Confirming your payment

Skip to content

Opening your dashboard

Class 11 Physics Chapter 5: Work Energy Power Solutions

23 textbook questions with step-by-step answers, free to read, for CBSE 2026-27.

AI Tutor

Get talked through Ch 5, not just shown the answer

Reading a finished solution is not the same as being able to do it. The AI tutor takes one question at a time and works it with you, in your own words, until you can.

  • Ask it out loud, in your own words
  • It gives you the next step, not the answer
  • Stuck on part (ii)? Start there
Ch 5 solutions

23 questions with solutions

2–5 marks · Mixed difficulty

  1. 1

    Question 1

    The sign of work done by a force on a body is important to understand. State carefully if the following quantities are positive or negative:

    (a) work done by a man in lifting a bucket out of a well by means of a rope tied to the bucket.

    (b) work done by gravitational force in the above case,

    (c) work done by friction on a body sliding down an inclined plane,

    (d) work done by an applied force on a body moving on a rough horizontal plane with uniform velocity,

    (e) work done by the resistive force of air on a vibrating pendulum in bringing it to rest.

    Medium
    5 marks
    Solve with AI
    Written solution

    The work done by a constant force F⃗\vec{F} during a displacement d⃗\vec{d} is

    W=F⃗⋅d⃗=Fdcos⁡θW = \vec{F}\cdot\vec{d} = Fd\cos\theta

    where θ\theta is the angle between the force and the displacement. The work is positive when 0∘≤θ<90∘0^\circ \le \theta < 90^\circ and negative when 90∘<θ≤180∘90^\circ < \theta \le 180^\circ.

    (a) Positive. The man pulls the rope upward and the bucket moves upward, so θ=0∘\theta = 0^\circ and W=Fd>0W = Fd > 0.

    (b) Negative. Gravity (mgmg) acts downward while the bucket moves upward, so θ=180∘\theta = 180^\circ and W=−mgd<0W = -mgd < 0.

    (c) Negative. Kinetic friction on the body acts up the incline, opposite to its displacement down the incline, so θ=180∘\theta = 180^\circ.

    (d) Positive. The applied force acts along the direction of motion, so θ=0∘\theta = 0^\circ. (Because the velocity is uniform, the applied force just balances friction; friction does an equal amount of negative work, so the net work on the body is zero and its kinetic energy does not change.)

    (e) Negative. The air resistance always acts opposite to the velocity of the bob, on the forward swing as well as on the backward swing, so it does negative work throughout. This steadily removes mechanical energy from the pendulum, which is why it finally comes to rest.

  2. 2

    Question 2

    A body of mass 2 kg initially at rest moves under the action of an applied horizontal force of 7 N on a table with coefficient of kinetic friction = 0.1. Compute the

    (a) work done by the applied force in 10 s,

    (b) work done by friction in 10 s,

    (c) work done by the net force on the body in 10 s,

    (d) change in kinetic energy of the body in 10 s,

    and interpret your results.

    Medium
    4 marks
    Solve with AI
    Written solution

    Taking g=9.8 m s−2g = 9.8\ \text{m s}^{-2}. The forces on the body are shown below (the weight and the normal force are vertical and balance each other).

    Class 11 Physics Work Energy Power

    Friction: the normal force is N=mg=2×9.8=19.6 NN = mg = 2 \times 9.8 = 19.6\ \text{N}, so

    f=μkN=0.1×19.6=1.96 Nf = \mu_k N = 0.1 \times 19.6 = 1.96\ \text{N}

    Net force and acceleration:

    Fnet=7−1.96=5.04 N,a=Fnetm=5.042=2.52 m s−2F_{\text{net}} = 7 - 1.96 = 5.04\ \text{N}, \qquad a = \frac{F_{\text{net}}}{m} = \frac{5.04}{2} = 2.52\ \text{m s}^{-2}

    Distance moved in 10 s (starting from rest):

    s=12at2=12×2.52×(10)2=126 ms = \frac{1}{2}at^2 = \frac{1}{2} \times 2.52 \times (10)^2 = 126\ \text{m}

    (a) The applied force acts along the displacement:

    WF=Fs=7×126=882 JW_F = Fs = 7 \times 126 = 882\ \text{J}

    Work done by the applied force == 882 J.

    (b) Friction acts opposite to the displacement (θ=180∘\theta = 180^\circ):

    Wf=−fs=−1.96×126=−246.96 JW_f = -fs = -1.96 \times 126 = -246.96\ \text{J}

    Work done by friction ≈\approx −247 J.

    (c) The net force acts along the displacement:

    Wnet=Fnet s=5.04×126=635.04 JW_{\text{net}} = F_{\text{net}}\, s = 5.04 \times 126 = 635.04\ \text{J}

    Work done by the net force ≈\approx 635 J. (Check: 882+(−247)=635882 + (-247) = 635 J; the weight and normal force do no work because they are perpendicular to the displacement.)

    (d) Speed after 10 s: v=at=2.52×10=25.2 m s−1v = at = 2.52 \times 10 = 25.2\ \text{m s}^{-1}. The body started from rest, so

    ΔK=12mv2−0=12×2×(25.2)2=635.04 J\Delta K = \frac{1}{2}mv^2 - 0 = \frac{1}{2} \times 2 \times (25.2)^2 = 635.04\ \text{J}

    Change in kinetic energy ≈\approx 635 J.

    Interpretation: the change in kinetic energy of the body is exactly equal to the work done by the net force on it. This is the work–energy theorem. Of the 882 J supplied by the applied force, about 247 J is used up against friction (it appears as heat) and the remaining 635 J becomes kinetic energy of the body.

  3. 3

    Question 3

    Given in the figure below are examples of some potential energy functions in one dimension. The total energy of the particle is indicated by a cross on the ordinate axis. In each case, specify the regions, if any, in which the particle cannot be found for the given energy. Also, indicate the minimum total energy the particle must have in each case. Think of simple physical contexts for which these potential energy shapes are relevant.

    Class 11 Physics Work Energy Power

    Hard
    5 marks
    Solve with AI
    Written solution

    Key idea. The total mechanical energy is E=K+V(x)E = K + V(x), so the kinetic energy at any point is

    K=E−V(x)K = E - V(x)

    Kinetic energy can never be negative. Hence the particle can be found only where V(x)≤EV(x) \le E; any region where V(x)>EV(x) > E is forbidden. Also, since K≥0K \ge 0, the total energy can never be less than the lowest value of V(x)V(x); this lowest value is the minimum total energy the particle must have (it is then at rest at the bottom of the curve).

    In the answer figure below, the forbidden regions are shaded and the energy EE is shown as a dashed line.

    Class 11 Physics Work Energy Power

    (a) V=0V = 0 for x<ax < a and V=V0V = V_0 for x>ax > a, with 0<E<V00 < E < V_0.

    • For x>ax > a, V0>EV_0 > E, so KK would be negative. The particle cannot be found in the region x>ax > a. It moves freely for x<ax < a.
    • The lowest value of VV is 0, so the minimum total energy is zero.
    • Physical context: a ball rolling on a level floor towards a high step (or a wall). If its kinetic energy is less than the potential energy it would have on top of the step, it cannot climb up and simply comes back.

    (b) Here EE lies below the potential energy curve at every xx. Even the lowest part of the curve (the level for x<0x < 0) is above EE.

    • The particle cannot be found anywhere, since KK would be negative at every point.
    • To exist at all, the particle needs a total energy at least equal to the lowest value of VV, i.e. the height of the step for x<0x < 0 (which lies below V0V_0). This is the minimum total energy for this case.
    • Physical context: a ball on a set of terraces or a staircase of different heights, where V=mghV = mgh on each level. A ball whose total energy is less than mghmgh of even the lowest terrace cannot be on any of them.

    (c) V=V0V = V_0 for x<ax < a and for x>bx > b; V=−V1V = -V_1 for a<x<ba < x < b; and −V1<E<V0-V_1 < E < V_0.

    • For x<ax < a and x>bx > b, V0>EV_0 > E. The particle cannot be found in the regions x<ax < a and x>bx > b. It is trapped between x=ax = a and x=bx = b, moving to and fro.
    • The lowest value of VV is −V1-V_1, so the minimum total energy is −V1-V_1.
    • Physical context: a potential well, e.g. a ball in a ditch (or valley) between two high banks: it rolls back and forth and cannot get out unless it gains enough energy. An electron bound in an atom is another example.

    (d) V=−V1V = -V_1 for −a2<x<a2-\dfrac{a}{2} < x < \dfrac{a}{2}; just outside this, VV jumps up (to about V0V_0) and then falls off gradually to zero far away. The level EE meets the falling parts of the curve at x=±b2x = \pm\dfrac{b}{2}.

    • For −b2<x<−a2-\dfrac{b}{2} < x < -\dfrac{a}{2} and a2<x<b2\dfrac{a}{2} < x < \dfrac{b}{2}, the curve is above EE. The particle cannot be found in these two regions.
    • It can be found inside the well (∣x∣<a2|x| < \dfrac{a}{2}) or outside the barriers (∣x∣>b2|x| > \dfrac{b}{2}). A particle inside cannot get out, and a particle outside cannot get in, because the barriers separate these regions.
    • The lowest value of VV is −V1-V_1, so the minimum total energy is −V1-V_1.
    • Physical context: a ball in the crater at the top of a volcano-shaped hill. A ball inside the crater cannot climb over the rim, and a ball rolling towards the hill from outside cannot get over the rim into the crater unless it has enough energy. (A particle bound inside an atomic nucleus behaves in a similar way.)
  4. 4

    Question 4

    The potential energy function for a particle executing linear simple harmonic motion is given by V(x)=kx22V(x) = \dfrac{kx^2}{2}, where kk is the force constant of the oscillator. For k=0.5 N m−1k = 0.5\ \text{N m}^{-1}, the graph of V(x)V(x) versus xx is shown in the figure. Show that a particle of total energy 1 J moving under this potential must 'turn back' when it reaches x=±2x = \pm 2 m.

    Class 11 Physics Work Energy Power

    Medium
    3 marks
    Solve with AI
    Written solution

    The total energy of the particle is E=K+V(x)E = K + V(x), so its kinetic energy at position xx is

    K=E−V(x)=E−12kx2K = E - V(x) = E - \frac{1}{2}kx^2

    Since KK cannot be negative, the particle can only be where 12kx2≤E\dfrac{1}{2}kx^2 \le E.

    Turning points. The particle stops momentarily (K=0K = 0) where all its energy is potential energy:

    12kxm2=E⇒xm2=2Ek=2×10.5=4 m2\frac{1}{2}kx_m^2 = E \quad\Rightarrow\quad x_m^2 = \frac{2E}{k} = \frac{2 \times 1}{0.5} = 4\ \text{m}^2 xm=±2 mx_m = \pm 2\ \text{m}

    Why it turns back. For ∣x∣>2|x| > 2 m, V(x)>1V(x) > 1 J =E= E, which would make KK negative, so the particle can never go beyond x=±2x = \pm 2 m. At x=±2x = \pm 2 m its speed is zero, and the force on it,

    F=−dVdx=−kxF = -\frac{dV}{dx} = -kx

    (magnitude 0.5×2=10.5 \times 2 = 1 N), points back towards x=0x = 0. So the particle is pulled back and returns.

    Class 11 Physics Work Energy Power

    Hence a particle of total energy 1 J must turn back at x=±2x = \pm 2 m; it oscillates between these two points.

  5. 5

    Question 5

    Answer the following :

    (a) The casing of a rocket in flight burns up due to friction. At whose expense is the heat energy required for burning obtained? The rocket or the atmosphere?

    (b) Comets move around the sun in highly elliptical orbits. The gravitational force on the comet due to the sun is not normal to the comet's velocity in general. Yet the work done by the gravitational force over every complete orbit of the comet is zero. Why?

    (c) An artificial satellite orbiting the earth in very thin atmosphere loses its energy gradually due to dissipation against atmospheric resistance, however small. Why then does its speed increase progressively as it comes closer and closer to the earth?

    (d) In figure (i) the man walks 2 m carrying a mass of 15 kg on his hands. In figure (ii), he walks the same distance pulling the rope behind him. The rope goes over a pulley, and a mass of 15 kg hangs at its other end. In which case is the work done greater?

    Class 11 Physics Work Energy Power

    Medium
    4 marks
    Solve with AI
    Written solution

    (a) The rocket. Friction from the air acts opposite to the rocket's motion and does negative work on it. This reduces the rocket's mechanical energy (kinetic + potential), and the energy removed appears as the heat that burns the casing. So the heat is obtained at the expense of the rocket's own energy, not the atmosphere's.

    (b) The gravitational force is a conservative force. The work done by a conservative force depends only on the initial and final positions, not on the path followed: W=−(Vf−Vi)W = -(V_f - V_i). After one complete orbit the comet is back at its starting point, so Vf=ViV_f = V_i and the work done over a complete orbit is zero.

    (In detail: while the comet approaches the sun, gravity has a component along its velocity and does positive work, speeding it up; while it moves away, the component is opposite to its velocity and the work is negative, slowing it down. The two cancel exactly over a complete orbit.)

    (c) Air resistance does negative work, so the total energy E=K+VE = K + V of the satellite decreases slowly. As a result the satellite drops into a lower orbit, closer to the earth. As it comes closer, its gravitational potential energy decreases, and this decrease is larger than the energy lost to air resistance. The difference appears as an increase in kinetic energy:

    ΔK=ΔE−ΔV>0(ΔE small and negative, ΔV larger and negative)\Delta K = \Delta E - \Delta V > 0 \qquad (\Delta E \text{ small and negative},\ \Delta V \text{ larger and negative})

    So its speed increases progressively even though its total energy falls.

    (d) Taking g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    Case (i): the man holds the 15 kg mass with an upward (vertical) force equal to its weight, while the displacement is 2 m horizontal. The angle between force and displacement is 90∘90^\circ:

    W1=Fdcos⁡90∘=0W_1 = Fd\cos 90^\circ = 0

    Case (ii): to raise the hanging mass steadily, the man pulls the rope with a force equal to the weight of the mass,

    F=mg=15×9.8=147 NF = mg = 15 \times 9.8 = 147\ \text{N}

    and this force acts along the direction in which he walks (θ=0∘\theta = 0^\circ):

    W2=Fd=147×2=294 JW_2 = Fd = 147 \times 2 = 294\ \text{J}

    (This equals the potential energy gained by the 15 kg mass, which rises by 2 m.)

    So the work done is greater in case (ii): 294 J, compared with zero in case (i).

  6. 6

    Question 6

    Underline the correct alternative :

    (a) When a conservative force does positive work on a body, the potential energy of the body increases/decreases/remains unaltered.

    (b) Work done by a body against friction always results in a loss of its kinetic/potential energy.

    (c) The rate of change of total momentum of a many-particle system is proportional to the external force/sum of the internal forces on the system.

    (d) In an inelastic collision of two bodies, the quantities which do not change after the collision are the total kinetic energy/total linear momentum/total energy of the system of two bodies.

    Medium
    4 marks
    Solve with AI
    Written solution

    (a) decreases. For a conservative force, the work done equals the decrease in potential energy:

    Wc=−ΔVW_c = -\Delta V

    If WcW_c is positive, ΔV\Delta V is negative, so the potential energy decreases. Example: when a body falls, gravity does positive work and the body's gravitational potential energy decreases.

    (b) kinetic. A body doing work against friction uses up its kinetic energy (which appears as heat). For example, a block sliding on a rough floor slows down and stops.

    (c) external force. Internal forces occur in equal and opposite pairs (Newton's third law), so their sum is zero and they cannot change the total momentum. Hence

    dP⃗dt=F⃗ext\frac{d\vec{P}}{dt} = \vec{F}_{\text{ext}}

    (d) total linear momentum and total energy. Total linear momentum is conserved in every collision, since only internal forces act during the impact. Total energy is also conserved. The total kinetic energy, however, changes in an inelastic collision, because part of it is converted into heat, sound and energy of deformation.

  7. 7

    Question 7

    State if each of the following statements is true or false. Give reasons for your answer.

    (a) In an elastic collision of two bodies, the momentum and energy of each body is conserved.

    (b) Total energy of a system is always conserved, no matter what internal and external forces on the body are present.

    (c) Work done in the motion of a body over a closed loop is zero for every force in nature.

    (d) In an inelastic collision, the final kinetic energy is always less than the initial kinetic energy of the system.

    Medium
    4 marks
    Solve with AI
    Written solution

    (a) False. In an elastic collision, the total momentum and the total kinetic energy of the two-body system are conserved, not those of each body separately. Each body exerts a force on the other, so the momentum and energy of each body change. For example, when two equal masses collide elastically head-on with one at rest, they exchange velocities: the moving body stops and the other one moves off.

    (b) False. The total energy of an isolated system (no external forces doing work) is conserved. External forces can do work on the system and change its total energy; for example, a person pushing a trolley increases its energy. So the statement "no matter what external forces are present" is wrong.

    (c) False. The work done over a closed loop is zero only for conservative forces such as gravity or the spring force. For non-conservative forces like friction it is not zero: a block pushed around a closed path on a rough floor has negative work done on it by friction on every part of the path.

    (d) Not always true (usually true). Usually some kinetic energy is converted into heat, sound and deformation, so the final kinetic energy is less than the initial kinetic energy. However, if stored energy is released during the collision (for example, the colliding bodies set off an explosive, or a compressed spring between them is released), the final kinetic energy can be greater than the initial kinetic energy.

  8. 8

    Question 8

    Answer carefully, with reasons :

    (a) In an elastic collision of two billiard balls, is the total kinetic energy conserved during the short time of collision of the balls (i.e. when they are in contact)?

    (b) Is the total linear momentum conserved during the short time of an elastic collision of two balls?

    (c) What are the answers to (a) and (b) for an inelastic collision?

    (d) If the potential energy of two billiard balls depends only on the separation distance between their centres, is the collision elastic or inelastic? (Note, we are talking here of potential energy corresponding to the force during collision, not gravitational potential energy).

    Medium
    4 marks
    Solve with AI
    Written solution

    (a) No. While the balls are in contact they are compressed (deformed). Part of their kinetic energy is stored temporarily as elastic potential energy, so the total kinetic energy during contact is less than before. In an elastic collision this energy is fully returned as kinetic energy when the balls separate, so the total kinetic energy after the collision equals that before, but it is not conserved at every instant during contact.

    (b) Yes. During contact the only forces are the equal and opposite forces the balls exert on each other; these are internal forces of the two-ball system. There is no net external force, so the total linear momentum is conserved at every instant, during the collision as well.

    (c) For an inelastic collision:

    • Total kinetic energy is not conserved during the contact, and it is not restored afterwards either: part of it is permanently converted into heat, sound and deformation.
    • Total linear momentum is conserved, during and after the collision, for the same reason as in (b).

    (d) Elastic. A force whose potential energy depends only on the separation between the centres is a conservative force. When the balls move apart again to their original (large) separation, the potential energy returns to its original value, so all the kinetic energy that was stored is given back. The total kinetic energy after the collision equals that before, so the collision is elastic.

  9. 9

    Question 9

    A body is initially at rest. It undergoes one-dimensional motion with constant acceleration. The power delivered to it at time tt is proportional to

    (i) t1/2t^{1/2}

    (ii) tt

    (iii) t3/2t^{3/2}

    (iv) t2t^2

    Medium
    2 marks
    Solve with AI
    Written solution

    The correct option is (ii): P∝tP \propto t.

    Since the acceleration aa is constant, the force F=maF = ma is also constant. The body starts from rest (u=0u = 0), so its velocity at time tt is

    v=u+at=atv = u + at = at

    The power delivered is

    P=Fv=(ma)(at)=ma2 tP = Fv = (ma)(at) = ma^2\,t

    Here mm and aa are constants, so

    P∝tP \propto t
  10. 10

    Question 10

    A body is moving unidirectionally under the influence of a source of constant power. Its displacement in time tt is proportional to

    (i) t1/2t^{1/2}

    (ii) tt

    (iii) t3/2t^{3/2}

    (iv) t2t^2

    Medium
    2 marks
    Solve with AI
    Written solution

    The correct option is (iii): x∝t3/2x \propto t^{3/2}.

    Let the body of mass mm start from rest at t=0t = 0, and let the constant power be PP. For motion in a straight line,

    P=Fv=(mdvdt)vP = Fv = \left(m\frac{dv}{dt}\right)v

    Step 1: velocity. Separating the variables,

    v dv=Pm dtv\,dv = \frac{P}{m}\,dt

    Integrating from v=0v = 0 at t=0t = 0 to vv at time tt (PP and mm are constants):

    v22=Pm t⇒v=2Pm  t1/2\frac{v^2}{2} = \frac{P}{m}\,t \quad\Rightarrow\quad v = \sqrt{\frac{2P}{m}}\;t^{1/2}

    So v∝t1/2v \propto t^{1/2}.

    Step 2: displacement. Since v=dxdtv = \dfrac{dx}{dt},

    dx=2Pm  t1/2 dtdx = \sqrt{\frac{2P}{m}}\;t^{1/2}\,dt

    Integrating from x=0x = 0 at t=0t = 0:

    x=2Pm×23 t3/2x = \sqrt{\frac{2P}{m}} \times \frac{2}{3}\,t^{3/2}

    The factor in front is a constant, so

    x∝t3/2x \propto t^{3/2}

    (Check with dimensions: Pm\dfrac{P}{m} has dimensions [L2T−3][\text{L}^2\text{T}^{-3}], and Pm t3/2\sqrt{\dfrac{P}{m}}\,t^{3/2} has dimensions [LT−3/2][T3/2]=[L][\text{L}\text{T}^{-3/2}][\text{T}^{3/2}] = [\text{L}], a length, as it should be.)

  11. 11

    Question 11

    A body constrained to move along the z-axis of a coordinate system is subject to a constant force F\mathbf{F} given by

    F=−i^+2j^+3k^ N\mathbf{F} = -\hat{\mathbf{i}} + 2\hat{\mathbf{j}} + 3\hat{\mathbf{k}}\ \text{N}

    where i^,j^,k^\hat{\mathbf{i}}, \hat{\mathbf{j}}, \hat{\mathbf{k}} are unit vectors along the x-, y- and z-axis of the system respectively. What is the work done by this force in moving the body a distance of 4 m along the z-axis?

    Medium
    3 marks
    Solve with AI
    Written solution

    The body moves 4 m along the z-axis, so its displacement is

    d⃗=0 i^+0 j^+4 k^ m\vec{d} = 0\,\hat{i} + 0\,\hat{j} + 4\,\hat{k}\ \text{m}

    The work done by a constant force is the scalar product W=F⃗⋅d⃗=Fxdx+Fydy+FzdzW = \vec{F}\cdot\vec{d} = F_x d_x + F_y d_y + F_z d_z:

    W=(−1)(0)+(2)(0)+(3)(4)=12 JW = (-1)(0) + (2)(0) + (3)(4) = 12\ \text{J}

    The work done by the force is 12 J.

    Only the z-component of the force (3 N) does work. The x- and y-components are perpendicular to the displacement, so they do no work (they are balanced by the constraint that keeps the body on the z-axis).

  12. 12

    Question 12

    An electron and a proton are detected in a cosmic ray experiment, the first with kinetic energy 10 keV, and the second with 100 keV. Which is faster, the electron or the proton? Obtain the ratio of their speeds. (electron mass =9.11×10−31= 9.11 \times 10^{-31} kg, proton mass =1.67×10−27= 1.67 \times 10^{-27} kg, 1 eV =1.60×10−19= 1.60 \times 10^{-19} J).

    Medium
    4 marks
    Solve with AI
    Written solution

    From K=12mv2K = \dfrac{1}{2}mv^2, the speed of a particle is

    v=2Kmv = \sqrt{\frac{2K}{m}}

    Kinetic energies in joules:

    Ke=10×103×1.60×10−19=1.60×10−15 JK_e = 10 \times 10^3 \times 1.60 \times 10^{-19} = 1.60 \times 10^{-15}\ \text{J} Kp=100×103×1.60×10−19=1.60×10−14 JK_p = 100 \times 10^3 \times 1.60 \times 10^{-19} = 1.60 \times 10^{-14}\ \text{J}

    Speeds:

    ve=2×1.60×10−159.11×10−31=5.93×107 m s−1v_e = \sqrt{\frac{2 \times 1.60 \times 10^{-15}}{9.11 \times 10^{-31}}} = 5.93 \times 10^{7}\ \text{m s}^{-1} vp=2×1.60×10−141.67×10−27=4.38×106 m s−1v_p = \sqrt{\frac{2 \times 1.60 \times 10^{-14}}{1.67 \times 10^{-27}}} = 4.38 \times 10^{6}\ \text{m s}^{-1}

    Ratio of speeds (directly from the formula):

    vevp=KeKp×mpme=10100×1.67×10−279.11×10−31=183.3=13.5\frac{v_e}{v_p} = \sqrt{\frac{K_e}{K_p} \times \frac{m_p}{m_e}} = \sqrt{\frac{10}{100} \times \frac{1.67 \times 10^{-27}}{9.11 \times 10^{-31}}} = \sqrt{183.3} = 13.5

    The electron is faster, and ve:vp≈v_e : v_p \approx 13.5 : 1. Although the proton has ten times the kinetic energy, its mass is about 1833 times larger, so its speed is much smaller.

  13. 13

    Question 13

    A rain drop of radius 2 mm falls from a height of 500 m above the ground. It falls with decreasing acceleration (due to viscous resistance of the air) until at half its original height, it attains its maximum (terminal) speed, and moves with uniform speed thereafter. What is the work done by the gravitational force on the drop in the first and second half of its journey? What is the work done by the resistive force in the entire journey if its speed on reaching the ground is 10 m s−1^{-1}?

    Medium
    5 marks
    Solve with AI
    Written solution

    Taking g=9.8 m s−2g = 9.8\ \text{m s}^{-2} and the density of water ρ=103 kg m−3\rho = 10^3\ \text{kg m}^{-3}.

    Mass of the drop (r=2 mm=2×10−3r = 2\ \text{mm} = 2 \times 10^{-3} m):

    m=43πr3ρ=43×3.14×(2×10−3)3×103≈3.35×10−5 kgm = \frac{4}{3}\pi r^3 \rho = \frac{4}{3} \times 3.14 \times (2 \times 10^{-3})^3 \times 10^3 \approx 3.35 \times 10^{-5}\ \text{kg}

    Work done by gravity in each half. Each half of the journey is h=250h = 250 m. Gravity is a constant force acting along the (downward) displacement, so

    Wg=mgh=3.35×10−5×9.8×250=0.082 JW_g = mgh = 3.35 \times 10^{-5} \times 9.8 \times 250 = 0.082\ \text{J}

    The work done by gravity is 0.082 J in the first half and 0.082 J in the second half. It is the same in both halves because it depends only on the force and the displacement, not on whether the drop is accelerating or moving uniformly.

    Work done by the resistive force. Apply the work–energy theorem to the whole journey (the drop starts from rest):

    Wg+Wr=ΔK=12mv2−0W_g + W_r = \Delta K = \frac{1}{2}mv^2 - 0

    Total work by gravity over 500 m:

    Wg=mg(500)=3.35×10−5×9.8×500=0.16415 JW_g = mg(500) = 3.35 \times 10^{-5} \times 9.8 \times 500 = 0.16415\ \text{J}

    Kinetic energy on reaching the ground:

    12mv2=12×3.35×10−5×(10)2=1.675×10−3 J\frac{1}{2}mv^2 = \frac{1}{2} \times 3.35 \times 10^{-5} \times (10)^2 = 1.675 \times 10^{-3}\ \text{J}

    Therefore

    Wr=12mv2−Wg=0.001675−0.16415=−0.16248 J≈−0.162 JW_r = \frac{1}{2}mv^2 - W_g = 0.001675 - 0.16415 = -0.16248\ \text{J} \approx -0.162\ \text{J}

    The work done by the resistive force over the entire journey is −0.162 J. It is negative because the resistance acts opposite to the motion; almost all the energy supplied by gravity is used up against air resistance.

  14. 14

    Question 14

    A molecule in a gas container hits a horizontal wall with speed 200 m s−1^{-1} and angle 30° with the normal, and rebounds with the same speed. Is momentum conserved in the collision? Is the collision elastic or inelastic?

    Class 11 Physics Work Energy Power

    Medium
    5 marks
    Solve with AI
    Written solution

    Let the mass of the molecule be mm (in kg) and u=v=200 m s−1u = v = 200\ \text{m s}^{-1}. The wall exerts a force on the molecule only along the normal, so the component of velocity along the wall is unchanged. Since the speed is also unchanged, the normal component keeps its size and only reverses: the molecule rebounds at 30∘30^\circ to the normal.

    Class 11 Physics Work Energy Power

    Components of the molecule's velocity:

    along the wall: usin⁡30∘=200×0.5=100 m s−1 (before and after)\text{along the wall: } u\sin 30^\circ = 200 \times 0.5 = 100\ \text{m s}^{-1} \ \text{(before and after)} along the normal: ucos⁡30∘=200×0.866=173.2 m s−1 (towards the wall before, away from it after)\text{along the normal: } u\cos 30^\circ = 200 \times 0.866 = 173.2\ \text{m s}^{-1} \ \text{(towards the wall before, away from it after)}

    Is momentum conserved?

    The molecule's momentum along the wall is unchanged, but along the normal it changes from 173.2 m173.2\,m towards the wall to 173.2 m173.2\,m away from the wall. (Here and below, momenta are in kg m s−1\text{kg m s}^{-1} with mm in kg.) The change in the molecule's momentum is

    Δp=2mucos⁡30∘=2×200×0.866×m=346.4 m\Delta p = 2mu\cos 30^\circ = 2 \times 200 \times 0.866 \times m = 346.4\,m

    directed away from the wall. So the momentum of the molecule alone is not conserved.

    However, by Newton's third law the molecule pushes the wall with an equal and opposite force during the impact, so the wall (with the container attached to it) receives an equal momentum 346.4 m346.4\,m towards the outside. The forces are internal to the molecule + wall system, so the total momentum of the molecule + wall system is conserved. Because the wall is enormously heavier than the molecule, its resulting velocity is negligibly small.

    Elastic or inelastic?

    The molecule's speed is the same before and after (200 m s−1^{-1}), so its kinetic energy 12m(200)2\frac{1}{2}m(200)^2 is unchanged. The kinetic energy given to the massive wall is negligible. The total kinetic energy is therefore conserved, so the collision is elastic.

  15. 15

    Question 15

    A pump on the ground floor of a building can pump up water to fill a tank of volume 30 m3^3 in 15 min. If the tank is 40 m above the ground, and the efficiency of the pump is 30%, how much electric power is consumed by the pump?

    Medium
    3 marks
    Solve with AI
    Written solution

    Taking g=9.8 m s−2g = 9.8\ \text{m s}^{-2} and the density of water ρ=103 kg m−3\rho = 10^3\ \text{kg m}^{-3}.

    Mass of water lifted:

    m=ρV=103×30=3.0×104 kgm = \rho V = 10^3 \times 30 = 3.0 \times 10^4\ \text{kg}

    Work done in lifting it through 40 m (gain in potential energy):

    W=mgh=3.0×104×9.8×40=1.176×107 JW = mgh = 3.0 \times 10^4 \times 9.8 \times 40 = 1.176 \times 10^7\ \text{J}

    Useful (output) power, with t=15 min=900t = 15\ \text{min} = 900 s:

    Pout=Wt=1.176×107900=1.307×104 WP_{\text{out}} = \frac{W}{t} = \frac{1.176 \times 10^7}{900} = 1.307 \times 10^4\ \text{W}

    Electric (input) power. Efficiency η=PoutPin=0.30\eta = \dfrac{P_{\text{out}}}{P_{\text{in}}} = 0.30, so

    Pin=Poutη=1.307×1040.30=4.36×104 WP_{\text{in}} = \frac{P_{\text{out}}}{\eta} = \frac{1.307 \times 10^4}{0.30} = 4.36 \times 10^4\ \text{W}

    The pump consumes about 43.6 kW of electric power.

  16. 16

    Question 16

    Two identical ball bearings in contact with each other and resting on a frictionless table are hit head-on by another ball bearing of the same mass moving initially with a speed VV. If the collision is elastic, which of the following (figure) is a possible result after collision?

    Class 11 Physics Work Energy Power

    Medium
    4 marks
    Solve with AI
    Written solution

    Let each ball bearing have mass mm. Before the collision:

    pinitial=mV,Kinitial=12mV2p_{\text{initial}} = mV, \qquad K_{\text{initial}} = \frac{1}{2}mV^2

    In an elastic collision both the total momentum and the total kinetic energy must be the same after the collision.

    CaseTotal momentum afterTotal kinetic energy afterBoth conserved?
    (i)2m×V2=mV2m \times \frac{V}{2} = mV12(2m)(V2)2=14mV2\frac{1}{2}(2m)\left(\frac{V}{2}\right)^2 = \frac{1}{4}mV^2No
    (ii)m×V=mVm \times V = mV12mV2\frac{1}{2}mV^2Yes
    (iii)3m×V3=mV3m \times \frac{V}{3} = mV12(3m)(V3)2=16mV2\frac{1}{2}(3m)\left(\frac{V}{3}\right)^2 = \frac{1}{6}mV^2No

    Momentum is conserved in all three cases, but kinetic energy is conserved only in case (ii). Hence case (ii) is the only possible result: balls 1 and 2 are at rest and ball 3 moves off with speed VV.

    Physical picture: in a head-on elastic collision between equal masses with one at rest, the two balls exchange velocities. Ball 1 hits ball 2, stops, and ball 2 moves with VV; ball 2 then hits ball 3, stops, and ball 3 moves off with VV.

  17. 17

    Question 17

    The bob A of a pendulum released from 30° to the vertical hits another bob B of the same mass at rest on a table as shown in the figure. How high does the bob A rise after the collision? Neglect the size of the bobs and assume the collision to be elastic.

    Class 11 Physics Work Energy Power

    Medium
    2 marks
    Solve with AI
    Written solution

    Bob A swings down and, at the lowest point of its path, hits bob B head-on while moving horizontally with some speed vv.

    For a head-on elastic collision in which the target is at rest, the velocities after the collision are

    vA′=mA−mBmA+mB v,vB′=2mAmA+mB vv_A' = \frac{m_A - m_B}{m_A + m_B}\,v, \qquad v_B' = \frac{2m_A}{m_A + m_B}\,v

    Here mA=mB=mm_A = m_B = m, so

    vA′=0,vB′=vv_A' = 0, \qquad v_B' = v

    The two bobs simply exchange velocities: bob A comes to rest at the lowest point and bob B moves off along the table with A's speed. Since A has no kinetic energy left after the collision, it cannot rise at all.

    Bob A does not rise after the collision (height = 0).

  18. 18

    Question 18

    The bob of a pendulum is released from a horizontal position. If the length of the pendulum is 1.5 m, what is the speed with which the bob arrives at the lowermost point, given that it dissipated 5% of its initial energy against air resistance?

    Medium
    3 marks
    Solve with AI
    Written solution

    Taking g=9.8 m s−2g = 9.8\ \text{m s}^{-2} and the lowest point as the zero of potential energy.

    When the bob is released from the horizontal position it is at rest, at a height equal to the length of the pendulum, h=l=1.5h = l = 1.5 m, above the lowest point. Its initial energy is therefore all potential energy:

    Ei=mglE_i = mgl

    5% of this is dissipated against air resistance, so 95% becomes kinetic energy at the lowest point:

    12mv2=0.95 mgl\frac{1}{2}mv^2 = 0.95\,mgl

    The mass cancels:

    v=2×0.95×gl=2×0.95×9.8×1.5=27.93=5.28 m s−1v = \sqrt{2 \times 0.95 \times g l} = \sqrt{2 \times 0.95 \times 9.8 \times 1.5} = \sqrt{27.93} = 5.28\ \text{m s}^{-1}

    The bob arrives at the lowest point with a speed of about 5.3 m s−1^{-1}.

  19. 19

    Question 19

    A trolley of mass 300 kg carrying a sandbag of 25 kg is moving uniformly with a speed of 27 km/h on a frictionless track. After a while, sand starts leaking out of a hole on the floor of the trolley at the rate of 0.05 kg s−1^{-1}. What is the speed of the trolley after the entire sand bag is empty?

    Medium
    2 marks
    Solve with AI
    Written solution

    The speed remains 27 km/h.

    Reason:

    • The track is frictionless, and the only other forces on the trolley + sand system (gravity and the normal reaction) are vertical. So there is no external horizontal force, and the horizontal momentum of the system is conserved.
    • The sand simply falls out through the floor. At the instant it leaves, each grain has the same horizontal velocity as the trolley, so it carries away exactly its own share of momentum. It does not push the trolley forward or backward, i.e. it exerts no horizontal force on the trolley.
    • Hence nothing changes the trolley's horizontal velocity, and it continues to move at 27 km/h after all the sand has leaked out.

    The rate of leaking (0.05 kg s−1^{-1}) only tells us how long the sandbag takes to empty (25/0.05=50025 / 0.05 = 500 s); it does not affect the speed. (The speed would change only if the sand were thrown out with a velocity relative to the trolley, for example backwards.)

  20. 20

    Question 20

    A body of mass 0.5 kg travels in a straight line with velocity v=a x3/2v = a\,x^{3/2} where a=5 m−1/2 s−1a = 5\ \text{m}^{-1/2}\ \text{s}^{-1}. What is the work done by the net force during its displacement from x=0x = 0 to x=2x = 2 m?

    Medium
    3 marks
    Solve with AI
    Written solution

    By the work–energy theorem, the work done by the net force equals the change in kinetic energy:

    Wnet=12mvf2−12mvi2W_{\text{net}} = \frac{1}{2}m v_f^2 - \frac{1}{2}m v_i^2

    Velocity at x=0x = 0:

    vi=5×03/2=0v_i = 5 \times 0^{3/2} = 0

    Velocity at x=2x = 2 m:

    vf=5×23/2=5×22=102=14.1 m s−1,vf2=200 m2s−2v_f = 5 \times 2^{3/2} = 5 \times 2\sqrt{2} = 10\sqrt{2} = 14.1\ \text{m s}^{-1}, \qquad v_f^2 = 200\ \text{m}^2\text{s}^{-2}

    Work done by the net force:

    Wnet=12×0.5×200−0=50 JW_{\text{net}} = \frac{1}{2} \times 0.5 \times 200 - 0 = 50\ \text{J}

    The work done by the net force is 50 J.

  21. 21

    Question 21

    The blades of a windmill sweep out a circle of area AA.

    (a) If the wind flows at a velocity vv perpendicular to the circle, what is the mass of the air passing through it in time tt?

    (b) What is the kinetic energy of the air?

    (c) Assume that the windmill converts 25% of the wind's energy into electrical energy, and that A=30A = 30 m2^2, v=36v = 36 km/h and the density of air is 1.2 kg m−3^{-3}. What is the electrical power produced?

    Medium
    4 marks
    Solve with AI
    Written solution

    (a) In time tt the air moves a distance vtvt. So the air that passes through the circle in this time fills a cylinder of cross-section AA and length vtvt:

    volume=Avt,m=ρAvt\text{volume} = Avt, \qquad m = \rho A v t

    where ρ\rho is the density of air. Mass of air =ρAvt= \rho A v t.

    (b) Kinetic energy of this air:

    K=12mv2=12(ρAvt)v2=12ρAv3tK = \frac{1}{2}mv^2 = \frac{1}{2}(\rho A v t)v^2 = \frac{1}{2}\rho A v^3 t

    Kinetic energy of the air =12ρAv3t= \frac{1}{2}\rho A v^3 t.

    (c) v=36 km/h=36×10003600=10 m s−1v = 36\ \text{km/h} = 36 \times \dfrac{1000}{3600} = 10\ \text{m s}^{-1}.

    Power carried by the wind (kinetic energy per unit time):

    Pwind=Kt=12ρAv3=12×1.2×30×(10)3=1.8×104 WP_{\text{wind}} = \frac{K}{t} = \frac{1}{2}\rho A v^3 = \frac{1}{2} \times 1.2 \times 30 \times (10)^3 = 1.8 \times 10^4\ \text{W}

    25% of this is converted into electrical energy:

    Pelec=0.25×1.8×104=4500 WP_{\text{elec}} = 0.25 \times 1.8 \times 10^4 = 4500\ \text{W}

    The electrical power produced is 4.5 kW.

  22. 22

    Question 22

    A person trying to lose weight (dieter) lifts a 10 kg mass, one thousand times, to a height of 0.5 m each time. Assume that the potential energy lost each time she lowers the mass is dissipated.

    (a) How much work does she do against the gravitational force?

    (b) Fat supplies 3.8×1073.8 \times 10^7 J of energy per kilogram which is converted to mechanical energy with a 20% efficiency rate. How much fat will the dieter use up?

    Medium
    3 marks
    Solve with AI
    Written solution

    Taking g=9.8 m s−2g = 9.8\ \text{m s}^{-2}.

    (a) Each time she lifts the mass through h=0.5h = 0.5 m, she does work mghmgh against gravity. (When she lowers it, the potential energy is dissipated, so she does not get it back.) For 1000 lifts:

    W=1000×mgh=1000×10×9.8×0.5=4.9×104 JW = 1000 \times mgh = 1000 \times 10 \times 9.8 \times 0.5 = 4.9 \times 10^4\ \text{J}

    Work done against gravity == 4.9×1044.9 \times 10^4 J (49 kJ).

    (b) Only 20% of the energy in fat becomes mechanical energy. Useful mechanical energy from 1 kg of fat:

    0.20×3.8×107=7.6×106 J0.20 \times 3.8 \times 10^7 = 7.6 \times 10^6\ \text{J}

    Mass of fat needed to supply 4.9×1044.9 \times 10^4 J of mechanical work:

    mfat=4.9×1047.6×106=6.45×10−3 kgm_{\text{fat}} = \frac{4.9 \times 10^4}{7.6 \times 10^6} = 6.45 \times 10^{-3}\ \text{kg}

    The dieter uses up about 6.45×10−36.45 \times 10^{-3} kg (about 6.5 g) of fat, which shows that exercise alone burns fat rather slowly.

  23. 23

    Question 23

    A family uses 8 kW of power.

    (a) Direct solar energy is incident on the horizontal surface at an average rate of 200 W per square meter. If 20% of this energy can be converted to useful electrical energy, how large an area is needed to supply 8 kW?

    (b) Compare this area to that of the roof of a typical house.

    Medium
    4 marks
    Solve with AI
    Written solution

    (a) Useful electrical power obtained from each square metre:

    0.20×200=40 W m−20.20 \times 200 = 40\ \text{W m}^{-2}

    Area needed to supply 8 kW=80008\ \text{kW} = 8000 W:

    A=800040=200 m2A = \frac{8000}{40} = 200\ \text{m}^2

    An area of 200 m2^2 is needed.

    (b) An area of 200 m2^2 is roughly a square of side 200≈14\sqrt{200} \approx 14 m, i.e. about 14 m×14 m14\ \text{m} \times 14\ \text{m}. This is comparable to the roof of a large house. The roof of a typical smaller house is less than this, so it could supply only part of the family's need.

Inside Ch 5

What Class 11 Physics Ch 5 covers

The sections of the chapter, in the order the book takes them. Every question above comes from one of these.

  1. 01Scalar Product
  2. 02Variable Force
  3. 03Kinetic Energy
  4. 04Work Energy Theorem
  5. 05Potential Energy
  6. 06Conservation of Mechanical Energy
  7. 07Potential Energy Of A Spring
Common questions

Class 11 Physics Ch 5 questions students ask

How many questions are there in Class 11 Physics Ch 5?

23 questions. Every one is solved step by step on this page.

Are these Class 11 Physics solutions free?

Yes. Every question and its full working is free to read, with no account needed.

Can I download the Class 11 Physics Ch 5 solutions as a PDF?

There is no PDF to download. Every solution is on this page instead, which means it is searchable, always the current syllabus, and readable on a phone. Use your browser's print option if you want it on paper.