Confirming your payment

Skip to content

Opening your dashboard

Class 11 Physics Chapter 8: Mechanical Properties Of Solids Solutions

16 textbook questions with step-by-step answers, free to read, for CBSE 2026-27.

AI Tutor

Get talked through Ch 8, not just shown the answer

Reading a finished solution is not the same as being able to do it. The AI tutor takes one question at a time and works it with you, in your own words, until you can.

  • Ask it out loud, in your own words
  • It gives you the next step, not the answer
  • Stuck on part (ii)? Start there
Ch 8 solutions

16 questions with solutions

2–5 marks · Medium difficulty

  1. 1

    Question 1

    A steel wire of length 4.7 m and cross-sectional area 3.0×10−5 m23.0 \times 10^{-5}\ \text{m}^2 stretches by the same amount as a copper wire of length 3.5 m and cross-sectional area of 4.0×10−5 m24.0 \times 10^{-5}\ \text{m}^2 under a given load. What is the ratio of the Young's modulus of steel to that of copper?

    Medium
    3 marks
    Solve with AI
    Written solution

    Let the same load FF produce the same extension ΔL\Delta L in both wires. From

    Y=FLA ΔLY = \frac{F L}{A\, \Delta L}

    Steel: Ls=4.7 mL_s = 4.7\ \text{m}, As=3.0×10−5 m2A_s = 3.0 \times 10^{-5}\ \text{m}^2, so

    Ys=F×4.73.0×10−5×ΔLY_s = \frac{F \times 4.7}{3.0 \times 10^{-5} \times \Delta L}

    Copper: Lc=3.5 mL_c = 3.5\ \text{m}, Ac=4.0×10−5 m2A_c = 4.0 \times 10^{-5}\ \text{m}^2, so

    Yc=F×3.54.0×10−5×ΔLY_c = \frac{F \times 3.5}{4.0 \times 10^{-5} \times \Delta L}

    Dividing, FF and ΔL\Delta L cancel:

    YsYc=LsLc×AcAs=4.73.5×4.0×10−53.0×10−5=18.810.5\frac{Y_s}{Y_c} = \frac{L_s}{L_c} \times \frac{A_c}{A_s} = \frac{4.7}{3.5} \times \frac{4.0 \times 10^{-5}}{3.0 \times 10^{-5}} = \frac{18.8}{10.5} YsYc=1.79\frac{Y_s}{Y_c} = 1.79

    The Young's modulus of steel is 1.79 times that of copper. (This agrees with Table 8.1: 200 GPa/110 GPa≈1.8200\ \text{GPa} / 110\ \text{GPa} \approx 1.8.)

  2. 2

    Question 2

    Figure 8.9 shows the strain-stress curve for a given material. What are

    (a) Young's modulus and

    (b) approximate yield strength for this material?

    Class 11 Physics Mechanical Properties Of Solids

    Medium
    4 marks
    Solve with AI
    Written solution

    (a) Young's modulus

    In the straight-line (proportional) part of the curve, Young's modulus is the slope, stress/strain. Take any point on the straight line, for example strain =0.002= 0.002 where the stress is 150×106 N m−2150 \times 10^{6}\ \text{N m}^{-2}:

    Y=stressstrain=150×106 N m−20.002Y = \frac{\text{stress}}{\text{strain}} = \frac{150 \times 10^{6}\ \text{N m}^{-2}}{0.002} Y=7.5×1010 N m−2Y = 7.5 \times 10^{10}\ \text{N m}^{-2}

    Young's modulus =7.5×1010 N m−2= 7.5 \times 10^{10}\ \text{N m}^{-2}.

    (b) Yield strength

    The yield strength σy\sigma_y is the stress at the yield point (elastic limit): up to this stress the material returns to its original length when the load is removed; beyond it the deformation becomes permanent. (It is not the largest stress the material can bear, which is the ultimate strength.)

    On this graph the curve stays a straight line almost up to the top and bends over only at a stress of about 300×106 N m−2300 \times 10^{6}\ \text{N m}^{-2}. So

    σy≈300×106 N m−2\sigma_y \approx 300 \times 10^{6}\ \text{N m}^{-2}

    Approximate yield strength ≈3×108 N m−2\approx 3 \times 10^{8}\ \text{N m}^{-2}.

    Class 11 Physics Mechanical Properties Of Solids

  3. 3

    Question 3

    The stress-strain graphs for materials A and B are shown in Fig. 8.10.

    Class 11 Physics Mechanical Properties Of Solids

    The graphs are drawn to the same scale.

    (a) Which of the materials has the greater Young's modulus?

    (b) Which of the two is the stronger material?

    Medium
    3 marks
    Solve with AI
    Written solution

    (a) Material A. Young's modulus is the slope (stress/strain) of the initial straight part of the stress-strain graph. Since both graphs are drawn to the same scale, compare the slopes directly: A's initial straight line is much steeper than B's. For the same strain, A develops a larger stress, so

    YA>YBY_A > Y_B

    Material A has the greater Young's modulus.

    (b) Material A. The strength of a material is measured by the stress it can bear before it fractures. A's curve reaches a higher stress than B's before fracture, so A is the stronger material. (A also bears far more strain before breaking, which shows it is more ductile; that is a separate property from strength.)

    Material A is the stronger material.

  4. 4

    Question 4

    Read the following two statements below carefully and state, with reasons, if it is true or false:

    (a) The Young's modulus of rubber is greater than that of steel;

    (b) The stretching of a coil is determined by its shear modulus.

    Medium
    3 marks
    Solve with AI
    Written solution

    (a) False. Young's modulus is

    Y=stresslongitudinal strainY = \frac{\text{stress}}{\text{longitudinal strain}}

    For the same stress, a rubber cord stretches far more than a steel wire, that is, rubber shows a much larger strain. So YY for rubber is much smaller than for steel (steel: 2.0×1011 N m−22.0 \times 10^{11}\ \text{N m}^{-2}, Table 8.1; rubber is an elastomer with a very small YY). In physics, the material that stretches less for a given load is the more elastic one, so steel is more elastic than rubber.

    (b) True. When a coil (helical spring) is stretched, the length of the wire itself hardly changes. Instead, the coils open out and the wire of each turn is sheared: it changes its shape without any appreciable change in length or volume. A change of shape is a shearing strain, so the amount by which the coil stretches for a given load is governed by the shear modulus of the material of the wire.

  5. 5

    Question 5

    Two wires of diameter 0.25 cm, one made of steel and the other made of brass are loaded as shown in Fig. 8.11. The unloaded length of steel wire is 1.5 m and that of brass wire is 1.0 m. Compute the elongations of the steel and the brass wires.

    Class 11 Physics Mechanical Properties Of Solids

    Medium
    5 marks
    Solve with AI
    Written solution

    Tension in each wire. The brass wire holds only the 6.0 kg mass. The steel wire holds the 4.0 kg mass and everything hanging below it (brass wire and 6.0 kg mass; the wires are light). With g=9.8 m s−2g = 9.8\ \text{m s}^{-2}:

    Tsteel=(4.0+6.0)×9.8=98 NT_{\text{steel}} = (4.0 + 6.0) \times 9.8 = 98\ \text{N} Tbrass=6.0×9.8=58.8 NT_{\text{brass}} = 6.0 \times 9.8 = 58.8\ \text{N}

    Class 11 Physics Mechanical Properties Of Solids

    Cross-sectional area (same for both wires): r=0.25 cm2=1.25×10−3 mr = \dfrac{0.25\ \text{cm}}{2} = 1.25 \times 10^{-3}\ \text{m}

    A=πr2=π×(1.25×10−3)2=4.91×10−6 m2A = \pi r^2 = \pi \times (1.25 \times 10^{-3})^2 = 4.91 \times 10^{-6}\ \text{m}^2

    Moduli: Ysteel=2.0×1011 PaY_{\text{steel}} = 2.0 \times 10^{11}\ \text{Pa} (Table 8.1). Brass is not listed in Table 8.1; we take Ybrass=0.91×1011 PaY_{\text{brass}} = 0.91 \times 10^{11}\ \text{Pa}.

    The elongation is ΔL=TLAY\Delta L = \dfrac{T L}{A Y}.

    Steel wire (L=1.5 mL = 1.5\ \text{m}):

    ΔLsteel=98×1.54.91×10−6×2.0×1011=1479.82×105\Delta L_{\text{steel}} = \frac{98 \times 1.5}{4.91 \times 10^{-6} \times 2.0 \times 10^{11}} = \frac{147}{9.82 \times 10^{5}} ΔLsteel=1.50×10−4 m\Delta L_{\text{steel}} = 1.50 \times 10^{-4}\ \text{m}

    Brass wire (L=1.0 mL = 1.0\ \text{m}):

    ΔLbrass=58.8×1.04.91×10−6×0.91×1011=58.84.47×105\Delta L_{\text{brass}} = \frac{58.8 \times 1.0}{4.91 \times 10^{-6} \times 0.91 \times 10^{11}} = \frac{58.8}{4.47 \times 10^{5}} ΔLbrass=1.3×10−4 m\Delta L_{\text{brass}} = 1.3 \times 10^{-4}\ \text{m}

    Elongation of the steel wire ≈1.5×10−4 m\approx 1.5 \times 10^{-4}\ \text{m}; elongation of the brass wire ≈1.3×10−4 m\approx 1.3 \times 10^{-4}\ \text{m}.

  6. 6

    Question 6

    The edge of an aluminium cube is 10 cm long. One face of the cube is firmly fixed to a vertical wall. A mass of 100 kg is then attached to the opposite face of the cube. The shear modulus of aluminium is 25 GPa. What is the vertical deflection of this face?

    Class 11 Physics Mechanical Properties Of Solids

    Medium
    5 marks
    Solve with AI
    Written solution

    The weight of the mass acts vertically downward on the free face, that is, parallel to that face. Its reaction at the fixed face is equal and opposite. This is a shearing stress, so the free face slides down relative to the fixed face.

    Class 11 Physics Mechanical Properties Of Solids

    Data: L=10 cm=0.10 mL = 10\ \text{cm} = 0.10\ \text{m}, area of a face A=L2=(0.10)2=1.0×10−2 m2A = L^2 = (0.10)^2 = 1.0 \times 10^{-2}\ \text{m}^2, G=25 GPa=25×109 N m−2G = 25\ \text{GPa} = 25 \times 10^{9}\ \text{N m}^{-2}

    Shearing force:

    F=mg=100×9.8=980 NF = mg = 100 \times 9.8 = 980\ \text{N}

    Shearing strain. From G=F/AθG = \dfrac{F/A}{\theta},

    θ=FAG=9801.0×10−2×25×109=3.92×10−6\theta = \frac{F}{A G} = \frac{980}{1.0 \times 10^{-2} \times 25 \times 10^{9}} = 3.92 \times 10^{-6}

    Deflection. The shearing strain is θ=ΔxL\theta = \dfrac{\Delta x}{L}, so

    Δx=θL=3.92×10−6×0.10=3.92×10−7 m\Delta x = \theta L = 3.92 \times 10^{-6} \times 0.10 = 3.92 \times 10^{-7}\ \text{m}

    The vertical deflection of the face is 3.92×10−7 m3.92 \times 10^{-7}\ \text{m} (≈4×10−7 m\approx 4 \times 10^{-7}\ \text{m}).

  7. 7

    Question 7

    Four identical hollow cylindrical columns of mild steel support a big structure of mass 50,000 kg. The inner and outer radii of each column are 30 and 60 cm respectively. Assuming the load distribution to be uniform, calculate the compressional strain of each column.

    Medium
    4 marks
    Solve with AI
    Written solution

    Load on each column. The weight is shared equally by the four columns:

    F=Mg4=50000×9.84=1.225×105 NF = \frac{Mg}{4} = \frac{50000 \times 9.8}{4} = 1.225 \times 10^{5}\ \text{N}

    Area that carries the load. Only the ring of metal between r1=0.30 mr_1 = 0.30\ \text{m} and r2=0.60 mr_2 = 0.60\ \text{m} carries the load:

    Class 11 Physics Mechanical Properties Of Solids

    A=π(r22−r12)=π(0.36−0.09)=0.27π=0.848 m2A = \pi (r_2^2 - r_1^2) = \pi (0.36 - 0.09) = 0.27\pi = 0.848\ \text{m}^2

    Compressive stress:

    σ=FA=1.225×1050.848=1.44×105 N m−2\sigma = \frac{F}{A} = \frac{1.225 \times 10^{5}}{0.848} = 1.44 \times 10^{5}\ \text{N m}^{-2}

    Compressional strain. For mild steel Y=2.0×1011 N m−2Y = 2.0 \times 10^{11}\ \text{N m}^{-2} (Table 8.1), and YY is the same for compression as for tension:

    strain=σY=1.44×1052.0×1011\text{strain} = \frac{\sigma}{Y} = \frac{1.44 \times 10^{5}}{2.0 \times 10^{11}} strain=7.22×10−7\text{strain} = 7.22 \times 10^{-7}

    The compressional strain of each column is 7.22×10−77.22 \times 10^{-7}.

  8. 8

    Question 8

    A piece of copper having a rectangular cross-section of 15.2 mm × 19.1 mm is pulled in tension with 44,500 N force, producing only elastic deformation. Calculate the resulting strain?

    Medium
    3 marks
    Solve with AI
    Written solution

    The copper is pulled in tension: the force acts perpendicular to the cross-section and produces a change in length, so the relevant modulus is Young's modulus, YCu=110 GPa=1.1×1011 N m−2Y_{\text{Cu}} = 110\ \text{GPa} = 1.1 \times 10^{11}\ \text{N m}^{-2} (Table 8.1). (Using the shear modulus of copper, 42 GPa, would give 3.65×10−33.65 \times 10^{-3}, which is wrong because there is no shearing force here.)

    Area:

    A=15.2 mm×19.1 mm=290.3 mm2=2.903×10−4 m2A = 15.2\ \text{mm} \times 19.1\ \text{mm} = 290.3\ \text{mm}^2 = 2.903 \times 10^{-4}\ \text{m}^2

    Tensile stress:

    σ=FA=445002.903×10−4=1.53×108 N m−2\sigma = \frac{F}{A} = \frac{44500}{2.903 \times 10^{-4}} = 1.53 \times 10^{8}\ \text{N m}^{-2}

    Strain:

    strain=σY=1.53×1081.1×1011\text{strain} = \frac{\sigma}{Y} = \frac{1.53 \times 10^{8}}{1.1 \times 10^{11}} strain=1.39×10−3\text{strain} = 1.39 \times 10^{-3}

    The resulting (tensile) strain is 1.39×10−31.39 \times 10^{-3}.

  9. 9

    Question 9

    A steel cable with a radius of 1.5 cm supports a chairlift at a ski area. If the maximum stress is not to exceed 108 N m−210^{8}\ \text{N m}^{-2}, what is the maximum load the cable can support?

    Medium
    2 marks
    Solve with AI
    Written solution

    Cross-sectional area: r=1.5 cm=1.5×10−2 mr = 1.5\ \text{cm} = 1.5 \times 10^{-2}\ \text{m}

    A=πr2=π×(1.5×10−2)2=7.07×10−4 m2A = \pi r^2 = \pi \times (1.5 \times 10^{-2})^2 = 7.07 \times 10^{-4}\ \text{m}^2

    Maximum load. Since stress =F/A= F/A, the largest force the cable may carry is

    Fmax⁡=σmax⁡×A=108×7.07×10−4F_{\max} = \sigma_{\max} \times A = 10^{8} \times 7.07 \times 10^{-4} Fmax⁡=7.07×104 NF_{\max} = 7.07 \times 10^{4}\ \text{N}

    The cable can support a maximum load of 7.07×104 N7.07 \times 10^{4}\ \text{N}.

  10. 10

    Question 10

    A rigid bar of mass 15 kg is supported symmetrically by three wires each 2.0 m long. Those at each end are of copper and the middle one is of iron. Determine the ratios of their diameters if each is to have the same tension.

    Medium
    3 marks
    Solve with AI
    Written solution

    Class 11 Physics Mechanical Properties Of Solids

    Same tension. Each wire carries T=15×9.83=49 NT = \dfrac{15 \times 9.8}{3} = 49\ \text{N}.

    Same strain. The bar is rigid and hangs level, so all three wires stretch by the same amount ΔL\Delta L. As they also have the same length L=2.0 mL = 2.0\ \text{m}, the strain ΔL/L\Delta L/L is the same in each.

    Relating diameter to YY. For a wire of diameter DD,

    Y=T/AΔL/L=4TπD2×LΔLY = \frac{T/A}{\Delta L/L} = \frac{4T}{\pi D^2} \times \frac{L}{\Delta L}

    With TT, LL and ΔL\Delta L the same for all wires,

    YD2=constant⇒D∝1YY D^2 = \text{constant} \quad \Rightarrow \quad D \propto \frac{1}{\sqrt{Y}}

    Ratio. Using YCu=110 GPaY_{\text{Cu}} = 110\ \text{GPa} and YFe=190 GPaY_{\text{Fe}} = 190\ \text{GPa} (Table 8.1),

    DCuDFe=YFeYCu=190110=1.727\frac{D_{\text{Cu}}}{D_{\text{Fe}}} = \sqrt{\frac{Y_{\text{Fe}}}{Y_{\text{Cu}}}} = \sqrt{\frac{190}{110}} = \sqrt{1.727} DCuDFe=1.31\frac{D_{\text{Cu}}}{D_{\text{Fe}}} = 1.31

    The diameters of the copper and iron wires must be in the ratio DCu:DFe=1.31:1D_{\text{Cu}} : D_{\text{Fe}} = 1.31 : 1. (The copper wires are thicker, since copper has the smaller Young's modulus.)

  11. 11

    Question 11

    A 14.5 kg mass, fastened to the end of a steel wire of unstretched length 1.0 m, is whirled in a vertical circle with an angular velocity of 2 rev/s at the bottom of the circle. The cross-sectional area of the wire is 0.065 cm20.065\ \text{cm}^2. Calculate the elongation of the wire when the mass is at the lowest point of its path.

    Medium
    4 marks
    Solve with AI
    Written solution

    Data: m=14.5 kgm = 14.5\ \text{kg}, radius of the circle r=L=1.0 mr = L = 1.0\ \text{m} (the tiny stretch is neglected), A=0.065 cm2=6.5×10−6 m2A = 0.065\ \text{cm}^2 = 6.5 \times 10^{-6}\ \text{m}^2, Ysteel=2.0×1011 N m−2Y_{\text{steel}} = 2.0 \times 10^{11}\ \text{N m}^{-2} (Table 8.1).

    Angular velocity:

    ω=2 rev s−1=2×2π=4π rad s−1=12.57 rad s−1\omega = 2\ \text{rev s}^{-1} = 2 \times 2\pi = 4\pi\ \text{rad s}^{-1} = 12.57\ \text{rad s}^{-1}

    Tension at the lowest point. Two forces act on the mass: the tension TT upward (towards the centre O) and its weight mgmg downward. Their resultant provides the centripetal force mω2rm\omega^2 r towards O:

    Class 11 Physics Mechanical Properties Of Solids

    T−mg=mω2rT - mg = m \omega^2 r T=m(g+ω2r)=14.5×(9.8+16π2×1.0)=14.5×(9.8+157.9)T = m(g + \omega^2 r) = 14.5 \times (9.8 + 16\pi^2 \times 1.0) = 14.5 \times (9.8 + 157.9) T=142.1+2289.7=2431.8 NT = 142.1 + 2289.7 = 2431.8\ \text{N}

    Elongation:

    ΔL=TLAY=2431.8×1.06.5×10−6×2.0×1011=2431.81.3×106\Delta L = \frac{T L}{A Y} = \frac{2431.8 \times 1.0}{6.5 \times 10^{-6} \times 2.0 \times 10^{11}} = \frac{2431.8}{1.3 \times 10^{6}} ΔL=1.87×10−3 m\Delta L = 1.87 \times 10^{-3}\ \text{m}

    The elongation of the wire at the lowest point is 1.87×10−3 m1.87 \times 10^{-3}\ \text{m} (about 1.9 mm).

  12. 12

    Question 12

    Compute the bulk modulus of water from the following data: Initial volume = 100.0 litre, Pressure increase = 100.0 atm (1 atm=1.013×105 Pa1\ \text{atm} = 1.013 \times 10^{5}\ \text{Pa}), Final volume = 100.5 litre. Compare the bulk modulus of water with that of air (at constant temperature). Explain in simple terms why the ratio is so large.

    Medium
    4 marks
    Solve with AI
    Written solution

    A note on the data. An increase in pressure always decreases the volume, so the final volume should be 99.5 litre, not 100.5 litre (a misprint in the book). The magnitude of the volume change is what matters:

    ∣ΔV∣=100.0−99.5=0.5 litre=0.5×10−3 m3\lvert \Delta V \rvert = 100.0 - 99.5 = 0.5\ \text{litre} = 0.5 \times 10^{-3}\ \text{m}^3

    Data: V=100.0 litre=100.0×10−3 m3V = 100.0\ \text{litre} = 100.0 \times 10^{-3}\ \text{m}^3,

    p=100.0 atm=100.0×1.013×105=1.013×107 Pap = 100.0\ \text{atm} = 100.0 \times 1.013 \times 10^{5} = 1.013 \times 10^{7}\ \text{Pa}

    Bulk modulus of water. From B=−pΔV/VB = -\dfrac{p}{\Delta V / V} (the minus sign makes BB positive, since ΔV\Delta V is negative),

    B=pV∣ΔV∣=1.013×107×100.0×10−30.5×10−3B = \frac{p V}{\lvert \Delta V \rvert} = \frac{1.013 \times 10^{7} \times 100.0 \times 10^{-3}}{0.5 \times 10^{-3}} Bwater=2.026×109 Pa≈2.0×109 PaB_{\text{water}} = 2.026 \times 10^{9}\ \text{Pa} \approx 2.0 \times 10^{9}\ \text{Pa}

    Comparison with air. At constant temperature, Bair=1.0×105 PaB_{\text{air}} = 1.0 \times 10^{5}\ \text{Pa} (Table 8.3). So

    BwaterBair=2.026×1091.0×105=2.0×104\frac{B_{\text{water}}}{B_{\text{air}}} = \frac{2.026 \times 10^{9}}{1.0 \times 10^{5}} = 2.0 \times 10^{4}

    Bulk modulus of water ≈2.0×109 Pa\approx 2.0 \times 10^{9}\ \text{Pa}, about 2×1042 \times 10^{4} times that of air.

    Why the ratio is so large. In a liquid the molecules are packed closely together, and the intermolecular forces are strong; squeezing them even slightly closer needs a very large pressure, so a liquid is hard to compress (large BB). In a gas the molecules are far apart and the forces between them are very weak, so the same pressure reduces the volume of air enormously (small BB). For the same pressure, the volume strain of air is about 2×1042 \times 10^{4} times that of water.

  13. 13

    Question 13

    What is the density of water at a depth where pressure is 80.0 atm, given that its density at the surface is 1.03×103 kg m−31.03 \times 10^{3}\ \text{kg m}^{-3}?

    Medium
    3 marks
    Solve with AI
    Written solution

    Increase in pressure. At the surface the pressure is 1.0 atm, so

    Δp=80.0−1.0=79.0 atm=79.0×1.013×105=8.00×106 Pa\Delta p = 80.0 - 1.0 = 79.0\ \text{atm} = 79.0 \times 1.013 \times 10^{5} = 8.00 \times 10^{6}\ \text{Pa}

    Volume strain. With Bwater=2.2×109 PaB_{\text{water}} = 2.2 \times 10^{9}\ \text{Pa} (Table 8.3),

    ∣ΔV∣V=ΔpB=8.00×1062.2×109=3.64×10−3\frac{\lvert \Delta V \rvert}{V} = \frac{\Delta p}{B} = \frac{8.00 \times 10^{6}}{2.2 \times 10^{9}} = 3.64 \times 10^{-3}

    (Equivalently, the compressibility of water is k=1/B=4.5×10−10 Pa−1k = 1/B = 4.5 \times 10^{-10}\ \text{Pa}^{-1}, and k Δpk\,\Delta p gives the same volume strain.)

    Density. A given mass MM of water has volume V=M/ρV = M/\rho at the surface and V′=V−∣ΔV∣V' = V - \lvert \Delta V \rvert at the depth. Since the mass is unchanged,

    ρ′=MV′=MV(1−∣ΔV∣V)=ρ1−∣ΔV∣V\rho' = \frac{M}{V'} = \frac{M}{V\left(1 - \dfrac{\lvert \Delta V \rvert}{V}\right)} = \frac{\rho}{1 - \dfrac{\lvert \Delta V \rvert}{V}} ρ′=1.03×1031−3.64×10−3=1.03×1030.99636\rho' = \frac{1.03 \times 10^{3}}{1 - 3.64 \times 10^{-3}} = \frac{1.03 \times 10^{3}}{0.99636} ρ′=1.034×103 kg m−3\rho' = 1.034 \times 10^{3}\ \text{kg m}^{-3}

    The density of water at that depth is about 1.034×103 kg m−31.034 \times 10^{3}\ \text{kg m}^{-3}, only about 0.36 % more than at the surface, because water is nearly incompressible.

  14. 14

    Question 14

    Compute the fractional change in volume of a glass slab, when subjected to a hydraulic pressure of 10 atm.

    Medium
    3 marks
    Solve with AI
    Written solution

    Data: p=10 atm=10×1.013×105=1.013×106 Pap = 10\ \text{atm} = 10 \times 1.013 \times 10^{5} = 1.013 \times 10^{6}\ \text{Pa}; bulk modulus of glass B=37 GPa=37×109 PaB = 37\ \text{GPa} = 37 \times 10^{9}\ \text{Pa} (Table 8.3).

    From B=−pΔV/VB = -\dfrac{p}{\Delta V / V}, the magnitude of the fractional change in volume is

    ∣ΔV∣V=pB=1.013×10637×109\frac{\lvert \Delta V \rvert}{V} = \frac{p}{B} = \frac{1.013 \times 10^{6}}{37 \times 10^{9}} ∣ΔV∣V=2.74×10−5\frac{\lvert \Delta V \rvert}{V} = 2.74 \times 10^{-5}

    The volume of the glass slab decreases by a fraction 2.74×10−52.74 \times 10^{-5} (about 0.0027 %).

  15. 15

    Question 15

    Determine the volume contraction of a solid copper cube, 10 cm on an edge, when subjected to a hydraulic pressure of 7.0×106 Pa7.0 \times 10^{6}\ \text{Pa}.

    Medium
    3 marks
    Solve with AI
    Written solution

    Data: edge a=10 cm=0.10 ma = 10\ \text{cm} = 0.10\ \text{m}, so

    V=a3=(0.10)3=1.0×10−3 m3V = a^3 = (0.10)^3 = 1.0 \times 10^{-3}\ \text{m}^3

    p=7.0×106 Pap = 7.0 \times 10^{6}\ \text{Pa}; bulk modulus of copper B=140 GPa=1.4×1011 PaB = 140\ \text{GPa} = 1.4 \times 10^{11}\ \text{Pa} (Table 8.3).

    From B=−pΔV/VB = -\dfrac{p}{\Delta V / V}, the contraction in volume is

    ∣ΔV∣=pVB=7.0×106×1.0×10−31.4×1011\lvert \Delta V \rvert = \frac{p V}{B} = \frac{7.0 \times 10^{6} \times 1.0 \times 10^{-3}}{1.4 \times 10^{11}} ∣ΔV∣=5.0×10−8 m3=5.0×10−2 cm3\lvert \Delta V \rvert = 5.0 \times 10^{-8}\ \text{m}^3 = 5.0 \times 10^{-2}\ \text{cm}^3

    The volume of the cube decreases by 5.0×10−2 cm35.0 \times 10^{-2}\ \text{cm}^3.

  16. 16

    Question 16

    How much should the pressure on a litre of water be changed to compress it by 0.10%?

    Medium
    3 marks
    Solve with AI
    Written solution

    Data: V=1 litre=1.0×10−3 m3V = 1\ \text{litre} = 1.0 \times 10^{-3}\ \text{m}^3; the volume is to decrease by 0.10 %, so

    ∣ΔV∣V=0.10100=1.0×10−3\frac{\lvert \Delta V \rvert}{V} = \frac{0.10}{100} = 1.0 \times 10^{-3}

    (that is, ∣ΔV∣=1.0×10−6 m3=1 cm3\lvert \Delta V \rvert = 1.0 \times 10^{-6}\ \text{m}^3 = 1\ \text{cm}^3). Bulk modulus of water B=2.2×109 PaB = 2.2 \times 10^{9}\ \text{Pa} (Table 8.3).

    From B=−ΔpΔV/VB = -\dfrac{\Delta p}{\Delta V / V},

    Δp=B×∣ΔV∣V=2.2×109×1.0×10−3\Delta p = B \times \frac{\lvert \Delta V \rvert}{V} = 2.2 \times 10^{9} \times 1.0 \times 10^{-3} Δp=2.2×106 Pa\Delta p = 2.2 \times 10^{6}\ \text{Pa}

    The pressure must be increased by 2.2×106 Pa2.2 \times 10^{6}\ \text{Pa}, which is about 2.2×1061.013×105≈22 atm\dfrac{2.2 \times 10^{6}}{1.013 \times 10^{5}} \approx 22\ \text{atm}.

Inside Ch 8

What Class 11 Physics Ch 8 covers

The sections of the chapter, in the order the book takes them. Every question above comes from one of these.

  1. 01Inter Molecular Force
  2. 02Hooke’s law
  3. 03Stress-Strain Curve
  4. 04Modulus Of Elasticity
  5. 05Applications Of Elastic Behaviour Of Materials
Common questions

Class 11 Physics Ch 8 questions students ask

How many questions are there in Class 11 Physics Ch 8?

16 questions. Every one is solved step by step on this page.

Are these Class 11 Physics solutions free?

Yes. Every question and its full working is free to read, with no account needed.

Can I download the Class 11 Physics Ch 8 solutions as a PDF?

There is no PDF to download. Every solution is on this page instead, which means it is searchable, always the current syllabus, and readable on a phone. Use your browser's print option if you want it on paper.