of the given circuit.
Solve with AIWritten solution
(I) X converts the ac into a unidirectional (pulsating) voltage, so X is a full-wave rectifier. Y smooths the pulsating output into a steady dc suitable for the appliance, so Y is a filter (for example, a capacitor across the load).
- Output of X: positive half-sine pulses, two in each input cycle.
- Output of Y: a nearly steady dc voltage close to the peak value, with a small ripple.
(II) When the centre tap is shifted towards , the part of the secondary between A and the tap becomes smaller than the part between the tap and B. now receives a smaller voltage than , so the output pulses are alternately smaller (due to ) and larger (due to ); both are still in the same direction.

- 253 marks
Question 25
(i) Draw the V-I characteristics of a - junction diode.
(ii) Differentiate between the threshold voltage and the breakdown voltage for a diode.
(iii) Write the property of a junction diode which makes it suitable for rectification of ac voltages.
Solve with AIWritten solution
(i) In forward bias the current is almost zero up to the threshold voltage and then rises steeply (mA). In reverse bias only a very small, nearly constant current (µA) flows until the breakdown voltage, where it suddenly increases.

(ii)
Threshold voltage Breakdown voltage It is a forward-bias voltage. It is a reverse-bias voltage. Beyond it the forward current increases sharply (about 0.7 V for Si, 0.2 V for Ge). At it the reverse current increases suddenly and sharply. The diode is normally operated above it in forward bias. A general-purpose diode is not operated at or beyond it; if the current is not limited the diode is destroyed. (iii) A junction diode has a low resistance in forward bias and a very high resistance in reverse bias, so it allows current to flow in one direction only. When an alternating voltage is applied, current flows only in the half-cycles in which the diode is forward biased, which rectifies the ac.
- 263 marks
Question 26
Explain the formation of potential barrier and depletion region in a - junction diode. What is the effect of applying forward bias on the width of the depletion region?
Solve with AIWritten solution
In the -region holes are the majority carriers, and in the -region electrons are the majority carriers. When the junction is formed, electrons diffuse from the -side to the -side and holes diffuse from the -side to the -side, because of the difference in concentration.
An electron leaving the -side leaves behind a positive donor ion, and a hole leaving the -side leaves behind a negative acceptor ion. These ions are fixed in the lattice. Near the junction a layer of positive ions builds up on the -side and a layer of negative ions on the -side, and this region has no free carriers: it is the depletion region.

The two layers of ions set up an electric field directed from the -side to the -side, and a potential difference across the junction, with the -side positive with respect to the -side. This opposes further diffusion of majority carriers and is called the potential barrier.
Effect of forward bias: the applied voltage opposes the barrier potential, so the effective barrier becomes and the width of the depletion region decreases.
- 273 marks
Question 27
(a) In the following diagram, is the junction diode forward biased or reverse biased?

(b) In the following diagram, which bulb out of and will glow and why?
Solve with AIWritten solution
(a) The -side of the diode is connected to earth (0 V), and its -side is connected through R to +5 V. The -side is at the lower potential, so the diode is reverse biased.
(b) The positive terminal of the 9 V battery is connected to the junction between the two diodes.
- : its -side is connected to the positive terminal and its -side goes towards , so it is forward biased and conducts.
- : its -side is connected to the positive terminal, so it is reverse biased and does not conduct.
So current flows through , and glows; does not glow.
- 283 marks
Question 28
A sinusoidal input voltage of peak value 12 V is applied across a network of 2 ideal diodes and 3 resistors as shown below.


Study the given network carefully. Considering the period when the positive half of the input voltage is fed into the network, answer the following questions.
(a) Identify which of the diodes would be conducting.
(b) Redraw an equivalent circuit diagram to show the flow of current and voltage drops across each of the circuit elements. Consider that ideal diodes offer zero resistance when forward biased and infinite resistance when reverse biased.
(c) Determine the output voltage across the 1 kΩ, 2 kΩ and 3 kΩ resistors respectively when the input voltage is at its maximum, V.
Solve with AIWritten solution
(a) In the positive half-cycle Q is at the higher potential and S at the lower.
- has its -side at Q and its -side at R, so it is forward biased and conducts.
- has its -side at Q, so it is reverse biased.
Only conducts.
(b) acts as a plain wire, so R is at the potential of Q; acts as an open switch, so the only connections of P are the 1 kΩ and 2 kΩ resistors.

Between R and S there are now two parallel paths: the 3 kΩ resistor directly, and the 1 kΩ and 2 kΩ resistors in series through P. Each path has the full input voltage across it.
(c) Across the 3 kΩ resistor:
The 1 kΩ + 2 kΩ path carries
So the voltages across 1 kΩ, 2 kΩ and 3 kΩ are 4 V, 8 V and 12 V.
- 293 marks
Question 29
(a) Name the device which utilises the unilateral action of a - diode to convert ac into dc.
(b) Draw the circuit diagram of a full-wave rectifier.
Solve with AIWritten solution
(a) The device is a rectifier. A diode conducts only when it is forward biased, so it passes current in one direction only and converts ac into a unidirectional (pulsating dc) current.
(b) A full-wave rectifier uses two diodes and a centre-tap transformer. The -sides of and go to the two ends A and B of the secondary; their -sides are joined, and the load is connected between this common point X and the centre tap.

In one half-cycle A is positive with respect to the centre tap and conducts; in the other half-cycle B is positive and conducts. In both half-cycles the current through flows in the same direction, from X to Y.
- 303 marks
Question 30
In a - junction diode, the forward bias resistance is low as compared to the reverse bias resistance. Give reason.
Solve with AIWritten solution
Forward bias: the applied voltage opposes the barrier potential, so the barrier is lowered to and the depletion layer narrows. A large number of majority carriers (holes from the -side, electrons from the -side) can then cross the junction, and a large current (mA) flows for a small voltage. The resistance is low.
Reverse bias: the applied voltage adds to the barrier, which rises to , and the depletion layer widens. Majority carriers cannot cross; only the few minority carriers are swept across, giving a very small current (µA) even for a large voltage. The resistance is very high.
- 315 marks
Question 31
(A) With the help of a circuit diagram, explain briefly how a - junction diode works as a half-wave rectifier.
(B) Give two differences between a half-wave rectifier and a full-wave rectifier.
Solve with AIWritten solution
(A) A rectifier converts ac into a unidirectional voltage. In a half-wave rectifier the secondary of a transformer supplies the ac voltage across A and B, and a diode D is connected in series with the load .

- Positive half-cycle: A is positive with respect to B, so the diode is forward biased. It conducts, and current flows through from X to Y, giving an output voltage.
- Negative half-cycle: A is negative, so the diode is reverse biased. It does not conduct (the tiny reverse current can be neglected), and the output is zero.

The output is a series of positive pulses, one in each cycle: unidirectional but varying.
(B)
Half-wave rectifier Full-wave rectifier Uses one diode. Uses two diodes (with a centre-tap transformer). Rectifies only one half of each ac cycle; the other half is lost. Rectifies both halves of each ac cycle. Output frequency equals the input frequency (50 Hz for 50 Hz input). Output frequency is twice the input frequency (100 Hz). - 325 marks
Question 32
(a) With the help of a labelled circuit diagram, explain the working of a - junction diode as a full-wave rectifier.
(b) Draw the input and output waveforms.
(c) What is the output frequency if the input ac frequency is 50 Hz?
Solve with AIWritten solution
(a) A full-wave rectifier uses two diodes and a centre-tap transformer. The ends A and B of the secondary are connected to the -sides of and , the -sides are joined at X, and the load is connected between X and the centre tap.

The voltages at A and B, measured from the centre tap, are always opposite in sign.
- When A is positive: B is negative. is forward biased and conducts; is reverse biased. Current flows through from X to Y.
- When A is negative: B is positive. conducts and does not. Current again flows through from X to Y.
So the current in the load is in the same direction during both halves of the cycle. Each diode rectifies only half of the total secondary voltage, but the two do so in alternate half-cycles.
(b)

Both halves of every input cycle appear as positive pulses in the output.
(c) There are two output pulses in every input cycle, so
- 335 marks
Question 33
(a) Draw the circuit arrangement for studying the V-I characteristics of a - junction diode in (i) forward bias and (ii) reverse bias.
(b) Why is a milliammeter used in one circuit and a microammeter in the other?
(c) Briefly explain how the typical V-I characteristics of a diode are obtained, and draw them.
Solve with AIWritten solution
(a) In both circuits a variable dc supply (a battery with a potentiometer or rheostat, drawn as a variable cell) is connected to the diode, so that the applied voltage can be varied; a voltmeter is connected across the diode and a current meter in series with it.

In the forward-bias circuit the -side is connected to the positive terminal; in the reverse-bias circuit the battery is reversed, so the -side is connected to the negative terminal.
(b) In forward bias the current is large, of the order of milliamperes, so a milliammeter is used. In reverse bias the current is very small, of the order of microamperes, so a microammeter is needed to measure it.
(c) The applied voltage is changed in small steps with the rheostat, and for each value the voltage across the diode and the current through it are noted. Plotting current against voltage for both biases gives the characteristic.

In forward bias the current stays very small until the threshold voltage (about 0.7 V for Si, 0.2 V for Ge) and then increases steeply. In reverse bias the current is very small and almost constant until the breakdown voltage, where it rises suddenly.
- 345 marks
Question 34
(a) Name the two important processes involved in the formation of a - junction.
(b) What is meant by minority carrier injection in a forward-biased - junction? How does it give rise to the forward current?
(c) Why is the current in a reverse-biased junction very small and almost independent of the applied voltage (below breakdown)?
Solve with AIWritten solution
(a) Diffusion of majority carriers across the junction (holes from to , electrons from to ) and drift of carriers under the electric field of the depletion region, which opposes the diffusion. The junction is in equilibrium when the two currents are equal.

(b) In forward bias the barrier is lowered to , so electrons from the -side cross into the -side, where they are minority carriers, and holes from the -side cross into the -side, where they too are minority carriers. This is minority carrier injection.
Near each edge of the junction the concentration of these injected minority carriers becomes much larger than far away from the junction. Because of this concentration gradient the injected electrons diffuse through the -side and the injected holes diffuse through the -side. The sum of the hole-diffusion current and the electron-diffusion current is the forward current, of the order of mA.
(c) In reverse bias the barrier rises to and majority carriers cannot cross. The only current is the drift of minority carriers (electrons on the -side, holes on the -side) that reach the junction and are swept across by the field. There are very few minority carriers, so the current is only of the order of µA.
Even a small reverse voltage is enough to sweep across every minority carrier that arrives at the junction, so making the voltage larger does not increase the current: the current is limited by the number of minority carriers, which is set by the temperature, not by the applied voltage.
- 352 marks
Question 35
In an -type semiconductor, electron-hole recombination is a continuous process at room temperature. Yet the electron concentration is always greater than the hole concentration in it. Explain.
Solve with AIWritten solution
In an -type semiconductor the free electrons come from two sources: the donor atoms (each pentavalent dopant gives one electron) and the thermal generation of electron-hole pairs in the host crystal. The holes, however, come only from the thermal (intrinsic) source.
Recombination removes electrons and holes in equal numbers, one of each at a time. It therefore cannot make up the difference between them: the extra electrons supplied by the donors always remain. In fact, with so many electrons present, the holes recombine more often and their number falls even below the intrinsic value. So always stays much greater than ().
- 361 mark
Question 36
Assertion (A): The resistance of an intrinsic semiconductor decreases with increase in its temperature.
Reason (R): The number of conduction electrons as well as holes increases in an intrinsic semiconductor with rise in its temperature.
Solve with AIAnswer
- Correct
(A) Both Assertion (A) and Reason (R) are true, and Reason (R) is the correct explanation of Assertion (A).
(B) Both Assertion (A) and Reason (R) are true, but Reason (R) is not the correct explanation of Assertion (A).
(C) Assertion (A) is true, but Reason (R) is false.
(D) Assertion (A) is false, and Reason (R) is also false.
Option (A) is correct.
Explanation: In an intrinsic semiconductor the carriers are produced by thermal energy breaking covalent bonds. As the temperature rises, more bonds break, so the numbers of free electrons and holes both increase (the Reason is true). With more carriers available the material conducts better, so its resistance decreases (the Assertion is true). The increase in the number of carriers is exactly why the resistance falls, so the Reason explains the Assertion.
- 371 mark
Question 37
Assertion (A): In insulators, the forbidden gap is very large.
Reason (R): The valence electrons in an atom of an insulator are very tightly bound to the nucleus.
Solve with AIAnswer
- Correct
(A) Both Assertion (A) and Reason (R) are true, and Reason (R) is the correct explanation of Assertion (A).
(B) Both Assertion (A) and Reason (R) are true, but Reason (R) is not the correct explanation of Assertion (A).
(C) Assertion (A) is true, but Reason (R) is false.
(D) Assertion (A) is false, and Reason (R) is also false.
Option (A) is correct.
Explanation: For insulators the forbidden gap is more than 3 eV, which is very large (the Assertion is true; for diamond it is 5.4 eV). Their valence electrons are held very tightly, so a large energy is needed to free one and lift it into the conduction band (the Reason is true). This tight binding is what makes the gap large, so the Reason explains the Assertion. For comparison, the valence electrons of Si and Ge lie in outer orbits, are held less tightly, and have gaps of only 1.1 eV and 0.7 eV.
