Opening your dashboard
Class 12 Physics Chapter 7 Ray Optics And Optical Instruments: Previous Year Questions
37 questions on Chapter 7, each solved step by step. Class 12 Physics, CBSE 2026-27.
37 questions with solutions
1–5 marks · Hard difficulty
- 11 mark
Question 1
A ray of light of wavelength 600 nm propagates from air into a medium. If its wavelength in the medium becomes 400 nm, the refractive index of the medium is
Solve with AIAnswer
(A) 1.4
- Correct
(B) 1.5
(C) 1.6
(D) 1.8
Option (B) is correct.
Explanation: The frequency does not change on entering the medium, but the speed drops by a factor , so the wavelength also drops by :

- 21 mark
Question 2
A beam of light travels from air into a medium. Its speed and wavelength in the medium are m s⁻¹ and 230 nm respectively. The wavelength of light in air will be
Solve with AIAnswer
(A) 230 nm
(B) 345 nm
- Correct
(C) 460 nm
(D) 690 nm
Option (C) is correct.
Explanation: The refractive index is . The frequency is the same in both media, so the wavelength in air is times the wavelength in the medium:
- 31 mark
Question 3
A ray of light travels a distance of 12.0 m in a transparent sheet in 60 ns. The refractive index of the sheet is
Solve with AIAnswer
(A) 1.33
- Correct
(B) 1.50
(C) 1.65
(D) 1.75
Option (B) is correct.
Concept used — speed of light in a medium and the refractive index
Light travels at a steady speed inside a uniform medium, so its speed is distance divided by time. The (absolute) refractive index of the medium is the ratio of the speed of light in vacuum to its speed in the medium:
Given: distance in the sheet m, time taken ns s, speed of light in vacuum m s⁻¹.
To find: the refractive index of the sheet.
Step 1 — Find the speed of light in the sheet.
Step 2 — Divide by this speed.
Answer: the refractive index of the sheet is , option (B).
Why the others fail: 1.33 would need m s⁻¹ (water), and 1.65 or 1.75 would need the light to take 66 ns or 70 ns over the same 12.0 m. Note: always convert ns to s ( s) before dividing.
- 41 mark
Question 4
The direction of ray of light incident on a concave mirror is shown by PQ while directions in which the ray would travel after reflection is shown by four rays marked 1, 2, 3 and 4 (Figure). Which of the four rays correctly shows the direction of reflected ray?
Solve with AIAnswer
(A) 1
- Correct
(B) 2
(C) 3
(D) 4
Option (B) is correct.
Explanation: The incident ray PQ passes through the focus F. A ray through the focus of a concave mirror is reflected parallel to the principal axis. Only rays 2 and 4 are parallel to the axis, and ray 4 goes behind the mirror, which is impossible. So the reflected ray is 2.
- 51 mark
Question 5
When an object is placed between and of a concave mirror, the image formed is
Solve with AIAnswer
(A) Real, diminished
- Correct
(B) Real, magnified
(C) Virtual, diminished
(D) Virtual, magnified
Option (B) is correct.
Explanation: For an object between F and C (that is, between and ), the image forms beyond C. It is real, inverted and magnified.

- 61 mark
Question 6
In two positions concave mirror produces magnified image of given object. The positions are
Solve with AIAnswer
(A) (i) At C, (ii) at F
- Correct
(B) (i) Between F and C, (ii) Between P and F
(C) (i) Beyond C, (ii) Between P and F
(D) (i) At C, (ii) between P and F
Option (B) is correct.
Explanation:
- Between F and C: the image is beyond C, real, inverted and magnified.
- Between P and F: the image is behind the mirror, virtual, erect and magnified.

- An object at C gives an image of the same size.
- An object beyond C gives a smaller image.
- 71 mark
Question 7
The focal length of a concave mirror is . An object is placed at a distance from the focus. The magnification is
Solve with AIAnswer
(A)
- Correct
(B)
(C)
(D)
Option (B) is correct.
Explanation: With the object beyond F, its distance from the mirror is . In the sign convention, and the focal length is :

This is Newton's form of the mirror equation. The closer the object is to F (small ), the larger the image.
- 81 mark
Question 8
The optical density of turpentine is higher than that of water while its mass density is lower. Figure shows a layer of turpentine floating over water in a container. For which one of the four rays incident on turpentine in Figure, the path shown is correct?
Solve with AIAnswer
(A) 1
- Correct
(B) 2
(C) 3
(D) 4
Option (B) is correct.
Explanation: The optical densities are in the order .
- Air → turpentine: the ray enters a denser medium and bends towards the normal.
- Turpentine → water: the ray enters a rarer medium and bends away from the normal, but in water it stays closer to the normal than it was in air, because water is still denser than air.
Only ray 2 does both.
- 91 mark
Question 9
A short pulse of white light is incident from air to a glass slab at normal incidence. After travelling through the slab, the first color to emerge is
Solve with AIAnswer
(A) blue
(B) green
(C) violet
- Correct
(D) red
Option (D) is correct.
Explanation: The refractive index of a medium depends slightly on the wavelength of light (NCERT Section 9.3): for glass it is smallest for red light. Since , red light travels fastest in the glass. All colours cover the same thickness, so red comes out first.
- 101 mark
Question 10
The radius of curvature of the curved surface of a plano-convex lens is 20 cm. If the refractive index of the material of the lens be 1.5, it will
Solve with AIAnswer
(A) act as a convex lens only for the objects that lie on its curved side.
(B) act as a concave lens for the objects that lie on its curved side.
- Correct
(C) act as a convex lens irrespective of the side on which the object lies.
(D) act as a concave lens irrespective of the side on which the object lies.
Option (C) is correct.
Explanation: For the lens maker's formula, take and cm (or the reverse):
Turning the lens round swaps and but gives the same cm. A thin lens has the same focal length on both sides.

- 111 mark
Question 11
Radius of curvature of human eye is 0.78 cm. For an object at infinity, image is formed at 3 cm behind the refracting surface. The refractive index of eye is
Solve with AIAnswer
- Correct
(A) 1.35
(B) 3
(C) 6.2
(D) 1
Option (A) is correct.
Explanation: Refraction at a single spherical surface from air () into the eye ():

- 121 mark
Question 12
The relationship between angle of incidence , prism of angle and angle of minimum deviation for a triangular prism is
Solve with AIAnswer
(A)
- Correct
(B)
(C)
(D)
Option (B) is correct.
Explanation: In general . At minimum deviation the path is symmetric, so :

- 131 mark
Question 13
Magnifying power of a microscope depends on
Solve with AIAnswer
(A) colour of light.
(B) focal length of objective and color of light.
(C) focal length of eyepiece and color of light.
- Correct
(D) focal length of eyepiece and objective.
Option (D) is correct.
Explanation: For a compound microscope,
The magnifying power depends on the focal lengths of the objective and the eyepiece (and on the tube length). The colour of light does not appear in it.
- 141 mark
Question 14
In a compound microscope, image produced by objective is ____ and the image produced by eyepiece is ____.
Solve with AIAnswer
(A) Real, real
(B) Virtual, virtual
- Correct
(C) Real, virtual
(D) Virtual, real
Option (C) is correct.
Explanation: The objective forms a real, inverted, magnified image of the object. The eyepiece works as a simple magnifier on this image, and produces a final virtual, magnified image.

- 151 mark
Question 15
Reflecting telescope utilizes
Solve with AIAnswer
(A) Convex mirror
(B) Concave mirror
- Correct
(C) Both (A) and (B)
(D) Prism
Option (C) is correct.
Explanation: In a Cassegrain reflecting telescope, a large concave mirror (the objective) collects and focuses the light. A small convex secondary mirror reflects it back through a hole in the objective to the eyepiece.

- 162 marks
Question 16
Draw a ray diagram to show image formation when the concave mirror produces a real, inverted and magnified image of the object.
Solve with AIWritten solution
The object AB is placed between F and C. Two rays from A are used:
- one parallel to the axis, reflected through F;
- one through F (or through C), reflected back parallel to the axis (or along itself).
They meet at A′, beyond C.

The image A′B′ is real, inverted and magnified, and lies beyond C.
- 171 mark
Question 17
If a man's face is 30.0 cm in front of a concave shaving mirror creating an upright image 1.50 times as large as the object, what is the mirror's focal length?
Solve with AIWritten solution
An upright image from a concave mirror is virtual, behind the mirror. With cm:

The focal length is 90 cm (concave). The face is within F, as it must be for an upright, enlarged image.
- 181 mark
Question 18
Name the mirror which are used:
(i) As Security mirror
(ii) In Solar furnace
Solve with AIWritten solution
(i) Convex mirror. It always gives an erect, diminished image and a much wider field of view.
(ii) Concave mirror. It converges the Sun's parallel rays to its focus and concentrates the energy there.

- 192 marks
Question 19
Use the mirror equation to show that an object placed between and of a concave mirror forms an image beyond .
Solve with AIWritten solution
For a concave mirror, . An object between and has (both negative), so .
From the mirror equation, .
- At : , so .
- At : , so .
In between, lies between and 0. It is negative, and smaller in size than . So is negative with : the image is real and beyond .

- 202 marks
Question 20
State two positions in which a concave mirror produces a magnified image of a given object. List two differences between the two images.
Solve with AIWritten solution
Positions:
- Object between F and C.
- Object between P and F.

Differences between the two images:
Object between F and C Object between P and F Image is real (can be caught on a screen) Image is virtual (cannot be caught on a screen) Image is inverted Image is erect Image is in front of the mirror, beyond C Image is behind the mirror - 213 marks
Question 21
An object is placed in front of a concave mirror of focal length of 12 cm. There are two possible positions of the object for which the image formed is three times the size of the object.
(a) Draw the ray diagram for each case, and
(b) Find the distance between the two positions of the object.
Solve with AIWritten solution
(a)

(b) cm.
Real, inverted image (, so ):
Virtual, erect image (, so ):
The two positions are 16 cm and 8 cm from the mirror, so they are 8 cm apart.
- 222 marks
Question 22
A double convex lens, made of a material of refractive index , is placed inside two liquids of refractive indices and as shown. . A wide, parallel beam of light is incident on the lens from the left. How will the rays be refracted?
Solve with AIWritten solution
A lens converges light only if it is optically denser than its surroundings. By the lens maker's formula, .
- Upper half, in liquid : , so is negative and this half diverges the rays.
- Lower half, in liquid : , so is positive and this half converges the rays.

The single wide beam emerges as two beams: a diverging one from the upper half and a converging one from the lower half.
- 232 marks
Question 23
The light beam shown in the figure makes an angle of 20.0° with the normal NN′ in the linseed oil. Determine the angles and . (The refractive index of linseed oil is 1.48 and that of water is 1.333.)
Solve with AIWritten solution
Air–oil surface:
Oil–water surface:

The quantity stays the same across parallel layers.
- 241 mark
Question 24
For a glass prism () the angle of minimum deviation is equal to the angle of the prism. Find the angle of the prism.
Solve with AIWritten solution
With :

- 252 marks
Question 25
A ray of light is incident on a glass prism of refractive index and refracting angle . If it just suffers total internal reflection at the other face, obtain a relation between the angle of incidence, angle of prism and critical angle.
Solve with AIWritten solution
At the second face the ray must meet the surface exactly at the critical angle: , where .
For any prism, , so .
At the first face, Snell's law gives

- 262 marks
Question 26
In the given figure the radius of curvature of curved face in the plano-convex and the plano-concave lens is 15 cm each. The refractive index of the material of the lenses is 1.5. Find the final position of the image formed.
Solve with AIWritten solution
Focal lengths (lens maker's formula, one flat face):
Plano-convex lens: the parallel beam would converge 30 cm beyond it. That is cm beyond the plano-concave lens, so for the second lens it is a virtual object at cm.
Plano-concave lens:

The final image is formed 15 cm to the right of the plano-concave lens.
- 272 marks
Question 27
A ray of monochromatic light passes through an equilateral glass prism in such a way that the angle of incidence is equal to the angle of emergence and each of these angles is times the angle of the prism. Determine the angle of deviation and the refractive index of the glass prism.
Solve with AIWritten solution
and . Since , this is minimum deviation:

- 282 marks
Question 28
Show that the least possible distance between an object and its real image in a convex lens is , where is the focal length of the lens.
Solve with AIWritten solution
Let the object–image distance be and the image be from the lens, so the object is from it.

For a real image, and :
The lens position must be real, so the discriminant cannot be negative:
The least distance is , with the object and image each at from the lens.
- 292 marks
Question 29
Compare the focal lengths of the two lenses shown below if the radius of curvature of the curved surface is the same in both lenses.
Solve with AIWritten solution
Plano-concave lens:
Plano-convex lens:
So . The focal lengths are equal in size and opposite in sign: one lens converges and the other diverges equally strongly. Placed in contact, they would cancel ().
- 303 marks
Question 30
A ray of light is refracted by a glass prism. Obtain an expression for the refractive index of the glass in terms of the angle of prism A and the angle of minimum deviation .
Solve with AIWritten solution

Geometry. In the quadrilateral formed by the faces and the normals, . The total deviation is .
At minimum deviation the ray passes symmetrically, so and :
Snell's law at the first face:
- 315 marks
Question 31
(i) Draw a ray diagram for the formation of image of a point object by a thin double convex lens having radii of curvature and . Hence, derive lens maker's formula.
(ii) A converging lens has a focal length of 10 cm in air. It is made of a material of refractive index 1.6. If it is immersed in a liquid of refractive index 1.3, find its new focal length.
Solve with AIWritten solution
(i) Treat the lens as two refracting surfaces. The image formed by the first surface acts as the object for the second.

First surface (air to glass , radius ), object O at , intermediate image at :
Second surface (glass to air, radius ). For a thin lens, is the object at distance , and the final image is at :
Adding the two equations:
For an object at infinity, , so
This is the lens maker's formula, and the two relations together give the lens formula .
(ii) The radii are the same in both media, so
The lens still converges, but more weakly.
- 325 marks
Question 32
(a) A ray of light is incident at angle on a right-angled prism at point X. At point Y, it emerges along the prism surface. Calculate the refractive index of the prism in terms of the incident angle.

(b) Show that for an equilateral prism kept in air, minimum deviation occurs when the angle of incidence , where is the refractive index of the material of the prism.
Solve with AIWritten solution
(a) Here . At X, . At Y, the ray emerges grazing the surface, so it meets Y at the critical angle: . Since , :
Also , so

(b) At minimum deviation, for an equilateral prism. Snell's law at the first face gives
- 335 marks
Question 33
(a) A ray PQ is incident normally on the face AB of a triangular prism of refracting angle 60° as shown in figure. The prism is made of a transparent material of refractive index . Trace the path of the ray as it passes through the prism. Calculate the angle of emergence and the angle of deviation.

(b) (i) A ray of light incident on face AB of an equilateral glass prism, shows minimum deviation of 30°. Calculate the speed of light through the prism.
(ii) Find the angle of incidence at face AB so that the emergent ray grazes along the face AC.
Solve with AIWritten solution
(a) The ray enters AB normally, so it goes straight on (). It meets AC at . The critical angle is
The ray meets AC exactly at the critical angle, so it grazes along AC: .

(b)(i)
(ii) For grazing emergence at AC, with , so and :

- 345 marks
Question 34
(a) Under what conditions is the phenomenon of total internal reflection of light observed?
(b) Obtain the relation between the critical angle of incidence and the refractive index of the medium.
(c) Three lenses of focal lengths +10 cm, −10 cm and +30 cm are arranged coaxially as in the figure given below. Find the position of the final image formed by the combination.
Solve with AIWritten solution
(a) Two conditions must both hold:
- Light travels from an optically denser medium towards a rarer one.
- The angle of incidence is greater than the critical angle for that pair of media.
(b) At the critical angle , the refracted ray grazes the surface (). Snell's law from the denser medium (index ) to air:
(c) Concept used — the thin-lens formula, applied lens by lens
For each thin lens (Cartesian sign convention, light travelling left to right, distances measured from that lens),
The image formed by one lens is the object for the next lens. If that image lies beyond the next lens (the light is still converging towards it when it reaches the lens), it is a virtual object with a positive .
Given (from the figure): object 30 cm to the left of lens 1; lens 1 ( cm), lens 2 ( cm) 5 cm to the right of lens 1, lens 3 ( cm) 10 cm to the right of lens 2.
Step 1 — Image formed by lens 1. Here cm and cm.
So lens 1 would form a real image 15 cm to its right.
Step 2 — This image is a virtual object for lens 2. Lens 2 is only 5 cm from lens 1, so the light meets lens 2 before reaching that image point, which lies cm to the right of lens 2. Hence cm, with cm:
The light leaves lens 2 as a parallel beam (the virtual object sits exactly at the focus of the concave lens).
Step 3 — Lens 3 receives parallel light. For lens 3, (so ) and cm:

Answer: the final image is formed 30 cm to the right of the third lens (real, at the focus of lens 3).
Note: the separation of lens 3 from lens 2 does not matter here, because the beam between them is parallel.
- 355 marks
Question 35
(i) Draw a ray diagram to show the working of a compound microscope. Obtain the expression for the total magnification for the final image to be formed at the near point.
(ii) In a compound microscope an object is placed at a distance of 1.5 cm from the objective of focal length 1.25 cm. If the eye-piece has a focal length of 5 cm and the final image is formed at the near point, find the magnifying power of the microscope.
Solve with AIWritten solution
(i)

The objective forms a real, inverted, magnified image A′B′ just inside the focus of the eyepiece. The eyepiece, acting as a simple magnifier, forms the final virtual image A″B″ at the near point D.
- Objective: (approximately , where is the tube length).
- Eyepiece: with the final image at the near point, .
(ii) Objective, cm, cm:
The magnifying power is 30. The minus sign shows that the final image is inverted.
- 361 mark
Question 36
Assertion (A): Propagation of light through an optical fibre is due to total internal reflection taking place at the core-cladding interface.
Reason (R): Refractive index of the material of the cladding of the optical fibre is greater than that of the core.
Solve with AIAnswer
(A) Both Assertion (A) and Reason (R) are true, and Reason (R) is the correct explanation of Assertion (A).
(B) Both Assertion (A) and Reason (R) are true, but Reason (R) is not the correct explanation of Assertion (A).
- Correct
(C) Assertion (A) is true, but Reason (R) is false.
(D) Both Assertion (A) and Reason (R) are false.
Option (C) is correct.
Explanation:
- A is true: light is guided along the fibre by repeated total internal reflection at the core–cladding boundary.
- R is false: total internal reflection happens only when light goes from a denser to a rarer medium, so the core must have the higher refractive index.

- 371 mark
Question 37
Assertion (A): If the focal length of two convex lenses is the same, the lens with the larger diameter will produce brighter images.
Reason (R): Convex lenses with larger diameters are able to focus light better.
Solve with AIAnswer
(A) Both Assertion (A) and Reason (R) are true, and Reason (R) is the correct explanation of Assertion (A).
(B) Both Assertion (A) and Reason (R) are true, but Reason (R) is not the correct explanation of Assertion (A).
- Correct
(C) Assertion (A) is true, but Reason (R) is false.
(D) Both Assertion (A) and Reason (R) are false.
Option (C) is correct.
Explanation:
- A is true: a lens of larger diameter collects more light (the light collected is proportional to the area, ), so the image, of the same size, is brighter.
- R is false: lenses of the same focal length bring light to a focus at the same place. A bigger diameter does not make the focusing "better". This is why telescopes use large objectives to gather light (NCERT section 9.7.2).
