Confirming your payment

Skip to content

Opening your dashboard

Class 11 Physics Chapter 9: Mechanical Properties Of Fluids Solutions

20 textbook questions with step-by-step answers, free to read, for CBSE 2026-27.

AI Tutor

Get talked through Ch 9, not just shown the answer

Reading a finished solution is not the same as being able to do it. The AI tutor takes one question at a time and works it with you, in your own words, until you can.

  • Ask it out loud, in your own words
  • It gives you the next step, not the answer
  • Stuck on part (ii)? Start there
Ch 9 solutions

20 questions with solutions

2–4 marks · Medium difficulty

  1. 1

    Question 1

    Explain why

    (a) The blood pressure in humans is greater at the feet than at the brain.

    (b) Atmospheric pressure at a height of about 6 km decreases to nearly half of its value at the sea level, though the height of the atmosphere is more than 100 km.

    (c) Hydrostatic pressure is a scalar quantity even though pressure is force divided by area.

    Medium
    3 marks
    Solve with AI
    Written solution

    (a) Blood is a liquid, and the pressure in a liquid increases with depth. For two points in a liquid column separated by a vertical height hh,

    P2−P1=ρghP_2 - P_1 = \rho g h

    In a standing person the feet are much farther below the heart than the brain is above it. The column of blood between the heart and the feet is therefore much taller than the column between the heart and the brain, so the extra pressure ρgh\rho g h is much larger at the feet. Hence the blood pressure is greater at the feet than at the brain.

    (b) The pressure at any height is the weight, per unit area, of all the air above that height. Air is highly compressible: the air near the ground is squeezed by the weight of the air above it, so its density is largest near the ground and falls off rapidly with height. As a result most of the mass of the atmosphere is packed into the lowest few kilometres, and the thin air between about 10 km and 100 km, though it fills by far the largest volume, makes up only about a quarter of the total mass.

    So by a height of about 6 km roughly half of the atmosphere's mass is already below us, and the weight of the air column above, that is the pressure, has fallen to nearly half its sea-level value, even though the atmosphere extends to more than 100 km. (If air had the same density at all heights, the pressure would fall uniformly with height and would halve only at half the total height.)

    (c) In the definition P=F/AP = F/A, the force FF is the component of force normal to the area. At a given point in a fluid at rest, the pressure is the same in all directions (Pascal's law): a small surface placed at that point experiences the same force per unit area whichever way it faces, and that force is always perpendicular to the surface.

    Since the pressure at a point has the same value for every orientation, no particular direction can be associated with it. The direction of the force comes from the orientation of the surface, not from the pressure. Pressure therefore has magnitude only and is a scalar quantity.

  2. 2

    Question 2

    Explain why

    (a) The angle of contact of mercury with glass is obtuse, while that of water with glass is acute.

    (b) Water on a clean glass surface tends to spread out while mercury on the same surface tends to form drops. (Put differently, water wets glass while mercury does not.)

    (c) Surface tension of a liquid is independent of the area of the surface.

    (d) Water with detergent dissolved in it should have small angles of contact.

    (e) A drop of liquid under no external forces is always spherical in shape.

    Medium
    4 marks
    Solve with AI
    Written solution

    (a) Consider a drop of liquid resting on a solid in air. Three interfaces meet along the line of contact: liquid–air, solid–air and solid–liquid, with surface tensions SlaS_{la}, SsaS_{sa} and SslS_{sl}. At the line of contact, SlaS_{la} acts along the tangent to the liquid surface, SsaS_{sa} pulls along the solid away from the liquid, and SslS_{sl} pulls along the solid towards the liquid. For the contact line to be in equilibrium along the solid surface,

    Slacos⁡θ+Ssl=SsaS_{la} \cos\theta + S_{sl} = S_{sa} cos⁡θ=Ssa−SslSla\cos\theta = \frac{S_{sa} - S_{sl}}{S_{la}}

    Class 11 Physics Mechanical Properties Of Fluids

    For mercury on glass, Ssl>SsaS_{sl} > S_{sa}, so cos⁡θ\cos\theta is negative and the angle of contact θ\theta is obtuse. For water on glass, Ssl<SsaS_{sl} < S_{sa}, so cos⁡θ\cos\theta is positive and θ\theta is acute.

    (b) Water molecules are attracted to glass more strongly than to one another: the adhesive force between water and glass is greater than the cohesive force within water. Replacing glass–air surface by glass–water surface therefore lowers the energy, so water spreads out over the glass (small, acute angle of contact): water wets glass.

    Mercury atoms attract one another much more strongly than they are attracted to glass: the cohesive force in mercury is much greater than the adhesive force between mercury and glass. Creating a mercury–glass surface costs a lot of energy, so mercury pulls itself together into drops that touch the glass over as small an area as possible (obtuse angle of contact): mercury does not wet glass.

    (c) Surface tension SS is the force per unit length acting along any line in the surface, or equivalently the surface energy per unit area. When the surface area is increased, more molecules come up from the interior to form the new surface; the surface is not stretched like a rubber sheet, so the spacing of molecules in the surface stays the same. The energy needed is the same for every unit of new area, so the total surface energy increases in proportion to the area while the energy per unit area, SS, stays the same. For example, the force F=2SlF = 2Sl needed to hold a slider on a soap film does not change as the slider is pulled out and the film grows. SS depends only on the nature of the liquid (and the medium it is in contact with) and the temperature, not on the area.

    (d) Detergent lowers the surface tension SlaS_{la} of water and also SslS_{sl} between water and the fabric (or grease). From

    cos⁡θ=Ssa−SslSla\cos\theta = \frac{S_{sa} - S_{sl}}{S_{la}}

    decreasing SlaS_{la} and SslS_{sl} makes cos⁡θ\cos\theta larger, so the angle of contact θ\theta becomes small. With a small angle of contact the water wets the cloth well and spreads into the narrow spaces between the fibres, which act like fine capillaries (the rise in a capillary, h=2Scos⁡θρgah = \dfrac{2S\cos\theta}{\rho g a}, is larger when cos⁡θ\cos\theta is larger). The detergent solution therefore soaks right into the fabric and reaches the dirt. That is why water used for washing should have a small angle of contact.

    (e) A liquid surface has surface energy, SS per unit area, and like any system the drop settles into the shape of least energy. With no external force (such as gravity) acting, the only energy that depends on the shape is the surface energy, so the drop takes the shape with the least surface area for its fixed volume. Of all shapes with a given volume, the sphere has the least surface area. Hence a free drop is spherical.

  3. 3

    Question 3

    Fill in the blanks using the word(s) from the list appended with each statement:

    (a) Surface tension of liquids generally ______ with temperatures (increases / decreases)

    (b) Viscosity of gases ______ with temperature, whereas viscosity of liquids ______ with temperature (increases / decreases)

    (c) For solids with elastic modulus of rigidity, the shearing force is proportional to ______, while for fluids it is proportional to ______ (shear strain / rate of shear strain)

    (d) For a fluid in a steady flow, the increase in flow speed at a constriction follows ______ (conservation of mass / Bernoulli's principle)

    (e) For the model of a plane in a wind tunnel, turbulence occurs at a ______ speed [than the critical speed] for turbulence for an actual plane (greater / smaller)

    Medium
    3 marks
    Solve with AI
    Written solution

    (a) decreases. As the temperature rises, the molecules move more vigorously and the attraction that holds the surface together becomes less effective, so the surface tension of a liquid usually falls with temperature.

    (b) increases; decreases. In a gas, a rise in temperature increases the random motion of the molecules, which carries more momentum between layers, so the viscosity of a gas increases. In a liquid, a rise in temperature makes the molecules more mobile and the viscosity decreases.

    (c) shear strain; rate of shear strain. A solid resists a change of shape: the shearing force is proportional to the shear strain (modulus of rigidity). A fluid keeps flowing under a shear force: the force is proportional to the rate at which the shear strain changes (coefficient of viscosity).

    (d) conservation of mass. For an incompressible fluid in steady flow, the mass (volume) passing every cross-section per second is the same, Av=constantA v = \text{constant} (the equation of continuity). Where the area AA is smaller, the speed vv must be larger. Bernoulli's principle then tells us what happens to the pressure, but the increase in speed itself follows from conservation of mass.

    (e) greater. The speed at which streamline flow breaks into turbulence depends on the size of the body: for a small model, the flow stays streamline up to a higher speed than for the full-size plane. So turbulence around the model sets in at a greater speed than the critical speed for the actual plane.

  4. 4

    Question 4

    Explain why

    (a) To keep a piece of paper horizontal, you should blow over, not under, it.

    (b) When we try to close a water tap with our fingers, fast jets of water gush through the openings between our fingers.

    (c) The size of the needle of a syringe controls flow rate better than the thumb pressure exerted by a doctor while administering an injection.

    (d) A fluid flowing out of a small hole in a vessel results in a backward thrust on the vessel.

    (e) A spinning cricket ball in air does not follow a parabolic trajectory.

    Medium
    4 marks
    Solve with AI
    Written solution

    (a) A piece of paper held at one edge droops because of its weight. When we blow over it, the air above the paper moves fast while the air below is nearly still. By Bernoulli's principle, for flow at (nearly) the same height,

    P+12ρv2=constantP + \frac{1}{2}\rho v^2 = \text{constant}

    so the pressure above the paper falls below the atmospheric pressure acting underneath. The net upward force from this pressure difference lifts the paper and keeps it horizontal. Blowing under the paper would lower the pressure below it and push it further down.

    (b) By the equation of continuity, the volume of water flowing out per second is Av=constantA v = \text{constant}. When we cover the tap with our fingers, the water has to pass through the small openings between them, so the area AA becomes much smaller and the speed vv becomes much larger. The water therefore comes out as fast jets.

    (c) The volume of liquid injected per second is Q=avQ = a v, where aa is the cross-sectional area of the needle's bore and vv is the speed in it. The barrel is wide, so the liquid in it moves very slowly. Applying Bernoulli's principle between the barrel (pressure PP due to the thumb) and the needle (pressure about PaP_a):

    P−Pa≈12ρv2P - P_a \approx \frac{1}{2}\rho v^2 Q=a2(P−Pa)ρQ = a\sqrt{\frac{2(P - P_a)}{\rho}}

    The flow rate is proportional to the area of the bore, that is to the square of its diameter, but only to the square root of the extra pressure. Doubling the thumb pressure raises the flow rate only by a factor of about 1.4, while doubling the needle diameter raises it four times. Moreover, the needle size is fixed and exact, whereas the thumb pressure varies. So the choice of needle controls the flow rate much better than the thumb pressure.

    (d) In a closed vessel at rest, the pressure on each part of the wall is balanced by the pressure on the opposite wall, and there is no net horizontal force. At a hole there is no wall, so the pressure on the wall opposite the hole is unbalanced and pushes the vessel away from the hole. Equivalently, the fluid leaves the hole with momentum in one direction every second; by Newton's third law (conservation of momentum) the vessel receives an equal and opposite momentum. This is the backward thrust on the vessel.

    (e) A spinning ball drags the air around it. On one side the air carried round by the spin moves in the same direction as the air flowing past the ball, so the speed of air relative to the ball is larger; on the other side the two oppose and the speed is smaller. By Bernoulli's principle, the pressure is lower on the faster side and higher on the slower side. This pressure difference gives a sideways force on the ball (the Magnus effect). With this extra force acting, in addition to gravity, the ball does not follow the parabolic path of a projectile; it swerves.

  5. 5

    Question 5

    A 50 kg girl wearing high heel shoes balances on a single heel. The heel is circular with a diameter 1.0 cm. What is the pressure exerted by the heel on the horizontal floor?

    Medium
    3 marks
    Solve with AI
    Written solution

    The whole weight of the girl acts on the floor through the heel.

    Force:

    F=mg=50×9.8=490 NF = mg = 50 \times 9.8 = 490\ \text{N}

    Area of the heel: radius r=0.50 cm=5.0×10−3 mr = 0.50\ \text{cm} = 5.0 \times 10^{-3}\ \text{m}

    A=πr2=π×(5.0×10−3)2=7.85×10−5 m2A = \pi r^2 = \pi \times (5.0 \times 10^{-3})^2 = 7.85 \times 10^{-5}\ \text{m}^2

    Pressure:

    P=FA=4907.85×10−5P = \frac{F}{A} = \frac{490}{7.85 \times 10^{-5}} P=6.24×106 PaP = 6.24 \times 10^{6}\ \text{Pa}

    The heel exerts a pressure of about 6.24×106 Pa6.24 \times 10^{6}\ \text{Pa} on the floor, about 60 times atmospheric pressure, which is why such heels can dent soft floors.

  6. 6

    Question 6

    Toricelli's barometer used mercury. Pascal duplicated it using French wine of density 984 kg m−3984\ \text{kg m}^{-3}. Determine the height of the wine column for normal atmospheric pressure.

    Medium
    3 marks
    Solve with AI
    Written solution

    In a barometer, the column of liquid is held up by the atmospheric pressure, with (nearly) vacuum above it. So the pressure of the column equals the atmospheric pressure:

    Pa=ρghP_a = \rho g h h=Paρg=1.013×105984×9.8h = \frac{P_a}{\rho g} = \frac{1.013 \times 10^{5}}{984 \times 9.8} h=10.5 mh = 10.5\ \text{m}

    The wine column is about 10.5 m high. This is about 14 times the 76 cm of a mercury barometer, because wine is about 14 times less dense than mercury.

  7. 7

    Question 7

    A vertical off-shore structure is built to withstand a maximum stress of 109 Pa10^{9}\ \text{Pa}. Is the structure suitable for putting up on top of an oil well in the ocean? Take the depth of the ocean to be roughly 3 km, and ignore ocean currents.

    Medium
    4 marks
    Solve with AI
    Written solution

    The greatest stress on the structure comes from the water pressure at the bottom of the ocean. With h=3 km=3×103 mh = 3\ \text{km} = 3 \times 10^{3}\ \text{m} and ρ=103 kg m−3\rho = 10^{3}\ \text{kg m}^{-3}:

    P=ρgh=103×9.8×3×103P = \rho g h = 10^{3} \times 9.8 \times 3 \times 10^{3} P=2.94×107 Pa≈3×107 PaP = 2.94 \times 10^{7}\ \text{Pa} \approx 3 \times 10^{7}\ \text{Pa}

    Compare with the maximum stress the structure can withstand:

    109 Pa3×107 Pa≈33\frac{10^{9}\ \text{Pa}}{3 \times 10^{7}\ \text{Pa}} \approx 33

    (Using the density of sea water, 1.03×103 kg m−31.03 \times 10^{3}\ \text{kg m}^{-3}, gives 3.03×107 Pa3.03 \times 10^{7}\ \text{Pa}; adding atmospheric pressure, ≈105 Pa\approx 10^{5}\ \text{Pa}, changes it even less. Neither affects the conclusion.)

    The water pressure, about 3×107 Pa3 \times 10^{7}\ \text{Pa}, is far below the 109 Pa10^{9}\ \text{Pa} the structure can withstand, so the structure is suitable.

  8. 8

    Question 8

    A hydraulic automobile lift is designed to lift cars with a maximum mass of 3000 kg. The area of cross-section of the piston carrying the load is 425 cm2425\ \text{cm}^2. What maximum pressure would the smaller piston have to bear?

    Medium
    4 marks
    Solve with AI
    Written solution

    The largest load on the big piston is the weight of a 3000 kg car:

    F=Mg=3000×9.8=2.94×104 NF = Mg = 3000 \times 9.8 = 2.94 \times 10^{4}\ \text{N}

    The area of the big piston is A=425 cm2=425×10−4 m2A = 425\ \text{cm}^2 = 425 \times 10^{-4}\ \text{m}^2, so the pressure in the liquid under it is

    P=FA=2.94×104425×10−4P = \frac{F}{A} = \frac{2.94 \times 10^{4}}{425 \times 10^{-4}} P=6.92×105 PaP = 6.92 \times 10^{5}\ \text{Pa}

    By Pascal's law, a pressure applied to an enclosed liquid is transmitted undiminished to every part of it. The pressure under the smaller piston is therefore the same.

    The smaller piston has to bear a maximum pressure of about 6.92×105 Pa6.92 \times 10^{5}\ \text{Pa} (about 7 atm). The force on it is smaller only because its area is smaller.

  9. 9

    Question 9

    A U-tube contains water and methylated spirit separated by mercury. The mercury columns in the two arms are in level with 10.0 cm of water in one arm and 12.5 cm of spirit in the other. What is the specific gravity of spirit?

    Medium
    4 marks
    Solve with AI
    Written solution

    Take the points A and B on the mercury surfaces in the two arms. They are at the same level in the same continuous liquid (mercury) at rest, so the pressures there are equal. Both arms are open to the atmosphere.

    Class 11 Physics Mechanical Properties Of Fluids

    Pa+hwρwg=Pa+hsρsgP_a + h_w \rho_w g = P_a + h_s \rho_s g ρsρw=hwhs=10.0 cm12.5 cm\frac{\rho_s}{\rho_w} = \frac{h_w}{h_s} = \frac{10.0\ \text{cm}}{12.5\ \text{cm}} ρsρw=0.80\frac{\rho_s}{\rho_w} = 0.80

    The specific gravity (relative density) of the spirit is 0.80.

  10. 10

    Question 10

    In the previous problem, if 15.0 cm of water and spirit each are further poured into the respective arms of the tube, what is the difference in the levels of mercury in the two arms? (Specific gravity of mercury = 13.6)

    Medium
    3 marks
    Solve with AI
    Written solution

    After pouring, the columns above the mercury are:

    water: hw=10.0+15.0=25.0 cmh_w = 10.0 + 15.0 = 25.0\ \text{cm}; spirit: hs=12.5+15.0=27.5 cmh_s = 12.5 + 15.0 = 27.5\ \text{cm} (specific gravity of spirit =0.80= 0.80 from the previous problem).

    Compare the pressures these columns exert, in terms of a water column: water gives 25.0 cm25.0\ \text{cm}; spirit gives 27.5×0.80=22.0 cm27.5 \times 0.80 = 22.0\ \text{cm} of water. The water arm presses harder, so the mercury is pushed down in the water arm and up in the spirit arm. Let hh be the difference between the mercury levels.

    Class 11 Physics Mechanical Properties Of Fluids

    Take A on the mercury surface in the water arm and B at the same level in the spirit arm (inside the mercury). A and B are at the same level in mercury at rest, so PA=PBP_A = P_B:

    Pa+hwρwg=Pa+hsρsg+hρHggP_a + h_w \rho_w g = P_a + h_s \rho_s g + h \rho_{Hg} g

    Dividing by ρwg\rho_w g and using specific gravities:

    25.0=27.5×0.80+13.6 h25.0 = 27.5 \times 0.80 + 13.6\, h 13.6 h=25.0−22.0=3.0 cm13.6\, h = 25.0 - 22.0 = 3.0\ \text{cm} h=3.013.6=0.221 cmh = \frac{3.0}{13.6} = 0.221\ \text{cm}

    The mercury levels differ by about 0.221 cm, with the mercury higher in the spirit arm.

  11. 11

    Question 11

    Can Bernoulli's equation be used to describe the flow of water through a rapid in a river? Explain.

    Medium
    2 marks
    Solve with AI
    Written solution

    No. Bernoulli's equation,

    P+12ρv2+ρgh=constantP + \frac{1}{2}\rho v^2 + \rho g h = \text{constant}

    applies along a streamline in a steady, streamline flow of an incompressible, non-viscous fluid. It is a statement of conservation of energy for such a flow.

    A rapid is a stretch of a river where water rushes over rocks and steps ("white water"). The flow there is turbulent: the velocity at any point changes irregularly with time, eddies form and streamlines cannot be defined. Much of the energy is also lost to the swirling motion and to friction. Since the conditions for Bernoulli's equation (steady streamline flow, no energy loss) are not met, it cannot be used to describe the flow through a rapid.

  12. 12

    Question 12

    Does it matter if one uses gauge instead of absolute pressures in applying Bernoulli's equation? Explain.

    Medium
    2 marks
    Solve with AI
    Written solution

    No, provided the atmospheric pressure is the same at the two points where the equation is applied.

    Bernoulli's equation between two points 1 and 2 on a streamline is

    P1+12ρv12+ρgh1=P2+12ρv22+ρgh2P_1 + \frac{1}{2}\rho v_1^2 + \rho g h_1 = P_2 + \frac{1}{2}\rho v_2^2 + \rho g h_2

    The gauge pressure is Pg=P−PaP_g = P - P_a. If PaP_a is the same at both points, subtracting PaP_a from both sides gives

    Pg1+12ρv12+ρgh1=Pg2+12ρv22+ρgh2P_{g1} + \frac{1}{2}\rho v_1^2 + \rho g h_1 = P_{g2} + \frac{1}{2}\rho v_2^2 + \rho g h_2

    which is the same equation with gauge pressures. Only pressure differences enter the result, and they are the same whether measured as gauge or absolute pressures.

    If the two points are so far apart in height that the atmospheric pressure is noticeably different at them, PaP_a no longer cancels, and absolute pressures must be used.

  13. 13

    Question 13

    Glycerine flows steadily through a horizontal tube of length 1.5 m and radius 1.0 cm. If the amount of glycerine collected per second at one end is 4.0×10−3 kg s−14.0 \times 10^{-3}\ \text{kg s}^{-1}, what is the pressure difference between the two ends of the tube? (Density of glycerine =1.3×103 kg m−3= 1.3 \times 10^{3}\ \text{kg m}^{-3} and viscosity of glycerine =0.83 Pa s= 0.83\ \text{Pa s}). [You may also like to check if the assumption of laminar flow in the tube is correct].

    Medium
    4 marks
    Solve with AI
    Written solution

    Volume flowing per second:

    Q=mass per secondρ=4.0×10−31.3×103=3.08×10−6 m3 s−1Q = \frac{\text{mass per second}}{\rho} = \frac{4.0 \times 10^{-3}}{1.3 \times 10^{3}} = 3.08 \times 10^{-6}\ \text{m}^3\ \text{s}^{-1}

    Pressure difference. For steady laminar flow of a viscous liquid through a horizontal tube of radius rr and length ll, the volume flow rate is given by Poiseuille's equation (quoted here as a known result; it is not derived in the textbook):

    Q=πpr48ηlQ = \frac{\pi p r^4}{8 \eta l}

    where pp is the pressure difference between the ends. So

    p=8Qηlπr4=8×3.08×10−6×0.83×1.5π×(1.0×10−2)4p = \frac{8 Q \eta l}{\pi r^4} = \frac{8 \times 3.08 \times 10^{-6} \times 0.83 \times 1.5}{\pi \times (1.0 \times 10^{-2})^4} p=975 Pa≈9.8×102 Pap = 975\ \text{Pa} \approx 9.8 \times 10^{2}\ \text{Pa}

    The pressure difference between the ends of the tube is about 9.8×102 Pa9.8 \times 10^{2}\ \text{Pa}.

    Check of laminar flow. The mean speed of the glycerine in the tube is

    v=Qπr2=3.08×10−6π×(1.0×10−2)2=9.79×10−3 m s−1v = \frac{Q}{\pi r^2} = \frac{3.08 \times 10^{-6}}{\pi \times (1.0 \times 10^{-2})^2} = 9.79 \times 10^{-3}\ \text{m s}^{-1}

    This is a very slow flow of a very viscous liquid, the situation in which flow stays streamline. A quantitative test (again quoted, not in the textbook) is the Reynolds number for flow in a tube of diameter D=2rD = 2r; flow in a tube is laminar when it is below about 2000:

    ρvDη=1.3×103×9.79×10−3×2.0×10−20.83=0.31\frac{\rho v D}{\eta} = \frac{1.3 \times 10^{3} \times 9.79 \times 10^{-3} \times 2.0 \times 10^{-2}}{0.83} = 0.31

    Since 0.310.31 is far below 2000, the assumption of laminar flow is correct.

  14. 14

    Question 14

    In a test experiment on a model aeroplane in a wind tunnel, the flow speeds on the upper and lower surfaces of the wing are 70 m s−170\ \text{m s}^{-1} and 63 m s−163\ \text{m s}^{-1} respectively. What is the lift on the wing if its area is 2.5 m22.5\ \text{m}^2? Take the density of air to be 1.3 kg m−31.3\ \text{kg m}^{-3}.

    Medium
    2 marks
    Solve with AI
    Written solution

    Let PuP_u, vu=70 m s−1v_u = 70\ \text{m s}^{-1} be the pressure and speed just above the wing, and PlP_l, vl=63 m s−1v_l = 63\ \text{m s}^{-1} those just below it. The wing is thin, so the two surfaces are at practically the same height and Bernoulli's principle gives

    Pu+12ρvu2=Pl+12ρvl2P_u + \frac{1}{2}\rho v_u^2 = P_l + \frac{1}{2}\rho v_l^2 Pl−Pu=12ρ(vu2−vl2)=12×1.3×(702−632)P_l - P_u = \frac{1}{2}\rho \left(v_u^2 - v_l^2\right) = \frac{1}{2} \times 1.3 \times \left(70^2 - 63^2\right) Pl−Pu=0.65×(4900−3969)=0.65×931=605 PaP_l - P_u = 0.65 \times (4900 - 3969) = 0.65 \times 931 = 605\ \text{Pa}

    The pressure below the wing is greater, because the air there moves more slowly. This pressure difference acting over the wing area gives the upward lift:

    F=(Pl−Pu)A=605×2.5=1.51×103 NF = (P_l - P_u) A = 605 \times 2.5 = 1.51 \times 10^{3}\ \text{N}

    The lift on the wing is about 1.51×103 N1.51 \times 10^{3}\ \text{N}.

  15. 15

    Question 15

    Figures (a) and (b) refer to the steady flow of a (non-viscous) liquid. Which of the two figures is incorrect? Why?

    Class 11 Physics Mechanical Properties Of Fluids

    Medium
    2 marks
    Solve with AI
    Written solution

    Figure (a) is incorrect.

    The height of liquid in each vertical tube measures the pressure in the pipe below it: the higher the pressure, the higher the column.

    By the equation of continuity, Av=constantA v = \text{constant}, so the liquid moves faster at the constriction, where the area is smaller, than in the wide part of the pipe. The pipe is horizontal, so Bernoulli's principle gives

    P+12ρv2=constantP + \frac{1}{2}\rho v^2 = \text{constant}

    Where the speed is greater, the pressure is smaller. So the pressure at the constriction is lower than in the wide part, and the liquid in the tube above the constriction must stand lower.

    Figure (a) shows the column above the constriction standing higher than the other, which is impossible. Figure (b), with the lower column at the constriction, is correct.

  16. 16

    Question 16

    The cylindrical tube of a spray pump has a cross-section of 8.0 cm28.0\ \text{cm}^2 one end of which has 40 fine holes each of diameter 1.0 mm. If the liquid flow inside the tube is 1.5 m min−11.5\ \text{m min}^{-1}, what is the speed of ejection of the liquid through the holes?

    Medium
    3 marks
    Solve with AI
    Written solution

    Inside the tube:

    A1=8.0 cm2=8.0×10−4 m2A_1 = 8.0\ \text{cm}^2 = 8.0 \times 10^{-4}\ \text{m}^2 v1=1.5 m min−1=1.560=2.5×10−2 m s−1v_1 = 1.5\ \text{m min}^{-1} = \frac{1.5}{60} = 2.5 \times 10^{-2}\ \text{m s}^{-1}

    Total area of the 40 holes (radius of each =0.50 mm=5.0×10−4 m= 0.50\ \text{mm} = 5.0 \times 10^{-4}\ \text{m}):

    A2=40×π×(5.0×10−4)2=3.14×10−5 m2A_2 = 40 \times \pi \times (5.0 \times 10^{-4})^2 = 3.14 \times 10^{-5}\ \text{m}^2

    All the liquid that flows along the tube leaves through the holes, so by the equation of continuity A1v1=A2v2A_1 v_1 = A_2 v_2:

    v2=A1v1A2=8.0×10−4×2.5×10−23.14×10−5v_2 = \frac{A_1 v_1}{A_2} = \frac{8.0 \times 10^{-4} \times 2.5 \times 10^{-2}}{3.14 \times 10^{-5}} v2=0.64 m s−1v_2 = 0.64\ \text{m s}^{-1}

    The liquid is ejected through the holes at about 0.64 m s−10.64\ \text{m s}^{-1}.

  17. 17

    Question 17

    A U-shaped wire is dipped in a soap solution, and removed. The thin soap film formed between the wire and the light slider supports a weight of 1.5×10−2 N1.5 \times 10^{-2}\ \text{N} (which includes the small weight of the slider). The length of the slider is 30 cm. What is the surface tension of the film?

    Medium
    3 marks
    Solve with AI
    Written solution

    The soap film has two surfaces (front and back), and each pulls on the slider with a force SS per unit length along the slider. With slider length ll, the total upward pull of the film is 2Sl2Sl. In equilibrium this balances the weight WW:

    2Sl=W2 S l = W S=W2l=1.5×10−22×0.30S = \frac{W}{2l} = \frac{1.5 \times 10^{-2}}{2 \times 0.30} S=2.5×10−2 N m−1S = 2.5 \times 10^{-2}\ \text{N m}^{-1}

    The surface tension of the soap film is 2.5×10−2 N m−12.5 \times 10^{-2}\ \text{N m}^{-1}.

  18. 18

    Question 18

    Figure (a) shows a thin liquid film supporting a small weight =4.5×10−2 N= 4.5 \times 10^{-2}\ \text{N}. What is the weight supported by a film of the same liquid at the same temperature in Fig. (b) and (c)? Explain your answer physically.

    Class 11 Physics Mechanical Properties Of Fluids

    Medium
    3 marks
    Solve with AI
    Written solution

    The film supports the same weight, 4.5×10−2 N4.5 \times 10^{-2}\ \text{N}, in both (b) and (c).

    The weight hangs from the slider, and the only upward force on the slider is the pull of the film along the slider's length. The film has two surfaces, each pulling with SS per unit length, so the upward force is 2Sl2Sl, where l=40 cml = 40\ \text{cm} is the length of the slider. In (a):

    S=W2l=4.5×10−22×0.40=5.625×10−2 N m−1S = \frac{W}{2l} = \frac{4.5 \times 10^{-2}}{2 \times 0.40} = 5.625 \times 10^{-2}\ \text{N m}^{-1}

    In (b) and (c) the liquid and the temperature are the same, so SS is the same, and the slider has the same length, 40 cm. Hence

    W=2Sl=2×5.625×10−2×0.40=4.5×10−2 NW = 2 S l = 2 \times 5.625 \times 10^{-2} \times 0.40 = 4.5 \times 10^{-2}\ \text{N}

    Physically, surface tension is a force per unit length acting along the boundary of the film. The film pulls on the slider only along the line where it meets the slider, so the force depends only on SS and on the length of that line. The height, area or shape of the rest of the film (a taller rectangle in (b), a pointed top in (c)) only changes the total surface energy stored in the film, not the force per unit length at the slider.

  19. 19

    Question 19

    What is the pressure inside the drop of mercury of radius 3.00 mm at room temperature? Surface tension of mercury at that temperature (20 °C) is 4.65×10−1 N m−14.65 \times 10^{-1}\ \text{N m}^{-1}. The atmospheric pressure is 1.01×105 Pa1.01 \times 10^{5}\ \text{Pa}. Also give the excess pressure inside the drop.

    Medium
    3 marks
    Solve with AI
    Written solution

    A drop of liquid has one surface (liquid–air), so the pressure inside exceeds the pressure outside by

    Pi−Po=2SrP_i - P_o = \frac{2S}{r}

    With S=4.65×10−1 N m−1S = 4.65 \times 10^{-1}\ \text{N m}^{-1} (the value given) and r=3.00×10−3 mr = 3.00 \times 10^{-3}\ \text{m}:

    Pi−Po=2×4.65×10−13.00×10−3=310 PaP_i - P_o = \frac{2 \times 4.65 \times 10^{-1}}{3.00 \times 10^{-3}} = 310\ \text{Pa}

    Excess pressure inside the drop =310 Pa= 310\ \text{Pa}.

    The pressure outside the drop is the atmospheric pressure, so

    Pi=1.01×105+310=1.0131×105 PaP_i = 1.01 \times 10^{5} + 310 = 1.0131 \times 10^{5}\ \text{Pa}

    Pressure inside the drop ≈1.01×105 Pa\approx 1.01 \times 10^{5}\ \text{Pa} (to the three significant figures of the data; the excess pressure is too small to change the third figure).

  20. 20

    Question 20

    What is the excess pressure inside a bubble of soap solution of radius 5.00 mm, given that the surface tension of soap solution at the temperature (20 °C) is 2.50×10−2 N m−12.50 \times 10^{-2}\ \text{N m}^{-1}? If an air bubble of the same dimension were formed at depth of 40.0 cm inside a container containing the soap solution (of relative density 1.20), what would be the pressure inside the bubble? (1 atmospheric pressure is 1.01×105 Pa1.01 \times 10^{5}\ \text{Pa}).

    Medium
    4 marks
    Solve with AI
    Written solution

    Given S=2.50×10−2 N m−1S = 2.50 \times 10^{-2}\ \text{N m}^{-1} and r=5.00 mm=5.00×10−3 mr = 5.00\ \text{mm} = 5.00 \times 10^{-3}\ \text{m}.

    Soap bubble in air. A soap bubble is a thin film with two surfaces (inside and outside), so the excess pressure is

    Pi−Po=4Sr=4×2.50×10−25.00×10−3=20.0 PaP_i - P_o = \frac{4S}{r} = \frac{4 \times 2.50 \times 10^{-2}}{5.00 \times 10^{-3}} = 20.0\ \text{Pa}

    Excess pressure inside the soap bubble =20.0 Pa= 20.0\ \text{Pa}.

    Air bubble inside the solution. An air bubble in a liquid has only one surface (liquid–air), so its excess pressure is

    2Sr=2×2.50×10−25.00×10−3=10.0 Pa\frac{2S}{r} = \frac{2 \times 2.50 \times 10^{-2}}{5.00 \times 10^{-3}} = 10.0\ \text{Pa}

    The pressure in the liquid just outside the bubble, at depth h=0.400 mh = 0.400\ \text{m} in a solution of density ρ=1.20×103 kg m−3\rho = 1.20 \times 10^{3}\ \text{kg m}^{-3}, is

    Po=Pa+ρgh=1.01×105+1.20×103×9.8×0.400=1.01×105+4704 PaP_o = P_a + \rho g h = 1.01 \times 10^{5} + 1.20 \times 10^{3} \times 9.8 \times 0.400 = 1.01 \times 10^{5} + 4704\ \text{Pa}

    So the pressure inside the air bubble is

    Pi=Pa+ρgh+2Sr=1.01×105+4704+10.0=1.057×105 PaP_i = P_a + \rho g h + \frac{2S}{r} = 1.01 \times 10^{5} + 4704 + 10.0 = 1.057 \times 10^{5}\ \text{Pa}

    Pressure inside the air bubble ≈1.06×105 Pa\approx 1.06 \times 10^{5}\ \text{Pa}.

Inside Ch 9

What Class 11 Physics Ch 9 covers

The sections of the chapter, in the order the book takes them. Every question above comes from one of these.

  1. 01Pressure
  2. 02Atmospheric Pressure And Gauge Pressure
  3. 03Streamline Flow
  4. 04Bernoullis Principle
  5. 05Torricellis Law
  6. 06Dynamic Lift
  7. 07Viscosity
Common questions

Class 11 Physics Ch 9 questions students ask

How many questions are there in Class 11 Physics Ch 9?

20 questions. Every one is solved step by step on this page.

Are these Class 11 Physics solutions free?

Yes. Every question and its full working is free to read, with no account needed.

Can I download the Class 11 Physics Ch 9 solutions as a PDF?

There is no PDF to download. Every solution is on this page instead, which means it is searchable, always the current syllabus, and readable on a phone. Use your browser's print option if you want it on paper.