Opening your dashboard
Class 11 Physics Chapter 11: Thermodynamics Solutions
8 textbook questions with step-by-step answers, free to read, for CBSE 2026-27.
Get talked through Ch 11, not just shown the answer
Reading a finished solution is not the same as being able to do it. The AI tutor takes one question at a time and works it with you, in your own words, until you can.
- Ask it out loud, in your own words
- It gives you the next step, not the answer
- Stuck on part (ii)? Start there
8 questions with solutions
3–4 marks · Medium difficulty
- 13 marks
Question 1
A geyser heats water flowing at the rate of litres per minute from to . If the geyser operates on a gas burner, what is the rate of consumption of the fuel if its heat of combustion is ?
Solve with AIWritten solution
Mass of water heated per minute: the density of water is per millilitre, so litres of water has a mass
Heat needed per minute: take the specific heat capacity of water as . The rise in temperature is , so
Fuel burnt per minute: each gram of fuel releases on burning. Assuming all of this heat goes into the water, the mass of fuel burnt each minute is
The fuel is consumed at about , that is, roughly of fuel every minute.
- 23 marks
Question 2
What amount of heat must be supplied to of nitrogen (at room temperature) to raise its temperature by at constant pressure? (Molecular mass of ; .)
Solve with AIWritten solution
Number of moles: the mass is and the molar mass of is , so
Molar specific heat at constant pressure: nitrogen is a diatomic gas. For a diatomic gas at room temperature, the molar specific heat at constant pressure is
(This value for diatomic gases is explained in Chapter 12, Kinetic Theory; here it is used as a known value.)
Heat supplied: a rise of is the same as a rise of . At constant pressure,
About (≈ ) of heat must be supplied.
(The book's 933.4 J comes from rounding μ to 0.714 mol first.)
- 34 marks
Question 3
Explain why
(a) Two bodies at different temperatures and if brought in thermal contact do not necessarily settle to the mean temperature .
(b) The coolant in a chemical or a nuclear plant (i.e., the liquid used to prevent the different parts of a plant from getting too hot) should have high specific heat.
(c) Air pressure in a car tyre increases during driving.
(d) The climate of a harbour town is more temperate than that of a town in a desert at the same latitude.
Solve with AIWritten solution
(a) Heat flows from the hotter body to the colder one until both reach a common temperature . If no heat is lost, the heat lost by one equals the heat gained by the other. With masses and specific heats (and ),
This equals only when the two heat capacities are equal, . In general they are not, and the final temperature lies closer to the starting temperature of the body with the larger heat capacity.
(b) The heat a coolant can carry away is . A liquid with a high specific heat absorbs a large amount of heat for only a small rise in its own temperature. So a given mass of coolant can remove a lot of heat from the hot parts of the plant while staying cool itself, which makes the cooling effective.
(c) While the car is driven, the tyre is repeatedly squashed and flexed and it rubs against the road. The work done on the tyre in this way warms the tyre and the air inside it. The volume of the tyre stays nearly constant, and for a fixed amount of gas at constant volume the pressure is proportional to the absolute temperature (). As the air temperature rises, its pressure rises.
(d) Water has a much higher specific heat than sand or soil. Near a harbour, the sea absorbs a great deal of heat in summer (and by day) with only a small rise in temperature, which keeps the town from getting very hot. In winter (and at night) the sea gives this heat back slowly, which keeps the town from getting very cold. In a desert, sand has a low specific heat, so it heats up and cools down quickly, giving very hot days and very cold nights. Hence the climate of the harbour town is more temperate.
- 44 marks
Question 4
A cylinder with a movable piston contains 3 moles of hydrogen at standard temperature and pressure. The walls of the cylinder are made of a heat insulator, and the piston is insulated by having a pile of sand on it. By what factor does the pressure of the gas increase if the gas is compressed to half its original volume?
Solve with AIWritten solution
Type of process: the walls of the cylinder and the piston are both insulated, so no heat can enter or leave the gas (). The compression is therefore adiabatic.
For an adiabatic process of an ideal gas,
where . For hydrogen, a diatomic gas, .
Pressure ratio: with ,
The pressure increases by a factor of about . The ratio depends only on the volume ratio and ; the amount of gas (3 moles) and the starting state (STP) do not affect it.
- 53 marks
Question 5
In changing the state of a gas adiabatically from an equilibrium state to another equilibrium state , an amount of work equal to is done on the system. If the gas is taken from state to via a process in which the net heat absorbed by the system is , how much is the net work done by the system in the latter case? (Take .)
Solve with AIWritten solution
First law: , where is the heat absorbed by the system and is the work done by the system.
Adiabatic path from A to B: no heat is exchanged, so . Work of is done on the system, so the work done by it is .
Second path from A to B: internal energy is a state variable, so is the same, , for any path between the same two states. The heat absorbed is
so the work done by the system is
The net work done by the system along the second path is about .
- 64 marks
Question 6
Two cylinders and of equal capacity are connected to each other via a stopcock. contains a gas at standard temperature and pressure. is completely evacuated. The entire system is thermally insulated. The stopcock is suddenly opened. Answer the following:
(a) What is the final pressure of the gas in and ?
(b) What is the change in internal energy of the gas?
(c) What is the change in the temperature of the gas?
(d) Do the intermediate states of the system (before settling to the final equilibrium state) lie on its -- surface?
Solve with AIWritten solution
When the stopcock is opened, the gas rushes from into the empty cylinder . This is a free expansion. Work out the energy first.

- The system is thermally insulated, so no heat enters or leaves: .
- The gas expands into a vacuum. It pushes against nothing and no piston moves, so it does no work: .
By the first law,
The internal energy of an ideal gas depends only on its temperature, so an unchanged internal energy means an unchanged temperature.
(a) The temperature is the same at the end as at the start, and the volume doubles (from to , since the cylinders have equal capacity). For a fixed amount of gas at the same temperature, :
The final pressure in both and is .
(b) The change in internal energy is zero, because and .
(c) The change in temperature is zero (for an ideal gas), because its internal energy depends only on temperature and .
(d) No. The expansion is sudden and uncontrolled. While the gas is rushing into , it does not have a single well-defined pressure and temperature throughout; different parts of the gas are in different conditions. These intermediate states are non-equilibrium states, so they cannot be described by values of , and that satisfy the equation of state. They therefore do not lie on the -- surface. Only the initial and final equilibrium states lie on it.
- 74 marks
Question 7
An electric heater supplies heat to a system at a rate of . If system performs work at a rate of joules per second, at what rate is the internal energy increasing?
Solve with AIWritten solution
Apply the first law, , to what happens in each second.
In one second the heater supplies of heat (since ), and the system does of work. So in each second
The internal energy of the system increases at the rate of , that is, .
- 83 marks
Question 8
A thermodynamic system is taken from an original state to an intermediate state by the linear process shown in the figure.

Its volume is then reduced to the original value from E to F by an isobaric process. Calculate the total work done by the gas from D to E to F.
Solve with AIWritten solution
The work done by a gas is the area under its path on the - diagram: positive when the volume increases, negative when it decreases.
D to E (expansion along a straight line): the area under DE is a trapezium of width with parallel sides and :
E to F (isobaric compression at ): the volume falls by , so
Total work done by the gas:

This is just the area of the shaded triangle DEF, with base and height :
The total work done by the gas from D to E to F is (positive, because more work is done by the gas during the expansion than is done on it during the compression).
What Class 11 Physics Ch 11 covers
The sections of the chapter, in the order the book takes them. Every question above comes from one of these.
- 01Thermal Equilibrium
- 02Zeroth Law Of Thermodynamics
- 03Heat Internal Energy And Work
- 04First Law Of Thermodynamics
- 05Specific Heat Capacity
- 06Thermodynamic State Variable
More ways to study this chapter
The same chapter asked three other ways. Practise it, revise it, and see what the board has set on Ch 11 before.
Class 11 Physics Ch 11 questions students ask
How many questions are there in Class 11 Physics Ch 11?
8 questions. Every one is solved step by step on this page.
Are these Class 11 Physics solutions free?
Yes. Every question and its full working is free to read, with no account needed.
Can I download the Class 11 Physics Ch 11 solutions as a PDF?
There is no PDF to download. Every solution is on this page instead, which means it is searchable, always the current syllabus, and readable on a phone. Use your browser's print option if you want it on paper.
