Confirming your payment

Skip to content

Opening your dashboard

Class 11 Physics Chapter 1: Units And Measurments Solutions

17 textbook questions with step-by-step answers, free to read, for CBSE 2026-27.

AI Tutor

Get talked through Ch 1, not just shown the answer

Reading a finished solution is not the same as being able to do it. The AI tutor takes one question at a time and works it with you, in your own words, until you can.

  • Ask it out loud, in your own words
  • It gives you the next step, not the answer
  • Stuck on part (ii)? Start there
Ch 1 solutions

17 questions with solutions

2–5 marks · Mixed difficulty

  1. 1

    Question 1

    Fill in the blanks

    (a) The volume of a cube of side 1 cm is equal to ..... m3\text{m}^3

    (b) The surface area of a solid cylinder of radius 2.0 cm and height 10.0 cm is equal to ..... (mm)2(\text{mm})^2

    (c) A vehicle moving with a speed of 18 km h−1\text{h}^{-1} covers ..... m in 1 s

    (d) The relative density of lead is 11.3. Its density is ..... g cm−3\text{g cm}^{-3} or ..... kg m−3\text{kg m}^{-3}.

    Easy
    5 marks
    Solve with AI
    Written solution

    (a) 10−6 m310^{-6}\ \text{m}^3

    Since 1 cm=10−2 m1\ \text{cm} = 10^{-2}\ \text{m},

    V=(1 cm)3=(10−2 m)3=10−6 m3V = (1\ \text{cm})^3 = (10^{-2}\ \text{m})^3 = 10^{-6}\ \text{m}^3

    (b) 1.5×104 (mm)21.5 \times 10^{4}\ (\text{mm})^2

    A solid cylinder has a curved surface (2πrh2\pi r h) and two flat circular ends (each πr2\pi r^2).

    Class 11 Physics Units And Measurments

    Total surface area S=2πrh+2πr2=2πr(r+h)S = 2\pi r h + 2\pi r^2 = 2\pi r (r + h). In millimetres, r=2.0 cm=20 mmr = 2.0\ \text{cm} = 20\ \text{mm} and h=10.0 cm=100 mmh = 10.0\ \text{cm} = 100\ \text{mm}:

    S=2π×20×(20+100)=2π×2400=1.508×104 mm2S = 2\pi \times 20 \times (20 + 100) = 2\pi \times 2400 = 1.508 \times 10^{4}\ \text{mm}^2

    The radius is known to only 2 significant figures (2.0 cm), so the answer is rounded to 2 significant figures: S=1.5×104 (mm)2S = 1.5 \times 10^{4}\ (\text{mm})^2. (The factor 2π2\pi is exact and does not limit the significant figures.)

    (c) 5 m

    18 km h−1=18×1000 m3600 s=5 m s−118\ \text{km h}^{-1} = \frac{18 \times 1000\ \text{m}}{3600\ \text{s}} = 5\ \text{m s}^{-1}

    Distance covered in 1 s =5 m s−1×1 s=5 m= 5\ \text{m s}^{-1} \times 1\ \text{s} = 5\ \text{m}.

    (d) 11.3 g cm−311.3\ \text{g cm}^{-3} or 1.13×104 kg m−31.13 \times 10^{4}\ \text{kg m}^{-3}

    Relative density =density of leaddensity of water= \dfrac{\text{density of lead}}{\text{density of water}}, and the density of water is 1 g cm−31\ \text{g cm}^{-3}. So the density of lead is 11.3×1=11.3 g cm−311.3 \times 1 = 11.3\ \text{g cm}^{-3}.

    1 g cm−3=10−3 kg10−6 m3=103 kg m−31\ \text{g cm}^{-3} = \frac{10^{-3}\ \text{kg}}{10^{-6}\ \text{m}^3} = 10^{3}\ \text{kg m}^{-3} 11.3 g cm−3=11.3×103 kg m−3=1.13×104 kg m−311.3\ \text{g cm}^{-3} = 11.3 \times 10^{3}\ \text{kg m}^{-3} = 1.13 \times 10^{4}\ \text{kg m}^{-3}
  2. 2

    Question 2

    Fill in the blanks by suitable conversion of units

    (a) 1 kg m2 s−2=1\ \text{kg m}^2\,\text{s}^{-2} = ..... g cm2 s−2\text{g cm}^2\,\text{s}^{-2}

    (b) 1 m=1\ \text{m} = ..... ly

    (c) 3.0 m s−2=3.0\ \text{m s}^{-2} = ..... km h−2\text{km h}^{-2}

    (d) G=6.67×10−11 N m2 (kg)−2=G = 6.67 \times 10^{-11}\ \text{N m}^2\,(\text{kg})^{-2} = ..... (cm)3 s−2 g−1(\text{cm})^3\,\text{s}^{-2}\,\text{g}^{-1}.

    Medium
    4 marks
    Solve with AI
    Written solution

    Units are treated like algebraic quantities: replace each unit by its value in the new units and simplify.

    (a) 107 g cm2 s−210^{7}\ \text{g cm}^2\,\text{s}^{-2}

    1 kg m2 s−2=(103 g)(102 cm)2 s−2=103×104 g cm2 s−2=107 g cm2 s−21\ \text{kg m}^2\,\text{s}^{-2} = (10^{3}\ \text{g})(10^{2}\ \text{cm})^2\,\text{s}^{-2} = 10^{3} \times 10^{4}\ \text{g cm}^2\,\text{s}^{-2} = 10^{7}\ \text{g cm}^2\,\text{s}^{-2}

    (b) 1.06×10−16 ly1.06 \times 10^{-16}\ \text{ly} (about 10−1610^{-16} ly)

    One light year is the distance light travels in one year: 1 ly=(3.00×108 m s−1)(3.156×107 s)=9.47×1015 m1\ \text{ly} = (3.00 \times 10^{8}\ \text{m s}^{-1})(3.156 \times 10^{7}\ \text{s}) = 9.47 \times 10^{15}\ \text{m}. Hence

    1 m=19.47×1015 ly=1.06×10−16 ly1\ \text{m} = \frac{1}{9.47 \times 10^{15}}\ \text{ly} = 1.06 \times 10^{-16}\ \text{ly}

    (c) 3.9×104 km h−23.9 \times 10^{4}\ \text{km h}^{-2}

    1 m=10−3 km1\ \text{m} = 10^{-3}\ \text{km} and 1 s=13600 h1\ \text{s} = \dfrac{1}{3600}\ \text{h}, so 1 s−2=(3600)2 h−21\ \text{s}^{-2} = (3600)^2\ \text{h}^{-2}.

    3.0 m s−2=3.0×10−3×(3600)2 km h−2=3.888×104 km h−23.0\ \text{m s}^{-2} = 3.0 \times 10^{-3} \times (3600)^2\ \text{km h}^{-2} = 3.888 \times 10^{4}\ \text{km h}^{-2}

    Since 3.0 has 2 significant figures, the result is 3.9×104 km h−23.9 \times 10^{4}\ \text{km h}^{-2}.

    (d) 6.67×10−8 cm3 s−2 g−16.67 \times 10^{-8}\ \text{cm}^3\,\text{s}^{-2}\,\text{g}^{-1}

    First write the newton in base units, 1 N=1 kg m s−21\ \text{N} = 1\ \text{kg m s}^{-2}:

    G=6.67×10−11 (kg m s−2) m2 kg−2=6.67×10−11 m3 s−2 kg−1G = 6.67 \times 10^{-11}\ (\text{kg m s}^{-2})\,\text{m}^2\,\text{kg}^{-2} = 6.67 \times 10^{-11}\ \text{m}^3\,\text{s}^{-2}\,\text{kg}^{-1}

    Now 1 m3=(102 cm)3=106 cm31\ \text{m}^3 = (10^{2}\ \text{cm})^3 = 10^{6}\ \text{cm}^3 and 1 kg−1=(103 g)−1=10−3 g−11\ \text{kg}^{-1} = (10^{3}\ \text{g})^{-1} = 10^{-3}\ \text{g}^{-1}:

    G=6.67×10−11×106×10−3 cm3 s−2 g−1=6.67×10−8 cm3 s−2 g−1G = 6.67 \times 10^{-11} \times 10^{6} \times 10^{-3}\ \text{cm}^3\,\text{s}^{-2}\,\text{g}^{-1} = 6.67 \times 10^{-8}\ \text{cm}^3\,\text{s}^{-2}\,\text{g}^{-1}
  3. 3

    Question 3

    A calorie is a unit of heat (energy in transit) and it equals about 4.2 J where 1 J=1 kg m2 s−21\ \text{J} = 1\ \text{kg m}^2\,\text{s}^{-2}. Suppose we employ a system of units in which the unit of mass equals α\alpha kg, the unit of length equals β\beta m, the unit of time is γ\gamma s. Show that a calorie has a magnitude 4.2 α−1β−2γ24.2\ \alpha^{-1} \beta^{-2} \gamma^{2} in terms of the new units.

    Medium
    4 marks
    Solve with AI
    Written solution

    A physical quantity is the same whatever units are used, so its numerical value nn and its unit uu satisfy n1u1=n2u2n_1 u_1 = n_2 u_2.

    In SI, 1 cal=4.2 kg m2 s−21\ \text{cal} = 4.2\ \text{kg m}^2\,\text{s}^{-2}, so n1=4.2n_1 = 4.2. Energy has the dimensional formula [M1L2T−2][\text{M}^1\text{L}^2\text{T}^{-2}], so

    n1 [M11L12T1−2]=n2 [M21L22T2−2]n_1\,[\text{M}_1^{1}\text{L}_1^{2}\text{T}_1^{-2}] = n_2\,[\text{M}_2^{1}\text{L}_2^{2}\text{T}_2^{-2}]
    QuantitySI systemNew system
    unit of massM1=1\text{M}_1 = 1 kgM2=α\text{M}_2 = \alpha kg
    unit of lengthL1=1\text{L}_1 = 1 mL2=β\text{L}_2 = \beta m
    unit of timeT1=1\text{T}_1 = 1 sT2=γ\text{T}_2 = \gamma s
    n2=n1(M1M2)1(L1L2)2(T1T2)−2=4.2(1α)(1β)2(1γ)−2n_2 = n_1 \left(\frac{\text{M}_1}{\text{M}_2}\right)^{1} \left(\frac{\text{L}_1}{\text{L}_2}\right)^{2} \left(\frac{\text{T}_1}{\text{T}_2}\right)^{-2} = 4.2 \left(\frac{1}{\alpha}\right)\left(\frac{1}{\beta}\right)^{2}\left(\frac{1}{\gamma}\right)^{-2} n2=4.2 α−1β−2γ2n_2 = 4.2\ \alpha^{-1}\beta^{-2}\gamma^{2}

    So in the new units a calorie has the magnitude 4.2 α−1β−2γ24.2\ \alpha^{-1}\beta^{-2}\gamma^{2}.

  4. 4

    Question 4

    Explain this statement clearly :

    "To call a dimensional quantity 'large' or 'small' is meaningless without specifying a standard for comparison". In view of this, reframe the following statements wherever necessary :

    (a) atoms are very small objects

    (b) a jet plane moves with great speed

    (c) the mass of Jupiter is very large

    (d) the air inside this room contains a large number of molecules

    (e) a proton is much more massive than an electron

    (f) the speed of sound is much smaller than the speed of light.

    Medium
    4 marks
    Solve with AI
    Written solution

    A dimensional quantity is measured by comparing it with a standard (a unit). A length of 1 km is huge compared with the size of a cell but tiny compared with the distance to the Moon. So "large" or "small" has meaning only when we say compared with what. A dimensionless ratio of two like quantities, however, can be called large or small by itself.

    (a) Atoms are very small compared with the sharp tip of a pin (an atom is about 10−1010^{-10} m across; a pin tip is about 10−410^{-4} m).

    (b) A jet plane moves with great speed compared with a car or a fast train (about 250 m s−1250\ \text{m s}^{-1} against about 30 m s−130\ \text{m s}^{-1}).

    (c) The mass of Jupiter is very large compared with the mass of the Earth (about 318 times).

    (d) The air inside this room contains a large number of molecules compared with the number in one mole of air (a room of volume about 50 m350\ \text{m}^3 holds roughly 20002000 mol).

    (e) A proton is much more massive than an electron — this statement already compares two quantities (the proton is about 1836 times as massive), so it is correct as it stands.

    (f) The speed of sound is much smaller than the speed of light — this also already makes a comparison (about 340 m s−1340\ \text{m s}^{-1} against 3×108 m s−13 \times 10^{8}\ \text{m s}^{-1}), so it is correct as it stands.

  5. 5

    Question 5

    A new unit of length is chosen such that the speed of light in vacuum is unity. What is the distance between the Sun and the Earth in terms of the new unit if light takes 8 min and 20 s to cover this distance ?

    Medium
    2 marks
    Solve with AI
    Written solution

    If the speed of light is to be 1 (new unit of length) per second, the new unit of length must be the distance light travels in 1 s:

    1 new unit=3×108 m1\ \text{new unit} = 3 \times 10^{8}\ \text{m}

    Time taken by light from the Sun to the Earth =8 min 20 s=8×60+20=500 s= 8\ \text{min}\ 20\ \text{s} = 8 \times 60 + 20 = 500\ \text{s}.

    Distance == speed ×\times time =(1 new unit per s)×500 s=500= (1\ \text{new unit per s}) \times 500\ \text{s} = 500 new units.

    (Check: in metres the distance is 3×108×500=1.5×10113 \times 10^{8} \times 500 = 1.5 \times 10^{11} m, and 1.5×1011 m÷3×1081.5 \times 10^{11}\ \text{m} \div 3 \times 10^{8} m per new unit =500= 500 new units.)

    The Sun–Earth distance is 500 new units.

  6. 6

    Question 6

    Which of the following is the most precise device for measuring length :

    (a) a vernier callipers with 20 divisions on the sliding scale

    (b) a screw gauge of pitch 1 mm and 100 divisions on the circular scale

    (c) an optical instrument that can measure length to within a wavelength of light ?

    Easy
    3 marks
    Solve with AI
    Written solution

    The most precise device is the one that can measure the smallest length (the smallest least count).

    (a) Vernier callipers with 20 vernier divisions (1 main-scale division = 1 mm):

    least count=1 mm20=0.05 mm=5×10−5 m\text{least count} = \frac{1\ \text{mm}}{20} = 0.05\ \text{mm} = 5 \times 10^{-5}\ \text{m}

    (b) Screw gauge:

    least count=pitchnumber of circular divisions=1 mm100=0.01 mm=1×10−5 m\text{least count} = \frac{\text{pitch}}{\text{number of circular divisions}} = \frac{1\ \text{mm}}{100} = 0.01\ \text{mm} = 1 \times 10^{-5}\ \text{m}

    (c) Optical instrument: it measures to within one wavelength of light. Visible light has a wavelength of about 6×10−7 m6 \times 10^{-7}\ \text{m} (6000 Å), so its least count is about 6×10−7 m6 \times 10^{-7}\ \text{m}.

    Since 6×10−7 m<1×10−5 m<5×10−5 m6 \times 10^{-7}\ \text{m} < 1 \times 10^{-5}\ \text{m} < 5 \times 10^{-5}\ \text{m}, the optical instrument (c) is the most precise.

  7. 7

    Question 7

    A student measures the thickness of a human hair by looking at it through a microscope of magnification 100. He makes 20 observations and finds that the average width of the hair in the field of view of the microscope is 3.5 mm. What is the estimate on the thickness of hair ?

    Medium
    3 marks
    Solve with AI
    Written solution

    Magnification tells how many times larger the image is than the object:

    m=width of imageactual thickness of hairm = \frac{\text{width of image}}{\text{actual thickness of hair}}

    The average width of the image is 3.5 mm and m=100m = 100, so

    thickness of hair=3.5 mm100=0.035 mm=3.5×10−5 m\text{thickness of hair} = \frac{3.5\ \text{mm}}{100} = 0.035\ \text{mm} = 3.5 \times 10^{-5}\ \text{m}

    The estimate of the thickness of the hair is 0.035 mm. (Taking the average of 20 observations makes this estimate more reliable than a single reading.)

  8. 8

    Question 8

    Answer the following :

    (a) You are given a thread and a metre scale. How will you estimate the diameter of the thread ?

    (b) A screw gauge has a pitch of 1.0 mm and 200 divisions on the circular scale. Do you think it is possible to increase the accuracy of the screw gauge arbitrarily by increasing the number of divisions on the circular scale ?

    (c) The mean diameter of a thin brass rod is to be measured by vernier callipers. Why is a set of 100 measurements of the diameter expected to yield a more reliable estimate than a set of 5 measurements only ?

    Medium
    5 marks
    Solve with AI
    Written solution

    (a) The thread is far thinner than the smallest division (1 mm) of a metre scale, so it cannot be measured directly. Wind the thread closely on a uniform pencil so that the turns touch one another, and count the number of turns nn. Measure the length ll of the wound part with the metre scale.

    Class 11 Physics Units And Measurments

    Each turn occupies a length equal to the diameter of the thread, so

    diameter of thread=ln\text{diameter of thread} = \frac{l}{n}

    Winding many turns makes ll large enough to measure with the metre scale.

    (b) Least count =pitchnumber of circular divisions=1.0 mm200=0.005 mm= \dfrac{\text{pitch}}{\text{number of circular divisions}} = \dfrac{1.0\ \text{mm}}{200} = 0.005\ \text{mm}.

    In principle, more divisions give a smaller least count. In practice the accuracy cannot be increased arbitrarily: the divisions become too close for the eye to tell apart, and it is impossible to make the pitch of the screw perfectly uniform along its whole length. So increasing the divisions beyond a limit does not improve the accuracy.

    (c) Each reading contains a small random error, which is equally likely to be positive or negative. When many readings are averaged, the positive and negative errors largely cancel. With 100 readings the cancellation is much better than with 5, so the mean of 100 readings is a more reliable estimate of the true diameter.

  9. 9

    Question 9

    The photograph of a house occupies an area of 1.75 cm21.75\ \text{cm}^2 on a 35 mm slide. The slide is projected on to a screen, and the area of the house on the screen is 1.55 m21.55\ \text{m}^2. What is the linear magnification of the projector-screen arrangement.

    Medium
    3 marks
    Solve with AI
    Written solution

    Area on the slide =1.75 cm2=1.75×10−4 m2= 1.75\ \text{cm}^2 = 1.75 \times 10^{-4}\ \text{m}^2; area on the screen =1.55 m2= 1.55\ \text{m}^2.

    areal magnification=1.551.75×10−4=8.857×103\text{areal magnification} = \frac{1.55}{1.75 \times 10^{-4}} = 8.857 \times 10^{3}

    Area is length ×\times length, so when every length is magnified mm times the area is magnified m2m^2 times. Hence the linear magnification is

    m=8.857×103=94.1m = \sqrt{8.857 \times 10^{3}} = 94.1

    Both areas are given to 3 significant figures, so the linear magnification is 94.1.

  10. 10

    Question 10

    State the number of significant figures in the following :

    (a) 0.007 m20.007\ \text{m}^2

    (b) 2.64×10242.64 \times 10^{24} kg

    (c) 0.2370 g cm−30.2370\ \text{g cm}^{-3}

    (d) 6.320 J

    (e) 6.032 N m−26.032\ \text{N m}^{-2}

    (f) 0.0006032 m20.0006032\ \text{m}^2

    Medium
    3 marks
    Solve with AI
    Written solution
    QuantitySignificant figuresReason
    (a) 0.007 m20.007\ \text{m}^21zeros to the left of the first non-zero digit in a number less than 1 are not significant; only 7 counts
    (b) 2.64×10242.64 \times 10^{24} kg3in scientific notation all digits of aa (2, 6, 4) are significant; the power of 10 does not count
    (c) 0.2370 g cm−30.2370\ \text{g cm}^{-3}4the leading 0 is not significant; the trailing zero after the decimal point is (2, 3, 7, 0)
    (d) 6.320 J4the trailing zero in a number with a decimal point is significant (6, 3, 2, 0)
    (e) 6.032 N m−26.032\ \text{N m}^{-2}4a zero between two non-zero digits is significant (6, 0, 3, 2)
    (f) 0.0006032 m20.0006032\ \text{m}^24the leading zeros are not significant; the zero between 6 and 3 is (6, 0, 3, 2)
  11. 11

    Question 11

    The length, breadth and thickness of a rectangular sheet of metal are 4.234 m, 1.005 m, and 2.01 cm respectively. Give the area and volume of the sheet to correct significant figures.

    Medium
    3 marks
    Solve with AI
    Written solution

    Length =4.234= 4.234 m (4 s.f.), breadth =1.005= 1.005 m (4 s.f.), thickness =2.01 cm=2.01×10−2= 2.01\ \text{cm} = 2.01 \times 10^{-2} m (3 s.f.). In multiplication the result keeps as many significant figures as the factor with the fewest.

    Area (of one face) =4.234×1.005=4.255 17 m2= 4.234 \times 1.005 = 4.255\,17\ \text{m}^2. Both factors have 4 significant figures, so

    area=4.255 m2\text{area} = 4.255\ \text{m}^2

    Volume =4.234×1.005×2.01×10−2=0.085 529 m3= 4.234 \times 1.005 \times 2.01 \times 10^{-2} = 0.085\,529\ \text{m}^3. The thickness has only 3 significant figures, so

    volume=0.0855 m3=8.55×10−2 m3\text{volume} = 0.0855\ \text{m}^3 = 8.55 \times 10^{-2}\ \text{m}^3
  12. 12

    Question 12

    The mass of a box measured by a grocer's balance is 2.30 kg. Two gold pieces of masses 20.15 g and 20.17 g are added to the box. What is (a) the total mass of the box, (b) the difference in the masses of the pieces to correct significant figures ?

    Medium
    4 marks
    Solve with AI
    Written solution

    In addition and subtraction the result keeps as many decimal places as the quantity with the fewest decimal places.

    (a) Convert to kilograms: 20.15 g=0.0201520.15\ \text{g} = 0.02015 kg and 20.17 g=0.0201720.17\ \text{g} = 0.02017 kg.

    total mass=2.30+0.02015+0.02017=2.340 32 kg\text{total mass} = 2.30 + 0.02015 + 0.02017 = 2.340\,32\ \text{kg}

    The grocer's reading 2.30 kg has only 2 decimal places, so the total mass is 2.34 kg. (Some answer keys print 2.3 kg; applying the decimal-places rule of Section 1.3.1 to the reading 2.30 kg, which has two decimal places, gives 2.34 kg.)

    (b) Difference =20.17−20.15=0.02= 20.17 - 20.15 = 0.02 g. Both values have 2 decimal places, so the difference is 0.02 g.

  13. 13

    Question 13

    A famous relation in physics relates 'moving mass' mm to the 'rest mass' m0m_0 of a particle in terms of its speed vv and the speed of light, cc. (This relation first arose as a consequence of special relativity due to Albert Einstein). A boy recalls the relation almost correctly but forgets where to put the constant cc. He writes :

    m=m0(1−v2)1/2m = \frac{m_0}{\left(1 - v^2\right)^{1/2}}

    Guess where to put the missing cc.

    Easy
    3 marks
    Solve with AI
    Written solution

    Rearranging, m0m=(1−v2)1/2\dfrac{m_0}{m} = (1 - v^2)^{1/2}.

    The left-hand side is a ratio of two masses, so it is dimensionless. The right-hand side must therefore be dimensionless too. Inside the bracket the number 1 is dimensionless, and only like quantities can be subtracted, so the term subtracted from 1 must also be dimensionless. But v2v^2 has dimensions [L2T−2][\text{L}^2\text{T}^{-2}].

    Dividing v2v^2 by c2c^2 (also [L2T−2][\text{L}^2\text{T}^{-2}]) gives a dimensionless ratio. So the correct relation is

    m=m0(1−v2c2)1/2m = \frac{m_0}{\left(1 - \dfrac{v^2}{c^2}\right)^{1/2}}
  14. 14

    Question 14

    The unit of length convenient on the atomic scale is known as an angstrom and is denoted by Å: 1 A˚=10−101\ \text{Å} = 10^{-10} m. The size of a hydrogen atom is about 0.5 Å. What is the total atomic volume in m3\text{m}^3 of a mole of hydrogen atoms ?

    Medium
    3 marks
    Solve with AI
    Written solution

    Take the "size" 0.5 Å as the radius of the atom: r=0.5×10−10r = 0.5 \times 10^{-10} m.

    Volume of one atom (a sphere):

    V1=43πr3=43×3.14×(0.5×10−10)3=5.23×10−31 m3V_1 = \frac{4}{3}\pi r^3 = \frac{4}{3} \times 3.14 \times (0.5 \times 10^{-10})^3 = 5.23 \times 10^{-31}\ \text{m}^3

    One mole contains NA=6.02×1023N_A = 6.02 \times 10^{23} atoms, so the total atomic volume is

    V=NAV1=6.02×1023×5.23×10−31=3.15×10−7 m3V = N_A V_1 = 6.02 \times 10^{23} \times 5.23 \times 10^{-31} = 3.15 \times 10^{-7}\ \text{m}^3

    The atomic volume of a mole of hydrogen atoms is about 3×10−7 m33 \times 10^{-7}\ \text{m}^3 (the size is only an estimate, so 3.15×10−7 m33.15 \times 10^{-7}\ \text{m}^3 should be read as an order-of-magnitude value).

  15. 15

    Question 15

    One mole of an ideal gas at standard temperature and pressure occupies 22.4 L (molar volume). What is the ratio of molar volume to the atomic volume of a mole of hydrogen ? (Take the size of hydrogen molecule to be about 1 Å). Why is this ratio so large ?

    Medium
    5 marks
    Solve with AI
    Written solution

    Molar volume of the gas: Vg=22.4 L=22.4×10−3 m3V_g = 22.4\ \text{L} = 22.4 \times 10^{-3}\ \text{m}^3.

    Take the size 1 Å as the diameter of a hydrogen molecule, so its radius is r=0.5 A˚=0.5×10−10r = 0.5\ \text{Å} = 0.5 \times 10^{-10} m.

    Volume of one molecule:

    43πr3=43×3.14×(0.5×10−10)3=5.23×10−31 m3\frac{4}{3}\pi r^3 = \frac{4}{3} \times 3.14 \times (0.5 \times 10^{-10})^3 = 5.23 \times 10^{-31}\ \text{m}^3

    Volume actually occupied by one mole of molecules:

    VH=6.02×1023×5.23×10−31=3.15×10−7 m3V_H = 6.02 \times 10^{23} \times 5.23 \times 10^{-31} = 3.15 \times 10^{-7}\ \text{m}^3

    Ratio:

    VgVH=22.4×10−33.15×10−7=7.1×104\frac{V_g}{V_H} = \frac{22.4 \times 10^{-3}}{3.15 \times 10^{-7}} = 7.1 \times 10^{4}

    Why so large: in a gas the molecules are very far apart compared with their own size. The molecules themselves fill only about 1/(7×104)1/(7 \times 10^{4}) of the volume of the gas; the rest is empty space between them.

  16. 16

    Question 16

    Explain this common observation clearly : If you look out of the window of a fast moving train, the nearby trees, houses etc. seem to move rapidly in a direction opposite to the train's motion, but the distant objects (hill tops, the Moon, the stars etc.) seem to be stationary. (In fact, since you are aware that you are moving, these distant objects seem to move with you).

    Easy
    3 marks
    Solve with AI
    Written solution

    We judge how fast an object moves across our view by how fast the direction of our line of sight to it turns (the angle turned per second), not by distances.

    Class 11 Physics Units And Measurments

    Suppose the train moves from A to B. For a nearby tree, the line of sight turns through a large angle because the distance moved AB is comparable to the distance of the tree. The direction to the tree changes quickly, so the tree appears to rush backwards, opposite to the train's motion.

    For a hill top, the Moon or a star, the distance is enormous compared with AB. The angle subtended, which is about AB divided by the distance, is extremely small. The line of sight hardly turns, so these objects appear stationary. Because we know we are moving while their direction stays the same, they seem to move along with us.

  17. 17

    Question 17

    The Sun is a hot plasma (ionized matter) with its inner core at a temperature exceeding 10710^{7} K, and its outer surface at a temperature of about 6000 K. At these high temperatures, no substance remains in a solid or liquid phase. In what range do you expect the mass density of the Sun to be, in the range of densities of solids and liquids or gases ? Check if your guess is correct from the following data : mass of the Sun =2.0×1030= 2.0 \times 10^{30} kg, radius of the Sun =7.0×108= 7.0 \times 10^{8} m.

    Medium
    4 marks
    Solve with AI
    Written solution

    Guess: since the Sun is a gas-like plasma, one might expect a gas-like density. But the huge gravitational pull of its own mass compresses it strongly, so the density can be much higher. Let us check.

    Volume of the Sun:

    V=43πR3=43×3.14×(7.0×108)3=1.44×1027 m3V = \frac{4}{3}\pi R^3 = \frac{4}{3} \times 3.14 \times (7.0 \times 10^{8})^3 = 1.44 \times 10^{27}\ \text{m}^3

    Mean density:

    ρ=MV=2.0×10301.44×1027=1.39×103 kg m−3\rho = \frac{M}{V} = \frac{2.0 \times 10^{30}}{1.44 \times 10^{27}} = 1.39 \times 10^{3}\ \text{kg m}^{-3}

    The data have 2 significant figures, so ρ≈1.4×103 kg m−3\rho \approx 1.4 \times 10^{3}\ \text{kg m}^{-3}.

    This is in the range of densities of solids and liquids (water 1.0×1031.0 \times 10^{3}, rocks about 3×103 kg m−33 \times 10^{3}\ \text{kg m}^{-3}), not of gases (air about 1.3 kg m−31.3\ \text{kg m}^{-3}). The density is high because gravity compresses the plasma, even though it is not a solid or a liquid.

Inside Ch 1

What Class 11 Physics Ch 1 covers

The sections of the chapter, in the order the book takes them. Every question above comes from one of these.

  1. 01Physical Quantities
  2. 02Units
  3. 03Significant Figures
  4. 04Units And Dimensions Of A Few Derived Quantities
  5. 05Dimentional Formula
  6. 06Principle Of Homogeneity
Common questions

Class 11 Physics Ch 1 questions students ask

How many questions are there in Class 11 Physics Ch 1?

17 questions. Every one is solved step by step on this page.

Are these Class 11 Physics solutions free?

Yes. Every question and its full working is free to read, with no account needed.

Can I download the Class 11 Physics Ch 1 solutions as a PDF?

There is no PDF to download. Every solution is on this page instead, which means it is searchable, always the current syllabus, and readable on a phone. Use your browser's print option if you want it on paper.